• 대한기계학회논문집A
• /
• 제21권7호
• /
• pp.1156-1165
• /
• 1997

Complex modal testing is employed for the in-situ parameter identification of a four-axis active magnetic bearing system while the system is in operation. In the test, magnetic bearings are used as exciters as well as actuators for feedback control. The experimental results show that the directional frequency response function, which is properly defined in the complex domain, is a powerful tool for identification of bearing as well as modal parameters. It is also shown that the position and current stiffnesses can be accurately estimated using the relations between the measured forces, displacements, and currents.

• 한국융합학회논문지
• /
• 제4권4호
• /
• pp.41-48
• /
• 2013

Observer design for system with unknown input was carried out. First, Kalman filter was considered to estimate system state with White noise. With the results of Kalman filter design, state observer, controller properties, including controllability and observability, and the Kalman filter structure and algorithm were also studied. Kalman filter algorithm was applied to Position and velocity measurement based on Kalman filter with white noise, and it was constructed and achieved by programming based on Matlab programming. Finally, observer for system with unknown input was constructed with the help of Gershgorin's disc theorem. With the designed observer, system states was constructed and applied to system with unknown input. By simulation results, estimation performance was verified. In this project, state feedback control theory, observer theory and relevant design procedure, as well as Kalman filter design were understood and used in practical application.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.727-730
• /
• 2007

Coil inductor has been used widely as an electromagnet, because of the high magnetic filed resulting from the voltage applied to the coil. In this study the coils were used in vibration suppression as an actuator. The control system consists of a coil attached in aluminum beam and a permanent magnet set at its bottom. This actuation method is easy to be incorporated into the system and allows significant forces to be applied without contacting with the structure. Three types of coils (cylindrical type, square type, Circular sheet type) were employed in vibration suppression of cantilever beam. The positive position feedback (PPF) controller was applied to the magnet-coil actuator to suppress the first mode of vibration. Experimental results showed that the cylindrical type and square type coil made good vibration suppression efficiency under PPF controller than their eddy current damper. However, there was minimal difference for the circular sheet type coil if compared with its eddy current damper.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.451-456
• /
• 2006

This paper is concerned with the dynamic modeling and controller design for a cylindrical shell equipped with MFC actuators. The dynamic model was derived by using Rayleigh-Ritz method based on Donnel-Mushtari shell theory. The actuator and sensors for the MFC actuator equations were derived based on pin-force model. The boundary conditions at both ends were assumed to be shear diaphragm. After calculating the natural vibration characteristics, the positive position feedback controller was designed to cope with the first two modes. To this end, the equations of motion were reduced to modal equations of motion by considering the modes of interest. The theoretical results show that vibrations can be successfully suppressed.

• 전기학회논문지
• /
• 제67권7호
• /
• pp.840-845
• /
• 2018

BLDC motor is widely used as a servo motor due to high efficiency, high power density, low inertia, and low maintenance. However, BLDC motor generally needs position and velocity sensors to control actuation system. Usually, analog tachometers and encoders have been used for velocity feedback sensors. However, using these types of sensors have problems such as the cost, space, and malfunction. So, This paper is to propose a new velocity measurement method using linear hall-effect and enhanced differentiator for BLDC motor. In order to verify the feasibility of the proposed method, several simulations and experiments are performed. It is shown that the proposed velocity measurement method can satisfy the requirements without using of velocity sensor.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.524-527
• /
• 1995

In most cases, a crane is controlled by an open-loop technique. That is, the controller tries to follow a given velocity profile that is designed to minimize the swing of rope and the transfer time. But such a system is not capable of handling various disturbances such as changing rope length and wind effect. In order to overcome this kind of difficulty, this research focuses on the design of a feedback controller using intelligent techniques such as fuzzy logic and neural network. These intelligent techniques has been emplyoyed in order to represent human knowledge and to imitate human learning. The deveped controllers have been evaluated via computer simulation

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.75-80
• /
• 2007

This paper is concerned with the dynamic modeling and controller design for a cylindrical shell equipped with MFC actuators. The dynamic model was derived by using Rayleigh-Ritz method based on Donnel-Mushtari shell theory. The actuator and sensors for the MFC actuator equations were derived based on pinforce model. The boundary conditions at both ends were assumed to be shear diaphragm. After calculating the natural vibration characteristics, the positive position feedback controller was designed to cope with the first two modes. To this end, the equations of motion were reduced to modal equations of motion by considering the modes of interest. The theoretical results show that vibrations can be successfully suppressed.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2005년도 ICCAS
• /
• pp.241-245
• /
• 2005

Strapdown inertial navigation system (SINS) integrated with astronavigation system (ANS) yields reliable mission capability and enhanced navigational accuracy for spacecrafts. The theory and characteristics of integrated system based on unscented Kalman filtering is investigated in this paper. This Kalman filter structure uses unscented transform to approximate the result of applying a specified nonlinear transformation to a given mean and covariance estimate. The filter implementation subsumed here is in a direct feedback mode. Axes misalignment angles of the SINS are observation to the filter. A simple approach for simulation of axes misalignment using stars observation is presented. The SINS error model required for the filtering algorithm is derived in space-stabilized mechanization. Simulation results of the integrated navigation system using a medium accuracy SINS demonstrates the validity of this method on improving the navigation system accuracy with the estimation and compensation for gyros drift, and the position and velocity errors that occur due to the axes misalignments.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.197-200
• /
• 2001

본 논문에서는 특정한 형태의 제약 즉, 매니퓰레이터의 자유도와 주어진 제약조건의 차원의 차이가 1이며, 매니퓰레이터의 동역학을 작업영역에서의 축차모델로 나타내었을 때, 변환행렬이 단위행렬로 나타나는 제약을 가지는 불확실한 로봇 매니퓰레이터의 위치/힘 추종을 위한 적응제어기를 제안한다. 제안된 제어기는 비선형 좌표변환을 통하여 얻어진 로봇의 축차모델(reduced-order model)을 이용하여 위치제어와 힘제어의 문제를 분리한다. 특히, 비선형 동적 필터를 이용하여 위치의 측정만을 필요로 하며, 적응제어 기법을 통하여 전역 점근적인 안정성을 보장한다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.132.5-132
• /
• 2001

In teleoperation field robotic system such as hydraulically actuated robotic excavator, the maneuverability and convenience is the most important part in the operation of robotic excavator. Particularly the force information is important in dealing with digging and leveling operation in the teleoperated excavator. Excavators are also subject to a wide variation of soil-tool interaction forces. This paper presents a new force reflecting joystick in a velocity-force type bilateral teleoperation system. The master system is electrical joystick and the slave system is hydraulically actuated cylinder with linear position sensor. Particularly Pneumatic motor is used newly in the master joystick for force reflection and the information of the pressure of salve cylinder is measured and utilized as the force feedback signal. Also force-reflection gain greatly affects the ...