• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.5
• /
• pp.419-425
• /
• 2016

A powder spreading phenomenon is one of disadvantageous characteristics of the powder bed fusion process using electron beams. The powder spreading phenomenon can be controlled using a pre-heating process of metallic powders. The aim of this paper was to investigate the preheating process of Stellite21 powder using electron beams. Powder spreading experiments were performed to examine the influence of process parameters on the spreading behaviors of Stellite21 powder. Powder heating experiments were carried to investigate the effects of the focusing current of the electron beam on the quality of the heated region. Using the results of the powder spreading and heating experiments, an appropriate combination of process parameters was obtained. The pre-heating experiment of Stellite21 was performed using the estimated combination of process parameters. The results of preheating experiments showed that the preheated Stelllite21 layer with desired characteristics can be created when the estimated combination of process parameters is applied.

• Laser Solutions
• /
• v.3 no.3
• /
• pp.21-29
• /
• 2000

For the direct metal shape processing the powder feed device which is different from the widely used in rapid prototyping. is developed, The three dimensional object is shaped with the melting metal powder. The developed research has applied to rapid prototyping in ultraprecision for MEMS and medical science fields required of rapid manufacture of complex shape. The goal of this study make 3D model which has precision accuracy. Powder spreading apparatus has been more improved because that the control of powder spread is very important in layer manufacturing. It consists of the vibration motor, nozzle and tube which supplies various metal powder. This apparatus could control the spreading velocity that could control powder spreading thickness. Laser on/off switch was adapted because laser scanning velocity must be preserved constantly to prevent heat transformation of laser overheating. The error between sintered thickness md experimental one occurred by shrinkage in sintering melting process. The problem of heat transformation was solved by On/Off switching system.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.7
• /
• pp.18-25
• /
• 1998

A prototyping process based on the technique of selective ${\CO_2}$ laser sintering has been carried out using bronze powder. The integration of a ${\CO_2}$ laser and a working table to create the opto-mechanical system has been constructed for making the multi-layer sintering. Three dimensional rapid prototyping process which has used the 40W ${\CO_2}$ laser and bronze powder has been investigated experimentally The optimal scanning method has been found to minimize the deflection and distortion by using the thermal strain method which the laser scans in the x and v directions repeatedly. The method of spreading powder has been improved by using the rubber knife of which the flexibility causes less wave of spreading powder.

• The Journal of Korean Medicine Ophthalmology and Otolaryngology and Dermatology
• /
• v.11 no.1
• /
• pp.197-218
• /
• 1998

In this study, I invastigate about oriental medical drug, dosage form and directions in external therapy of contact dermatitis. and after study on relationship oriental medical drug, dosage form and directions with cause, symptom and differentiation of symptom and sign. The results are as follows; 1. Most frequently used oriental medical drug is until qing(淸) dynasty Eriocheir sinensis H. Milne-Edwards(蟹), Salix babylonica L.(柳葉), Natrii sulfas(芒硝), Allium macrostemon Bge.(해), Nelumbo nucifera Gaertn.(荷葉), nowadays in Korea and China Phellodendron amurense Rupr.(黃柏), Gypsum(石膏), Rheum palmatum L.(大黃), Baphicacanthus cusia Bremek(靑黛), Talcum(滑石). 2. In the frequency of dosage form, until qing(淸) dynasty powder 1case, liquor 49cases, liquer and solid mixture 58cases, nowadays Korea and China powder 16cases, liquor 96cases, liquer and solid mixture 59cases. 3. Most frequently used directions of dosage is thinly attaching method(薄貼法), attaching method(敷貼法), furnigating and cleansing method(熏洗法), cleansing method(洗傷法), wet dressing method(濕敷法), spreading powder method(撲粉法), plaster method(途차法), rubbing skin method(摩擦法) 4. In the external therapy of contact dermatitis, oriental medical drug's usage is based on stage of contact dermatitis In acute stage, most frequently used drug is heat and damp remove drug(淸熱燥濕藥), nature of drug(藥性) is bitter taste and cold charactor(苦寒), In chronic stage, most frequently used drug is nourishing the blood drug(養血藥), promoting blood circulation drug(活血藥). 5. The dosage form of drug is based on symptom. In acute stage, when papules and vesicles, or erosion and exudation is the main symptom of skin, liquor or powder is used, when erosion and crust is the main symptom of skin, plaster is used. In chronic stage, plaster is used. 6. In the directions of dosage is based on dosage form of drug and symptom. In acute stage, when papules and vesicles is the main symptom of skin, fumigating and cleansing method, cleansing method, plaster method is used, when erosion, vesicles and exudation the main symptom of skill, cleansing method, wet dressing method, spreading powder method, attaching method, spreading powder method is used, when crust is the main symptom of skin, plaster method is used. In chronic stage, plaster method, rubbing skin method is used.

• Journal of Powder Materials
• /
• v.9 no.4
• /
• pp.235-244
• /
• 2002

The effects of residual impurities on solid state sintering of the powder injection molded (PIMed) W-15wt%Cu nanocomposite powder were investigated. The W-Cu nanocomposite powder was produced by the mech-ano-chemical process consisting of high energy ball-milling and hydrogen reduction of W blue powder-cuO mixture. Solid state sintering of the powder compacts was conducted at $1050^{\circ}C$ for 2~10 h in hydrogen atmosphere. The den-sification of PIM specimen was slightly larger than that of PM(conventional PM specimen), being due to fast coalescence of aggregate in the PIM. The only difference between PIM and PM specimens was the amount of residual impurities. The carbon as a strong reduction agent effectively reduced residual W oxide in the PIM specimen. The $H_2O$ formed by $H_2$ reduction of oxide disintegrated W-Cu aggregates during removal process, on the contrary to this, micropore volume rapidly decreased due to coalescence of the disintegrated W-Cu aggregates during evolution of CO.It can be concluded that the higher densification was due to the earlier occurred Cu phase spreading that was induced by effective removal of residual oxides by carbon.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.8
• /
• pp.1396-1400
• /
• 2007

In this study, poly(iso-butyl methacrylate-co-ethylene glycol dimethacrylate) [poly(iso-BMA-co-EGDMA)] microgel was prepared and used as a face powder additive. The spreading, adhesiveness, and skin reactivity of poly(iso-BMA-co-EGDMA) microgel-containing face powder II were investigated and compared with the same properties of commercially available Silica bead 700-containing face powder I. In the results, the particle size of the poly(iso-BMA-co-EGDMA) microgel was significantly swelled as a result of sebum absorption. Face powder II showed a lower primary irritation index and a higher adhesiveness than did face powder I. Face powder I showed a low sebum absorption ratio and a relatively high rate of sebum absorption, whereas face powder II, contrastingly, exhibited a high sebum absorption ratio and a low rate of sebum absorption, which properties would reduce the phenomena of facial strain and sliminess. These results indicate that poly(iso- BMA-co-EGDMA) microgel has outstanding sebum absorption characteristic and adhesiveness, and thus that it is a good candidate for use as a face powder additive.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.4
• /
• pp.64-68
• /
• 1987

To develope the utilities of the chestnut bur, which is wasted after harvesting chestnut in farmhouses, the feasibilities of adhesion(urea resin) extenders of the powder for plywood were examined. These experiments were implemented on experimental scale at Forestry Research Institute(Seoul) and on a plywood mill scale at Eugon Industrial Co LTD(Inchon) for more reliable data. In this paper, it was proved that the chestnut bur powder caused to rise the glue viscosity but the chaff powder to down reversely. The most effective mixing ratio were wheat flour 5kg, chaff powder: 5kg and chestnut bur powder. 5kg per 100kg of urea resin. At this condition, the viscosity were most appropriate (1,320 2,230 cps) for glue spreading operations, and the dry shear strengthes were most adequate(10.7-13.2kg/$cm^2$), wood failure ratio 82-88%). The chestnut bur powder, can be utilized for plywood adhesion extenders without any change of present process lines in plywwod mills.

• Korean Journal of Agricultural Science
• /
• v.43 no.4
• /
• pp.589-594
• /
• 2016

The objective of the current study was to investigate the effect of odor reducing agents on the levels of pH, total carbon, total nitrogen, and odorous compounds [phenols, indoles, short chain fatty acid (SCFA), branched-chain fatty acid (BCFA), and ammonium nitrogen] of swine manure during the spring season (temperature around $20^{\circ}C$). Odor reducing agents included horseradish powder, mushroom waste powder, and almond hull powder. A manure sample (15 L) was taken from the pit under the pens of a swine feeding operation and incubated with 0.03% horseradish powder, 1% mushroom waste powder, and 1% almond hull powder, respectively, in acryl chambers for 14 days. Addition of almond hull powder showed the lowest pH (p < 0.05) and the highest level of total carbon (p < 0.05) among treatments of odor reducing agents. Although addition of odor reducing agents increased the level of phenols (p < 0.05), addition of almond hull powder decreased the level of indoles (p < 0.05). Levels of SCFA and BCFA were higher in almond hull powder than those in control (p < 0.05). Taken together, the results from our current study showed that odor reducing agents can be used for reducing the odor of swine manure by providing fermentable carbohydrates. At $20^{\circ}C$, however, the function of odor reducing agents might be decreased due to lower microbial activity.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.3
• /
• pp.516-524
• /
• 2012

Selective Laser Sintering(SLS) system consists of various element technologies. Main components of the system include a position control system, a speed control system of the roller, and nitrogen atmosphere furtherance for the powdered sintering. Other systems which make the core of the SLS system are build room and the feed room for powder epitaxial, a temperature control system, and a scan path generator for the laser. The powder material for laser sintering is necessary to produce prototypes in Solid Freeform Fabrication(SFF) based on SLS process. This powder material is sintered in powder room using $CO_2$ laser after spreading evenly using roller to reproduce mold via SFF. This study addresses an SFF system by using the SLS process which applies single laser system to enable manufacturing of 3D shape. And to evaluate applicability of the single laser system, experiments were conducted with optimal fabricating process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.311-316
• /
• 2008

Powder type Ag system insert metals were manufactured by ball milling process. The variables of milling process were constant except the milling time. The milling times were selected for 24, 48 and 72 hours. The insert metals made by milling process were evaluated by performing scanning electron microscope, DSC(differential scanning calorimetry) analyses, spreading test and further in terms of wettability test. The selected insert metals that have the good characteristics compared to commercial insert metals were applied to make the brazed joints. The characterizations of those brazed joints were also conducted by microstructural observations. The results indicated that milling time of 48 hours for making powder type insert metals was the best condition showing the good spreadibility, low wetting angle. The brazed joints that applied the 48 hours milled insert metal were very sound condition indicating the stable microstructure in spite of containing small amount of porosity and the microhardness value of the joint was about 138VHN.