• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.15 no.3
• /
• pp.77-81
• /
• 2009

There has been an increasing demand on measurement of the vibration levels in commercial truck shipments, where all packaged products are exposed to some levels of random vibration and shock. In this study, bear glass bottles loaded at the front, middle, and rear positions of 11 tonne truck bed was shipped from Kwangju to Waegouan. Vertical direction vibration levels were analysed and matching laboratory random vibration test was performed using power spectral density (PSD) profiles derived from truck transit records. Also, the effects of drop hight on glass bottles were evaluated. As expected, the maximum vibration levels were recorded at the rear of truck bed. No breakage of bottles were observed during truck transit and laboratory random vibration testing set at 0.52 $G_{rms}$. In drop test, glass bottles were not damaged by bottom side impact, while short side drop impact caused about twice higher bottle breakage rate than that of long side drop impact at 30 cm and 40 cm drop hight.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.4
• /
• pp.537-543
• /
• 2003

Transient vibration generated by developing localized fault in gear can be used as indicators in gear fault detection. This vibration signal suffers from the background noise such as gear meshing frequency and its harmonics and broadband noise. Thus in order to extract the information about the only gear fault from the raw vibration signal measured on the gearbox this signal is processed to reduce the background noise with many kinds of signal-processing tools. However, these signal-processing tools are often very complex and time waste. Thus. in this paper. we propose a novel approach detecting the damage of gearbox and analyzing its pattern using the raw vibration signal. In order to do this, the residual signal. which consists of the sideband components of the gear meshing frequent) and its harmonics frequencies, is extracted from the raw signal by the power spectral density (PSD) to obtain the information about the fault and is used as the input data of the artificial neural network (ANN) for analysis of the pattern of gear fault. This novel approach has been very successfully applied to the damage analysis of a laboratory gearbox.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.10a
• /
• pp.68-73
• /
• 1995

반사음이 포함된 신호의 계측을 통하여 원음의 크기와 반사계수의 크기, 지연시간 등의 추출을 수치적 예를 사용하여 규명해 보았다. 반사계수의 측정시, 폐쇄된 음장에서는 정상파비로 표시되는 단일 주파수 신호를 사용하는 것이 실제 계측시 가장 손쉬운 방법이며, 광역의 주파수 성분에 걸쳐 그 값을 파악할 필요가 있는 경우에는 켑스트럼 상에서 반사파의 효과가 원음과 확연히 구분되는 신호를 사용하는 것이 신호처리 과정에서 불필요한 부담을 제거시켜 준다. 개방 음장에서는 반사파가 1개 밖에 포함되지 않으므로 이 경우에는 PSD 상의데이터 처리를 통하든지 또는 캡스트럼의 재편집을 통하여 원음의 크기와 성분 그리고 반사계수 등을 손쉽게 추출해 낼 수 있다. 광대역 주파수 성분을 가진 음원을 계측에 사용할 경우에는 comb lifter의 적용에 보다 세심한 주의를 기울일 필요가 있으며 켑스트럼 상의 추가 충격응답함수의 식별에 보다 더 합리적인 방법이 강구되어야 할 것이다.

• Journal of KSNVE
• /
• v.9 no.3
• /
• pp.502-508
• /
• 1999

Newly developed control methodology applied to dynamic system under random disturbance is investigated and its performance is verified experimentall. Flexible cantilever beam sticked with piezofilm sensor and piezoceramic actuator is modelled in physical domain. Dynamic moment equation for the system is derived via Ito's stochastic differential equation and F-P-K equation. Also system's characteristics in stochastic domain is analyzed simultaneously. LQG controller is designed and used in physical and stochastic domain as wall. It is shown experimentally that randomly excited beam on the base is controlled effectively by designed LQG controller in physical domain. By comparing the result with that of LQG controller designed in stochastic domain, it is shown that new control method, what we called $\ulcorner$Heo-stochastic controller design technique$\lrcorner$, has better performance than conventional ones as a controller.

• The Bulletin of The Korean Astronomical Society
• /
• v.42 no.1
• /
• pp.57.3-58
• /
• 2017

Single Point Diamond Turning (SPDT) is a cost-effective technique to fabricate metallic mirrors. In particular, the servo-assisted diamond turning option is highly useful for the fabrication of freeform surfaces. However, the SPDT process leaves periodic tool marks on machined mirror surfaces, leading to undesirable diffraction effect, as well as the deviation of input beam. In order to solve this problem, we propose new SPDT machining conditions to minimize tool marks. We will also show the results from optical measurement and Power Spectral Density (PSD) analysis to evaluate the expectable performance for applications in wide field infrared telescopes.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.303-303
• /
• 2000

It is difficult to determine the static axle weight of a vehicle with weigh-in-motion systems which in absence measure instantaneous axle impact forces. The difficulty in determining a static axle weight results from dynamic effects induced by vehicle/road interactions. One method to improve the problem is to quantify a statistical confidence level for measured axle weight. The quarter-car model is used to simulate vehicle motion, Also, the road input to vehicle model can be characterized in statistical terms by PSD (power spectral density) of appropriate amplitude and frequency contents other than an exact spatial distribution. The confidence levels for the measured axle weight can be obtained by the random process analysis using both vehicle model and road input.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.42-47
• /
• 2014

In this paper, fatigue life analysis of each structure was performed through theoretical analysis method at design stage in order to verify the success or failure of the store's acoustic noise durability according to the Method 515.5 standard of MIL-STD-810F. In addition, experimental analysis was carried out through the ground and flight test by manufacturing the measuring store, and verification of the sound durability was completed through the flight test after manufacture of the actual store. Furthermore, the commercial FEM code through the PSD calculation method applying measured SPL enables verify the durability of new store components development for the future.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.16 no.5 s.110
• /
• pp.521-528
• /
• 2006

The vibration fatigue is suitable case of fatigue problem that system is exposed to the random or other irregular sources. Even some kinds of effort using power spectral density (PSD) and statistical concept was presented to cope with the intangible force signal, it is still lack of providing a reasonable solution when its exciting frequency is near or beyond of first eigenvalue. In this paper, energy approach method is presented to calculate a vibration induced fatigue damage in frequency domain. Since the corresponding damage become much larger than nominal case when the vibration is coupled with a mode shape of given structure, the new technique compensate the characteristics of structure with a measured frequency response function (FRF) between forcing acceleration and responding stress.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.2
• /
• pp.85-89
• /
• 2012

This paper presents a study on the system identification of the in-situ output shaft torque measurement system using a non-contacting magneto-elastic torque transducer installed in a vehicle drivline. The frequency response (transfer) function (FRF) analysis is conducted to interpret the dynamic interaction between the output shaft torque and road side excitation due to the road roughness. In order to identify the frequency response function of vehicle driveline system, two power spectral density (PSD) functions of two random signals: the road roughness profile synthesized from the road roughness index equation and the stationary noise torque extracted from the original torque signal, are first estimated. System identification results show that the output torque signal can be affected by the dynamic characteristics of vehicle driveline systems, as well as the road roughness.

• Structural Engineering and Mechanics
• /
• v.12 no.4
• /
• pp.409-428
• /
• 2001

The characteristics of dynamic wheel loads of heavy vehicles running on bridge and rigid surface are investigated by using three-dimensional analytical model. The simulated dynamic wheel loads of vehicles are compared with the experimental results carried out by Road-Vehicles Research Institute of Netherlands Organization for Applied Scientific Research (TNO) to verify the validity of the analytical model. Also another comparison of the analytical result with the experimental one for Umeda Entrance Bridge of Hanshin Expressway in Osaka, Japan, is presented in this study. The agreement between the analytical and experimental results is satisfactory and encouraging the use of the analytical model in practice. Parametric study shows that the dynamic increment factor (DIF) of the bridge and RMS values of dynamic wheel loads are fluctuated according to vehicle speeds and vehicle types as well as roadway roughness conditions. Moreover, there exist strong dominant frequency resemblance between bounce motion of vehicle and bridge response as well as those relations between RMS values of dynamic wheel loads and dynamic increment factor (DIF) of bridges.