• 전력전자학회논문지
• /
• 제25권2호
• /
• pp.79-86
• /
• 2020

This study examines the power generation characteristics of a vehicle rooftop photovoltaic module with urban driving conditions. Actual test data with an illuminometer and a thermometer were used to analyze the power generation characteristics of the vehicle rooftop photovoltaic module. In addition, the power generation characteristics were analyzed in terms of urban driving conditions, irradiance, ambient temperature, and photovoltaic module temperature. This study also analyzes the power generation characteristics of the vehicle rooftop photovoltaic module with urban driving conditions through a wavelet transform filtering method. The power generation characteristics of the vehicle rooftop photovoltaic module with urban driving conditions depend on the change in irradiance rather than that in photovoltaic module temperature.

• 한국전기전자재료학회논문지
• /
• 제31권3호
• /
• pp.182-187
• /
• 2018

In this study, 20.8% of a p-type Si bifacial solar cell was used to develop a photovoltaic (PV) module to obtain the maximum power under a limited installation area. The transparent back sheet material was replaced during fabrication with a white one, which is opaque in commercial products. This is very beneficial for the generation of more electricity, owing to the additional power generation via absorption of light from the rear side. A new model is suggested herein to predict the power of the bifacial PV module by considering the backside reflections from the roof and/or environment. This model considers not only the frontside reflection, but also the nonuniformity of the backside light sources. Theoretical predictions were compared to experimental data to prove the validity of this model, the error range for which ranged from 0.32% to 8.49%. Especially, under $700W/m^2$, the error rate was as low as 2.25%. This work could provide theoretical and experimental bases for application to a distributed and microgrid network.

• 대한전기학회논문지:전력기술부문A
• /
• 제48권11호
• /
• pp.1410-1416
• /
• 1999

This paper aims at investigating the operating-mode characteristics of two-module Thyristor Controlled Series Compensator (TCSC) as an equivalent of the multi-module TCSC in a simple three-phase power transmission system. The load flow program is developed to analyze the steady-state characteristics of two-module TCSC system and to find the thyristor firing angles for the required real power flow. The stability calculation program is developed with Poincare mapping theory. Simulation studies of the TCSC power transmission system using EMTP are performed to evaluate the transient characteristics of two-module TCSC as a real power flow controller and to rpove the results of the load flow calculation and the stability analysis. In the process of the study, the operating-mode characteristics of two-module TCSC are evaluated and compared to those of single-module TCSC.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 하계종합학술대회 논문집(2)
• /
• pp.459-462
• /
• 2004

In this paper, we present a reducing power consumption of a scheduling for module selection under the time constraint. A a reducing power consumption of a scheduling for module selection under the time constraint execute scheduling and allocation for considering the switching activity. The focus scheduling of this phase adopt Force-Directed Scheduling for low power to existed Force-Directed Scheduling. and it constructs the module selection RT library by in account consideration the mutual correlation of parameters in which the power and the area and delay. when it is, in this paper we formulate the module selection method as a multi-objective optimization and propose a branch and bound approach to explore the large design space of module selection. Therefore, the optimal module selection method proposed to consider power, area, delay parameter at the same time. The comparison experiment analyzed a point of difference between the existed FDS algorithm and a new FDS_RPC algorithm.

• 한국정보통신학회논문지
• /
• 제23권5호
• /
• pp.487-494
• /
• 2019

소형인공위성 전력시스템체계 설계 및 개발방법은 태양풍 자계인 우주환경의 영향에 따라 기술적 제약이 큰 편이다. 이를 극복하기 위해 최근 전력모듈을 융합화와 유닛화 단계별 개발 방식으로 변화 하고 있다. 모듈화 단계에서는 탑재체 전력공급 모듈 요구조건과 함께 유니버설미들웨어를 사용하여 융합하였다. 융합모듈화대상은 탑재체에서 전력분배, 부하관리, 서브유닛의 전원공급체계와 지속성을 고려한 최종모듈 설계 및 개발 단계를 범위로 한다. 본 연구는 위성본체에서 공급되는 전력모듈을 유니버설미들웨어 기반으로 전력모듈의 정밀성과 수요처모듈데이터를 컨텐츠화 하였다. 이 동적시스템과 전력서비스 모듈화는 전력분배모듈과 전원공급모듈간 상호작용으로 Range Control 알고리즘으로 제어된다. 그리하여 전력모듈 설계단계에서 탑재체 전력수요 변수의 변동성에 따른 불확실성을 해소하고 설계의 효율성을 제시하였다.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2013년도 추계학술대회 논문집
• /
• pp.79-80
• /
• 2013

MMC(Modular Multilevel Converter)는 여러 개의 Power Module을 직렬로 연결하여 정현파에 가까운 고전압의 파형을 얻을 수 있는 토폴로지로 대용량 전력변환 분야의 요구를 만족하면서 전력 품질을 향상시킬 수 있어 근래에 상당히 주목받고 있다. 당사에서는 5Mvar급 STATCOM(STATic synchronous COMpensator)을 MMC 형태로 제작하였다. 제작된 5Mvar급 STATCOM은 한 상당 12대의 Power Module로 구성하여 25-Level로 제작되었다. 제어시스템은 DSP(Digital Signal Processor)를 이용하였으며, 하나의 Main Controller와 다수의 Cell Controller, FPGA 보드 등으로 구성되어 있다. Controller 간의 상호 정보를 교환하기 위해 CAN 통신을 이용하였고, Power Module의 스위칭을 위한 보드는 각각에 연결되어 있으며, Cell Controller보드와는 절연을 위해 광신호로 연결하였다. 본 논문에서는 MMC 시스템의 제어기간 CAN 통신인터페이스와 Power Module의 PWM 동기화에 대해 설명을 하였다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.386-389
• /
• 2008

This study has analysed power output characteristics of transparent thin-film PV module depending on incidence angle and azimuth. The simulation results was evaluated power outputs of transparent thin-film PV module depending on incidence angle and azimuth after calibrating the experimental and computed data. As a result, the best power output performance of transparent thin-film PV module was obtained at slope of $30^{\circ}$ to the south, producing the annual power output of 977kWh/kWp. The annual power output data demonstrated that the PV module with a slope of $30^{\circ}$ could produce a 68 % higher power output than that with a slope of $90^{\circ}$, with respect to the inclined slope of the module. Furthermore, the PV module facing south showed a 22 % higher power output than that facing to the east in terms of the angle of the azimuth.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2005년도 전력전자학술대회 논문집
• /
• pp.279-282
• /
• 2005

Recently, due to the launching of digital broadcasting service, a demand of PDP TV with large screen size is sharply rising. PDP power module is mainly divided into power factor correction (PFC) stage and sustaining power stage. Especially, sustaining power module has pulsating load characteristics. So, the hard switching at light load condition causes low efficiency and thermal problem. Therefore, a new power conversion circuit for sustaining power module of 60' PDP is proposed whose ZVS is obtained by additional ZVS tank. This paper presents properties of the proposed converter through mode analysis, numerical analysis. And a 900w prototype for sustaining power module of 60' PDP is produced to verify the analytic results. As an experimental results, ZVS is achieved from full load to 10% load variation and more than 92% of high efficiency is obtained at 10% load condition.

• 조명전기설비학회논문지
• /
• 제26권12호
• /
• pp.1-8
• /
• 2012

The performance and lighting characteristics of the LED depend on cooling condition because the power LED generates lots of heat. In this paper, the effect of the generated heat from power LED module on lighting characteristics and performance is measured and evaluated. For experiments, the transient temperature of a power LED module with cooling condition is measured. In addition, the temperature and lighting characteristics of the LED module are measured during the steady state. As a result, the cooling condition is less effective on the lighting characteristics of the LED module at rated current but the cooling condition extremely affects those of the LED module over the rated current. Because high temperature of the power LED module causes the low phosphor conversion, luminance efficiency becomes low and color temperature becomes high. When power LED module are driven over the rated condition, higher temperature is directly related to lighting characteristics and performance of the LED module rather than higher current.

• 한국정보통신학회논문지
• /
• 제8권5호
• /
• pp.1068-1073
• /
• 2004

전원장치의 소형화 핵심기술인 반도체 스위칭 기술을 이용하여 5 V/500 mA급 트랜스리스형 파워모듈(transless type power module)을 설계하였다. 파워 모들은 강압형 chopper 방식을 이용하였으며, 스위칭회로, 제어회로, 전압검출회로, 그리고 정전압 회로 등으로 구성되어 었다. 본 연구에서 설계한 스위칭 파워모듈은 0.2 V의 load regulation, 0.1 V의 line regulation, 85 mVp-p의 output ripple 전압, 64.7 kHz의 스위칭 주파수, 최대 58% 정도의 효율을 나타내었으며, 신뢰성 및 EMC 평가항목을 만족하였다.