• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제11권1호
• /
• pp.101-116
• /
• 1989

Proplast and Porous Polyethylene which have porous structures as low-modulus polymers have been recently used in maxillofacial plastic and reconstructive surgery. The purpose of this study was to compare the response of adajacent tissue, new bone formation and stability after augmentation by differen methods of subperiosteal graft using proplast and purous polythylene in rabbit mandible. The augmentation procedure was carried out by dividing into two groups, A and B. A group consisted of subperiosteal graft on the cortex, and the other B group was made up only graft following artificial decortication in the mandibular body of rabbit. The experimental animals were sacrificed on the 1st, 2nd, 4th and 8th week after grafting for macroscopic and light microscopic examination. The samples extracted at the 6th postgrafting week were also used for biometric testing and scanning electron microscopic examination. The results obtained from this study were as follows : 1. Macroscopically, infection of graft site, deformation and migration of graft material were not observed in all experimental groups. 2. B group showed more rapid and increased bone formation and the greater stability than A group, and tissue response was similar to each other. 3. In the tissue response, macrophages and cellular infiltrations were observed in Proplast group, but few in PHDPE group. 4. In bone formation of A group, Proplast group showed no bone formation until the 8th week, but PHDPE group showed small quantity of osteoid tissue from the 2nd week and appositional bone growth with new bone formation at the 8th week. 5. In bone formation of B group, both Proplast and PHDPE group showed bone formation, but PHDPE group showed more rapid and larger bone formation. 6. In pattern of bone formation, Proplast group mainly showed appositional bone growth pattern connected with graft site. On the other hand, PHDPE group showed mixed pattern of new bone formation in the pore connective tissue with appositional bone growth from graff site. 7. The maximum mean values of shear stress were serially $111.3gf/mm^{2}$ in PHDPE of B group, $84.8gf/mm^{2}$ in PHDPE of A group, $32.9gf/mm^{2}$ in Proplast B group, and $15.7gf/mm^{2}$ in Proplast of A group. From above results, It was suggested that the capacity of bone formation and stability between bone and graft material were dependent on the pore size and structure of graft material itself, the state of graft site and tissue response.

• 폴리머
• /
• 제38권4호
• /
• pp.530-534
• /
• 2014

다양한 기공도를 갖는 폴리에틸렌 분리막은 리튬이차전지의 격리막과 마이크로필터로 사용되고 있다. 폴리에틸렌 분리막을 대용량 리튬이차전지의 격리막에 응용하기 위해서는 고다공성 분리막의 제조가 요구된다. 본 연구에서는 열유도 상분리 공정으로 고다공성 폴리에틸렌 분리막을 제조하는데 있어, BET가 무독성 희석제로 사용 가능한지 여부를 실험하였다. 폴리에틸렌/BET 혼합물의 UCST-거동을 관찰하여 BET가 폴리에틸렌 다공막 제조용 희석제로 사용 가능함을 확인하였다. 폴리에틸렌/BET 혼합물로부터 제조된 분리막이 같은 조성에서 폴리에틸렌/파라핀 오일로부터 제조된 분리막에 비해 1.8배 높은 기공도를 나타내었다.

• 폴리머
• /
• 제35권4호
• /
• pp.296-301
• /
• 2011

본 연구는 고내구성을 가진 고분자 전해질막을 제조하는 것으로 연료전지에 적용하기 위하여 poly(vinyl alcohol)을 주사슬부로 하여 poly(styrene sulfonic acid-co-maleic acid) (PSSA-MA)를 다공성 polyethylene(PE) 막에 함침시켜 막을 제조하였다. 제조된 막을 함수율, 접촉각, FTIR, 이온교환용량, 이온전도도 메탄올 투과도 열 중량분석, 탄성계수 등의 측정을 통해 친수성 고분자가 함침된 막의 특성평가를 실시하였다. 접촉각 측정과 FTIR 분석을 통해 PE 막에 함침된 막에서의 친수성기의 존재를 확인하였다. PSSA-MA의 함량이 10 wt% 함침된 막의 경우, 이온교환 용량은 Nafion 115의 0.91보다 향상된 1.2 meq./g dry membrane을 얻었다. 또한 탄성계수의 경우 PE 막에 비하여 3~3.6 배 높은 강도를 나타내었으며, 함수율과 메탄올 투과 실험을 통해 PSSA-MA의 함량이 늘어남에 따라 높은 치수안정성과 낮은 메탄올 투과결과를 확인하였다.

• 멤브레인
• /
• 제31권5호
• /
• pp.333-342
• /
• 2021

유연한 전기변색 소자(electrochromic device, ECD)는 스마트 윈도우 등 다양한 분야에서 응용이 기대되는 유망한 기술이다. 고분자 전해질은 유연한 ECD의 탈-변색 성능 및 물리적 안정성을 결정하는 중요한 구성요소이다. 본 연구에서는 효과적인 유연한 ECD 제조 및 내구성 향상을 위해 치수안정성이 우수한 세공충진 고분자 전해질 멤브레인(PFPEM)을 개발하였다. 저렴하며 물리적 및 화학적 안정성이 우수한 폴리에틸렌 재질의 다공성 지지체의 세공에 접착력이 우수한 polyvinyl acetate와 이온전도도를 향상시킬 수 있는 polyethylene glycol을 사용하여 제조한 고분자 전해질을 충진하였다. 제조된 PFPEM의 최적 리튬 염(LiTFSI) 함량은 약 27 wt%에서 결정되었으며 우수한 치수안정성와 접착 강도 그리고 종래의 고분자 전해질에 근접하는 이온전도 특성을 가지고 있음을 확인하였다. 다공성 지지체의 사용으로 가시광 투과율이 저하되었으나 변색 상태에서는 오히려 장점으로 작용할 것으로 전망되었다.

• 대한두개안면성형외과학회지
• /
• 제11권2호
• /
• pp.85-90
• /
• 2010

Purpose: The goals of a blow-out fracture reconstruction are to restore the osseous continuity, provide support for the orbital contents and prevent functional and anatomic defects. Over the past several years, a range of autogenous and synthetic implants have been used extensively in orbital reconstructions. None of these implants have any absolute indications or contraindications in certain clinical settings. However, in extensive blow-out fractures, it is difficult to restore support of the orbital contents, which can cause more complications, such as enophthalmos. This study examined the clinical outcomes of extensive or comminuted blow-out fractures that were reconstructed by the simultaneous use of a titanium mesh plate and $Medpor^{(R)}$. Methods: Eighty six patients with extensive orbital fractures, who were admitted between March 1999 and February 2007, were reviewed retrospectively. The patients' chart and CT were inspected for review. Twenty three patients were operated on with both a titanium mesh plate (Matrix MIDFACE pre-formed orbital plate, Synthes, USA) and $Medpor^{(R)}$ (Porex, GA, USA). The patients underwent pre-operative CT scans to evaluate the fracture site and measure the area of the fracture. A transconjunctival approach was used, and titanium mesh plates were inserted subperiosteally with screw fixation. $Medpor^{(R)}$ was inserted above the titanium mesh plate. The patients were evaluated post-operatively for enophthalmos, diplopia, sensory disturbances and eyeball movement for a period of at least 6 months. Results: No implant-related complications were encountered during the follow-up period. Enophthalmos occurred in 1 patient, 1 patient had permanent sensory disturbance, and 3 patients complained of ocular pain and fatigue, which recovered without treatment. Although there were no significance differences between groups, the use of 2 implants had fewer complications. Therefore, it can be an alternative method for treating blow out fractures. Conclusion: The use of both a titanium mesh plate and $Medpor^{(R)}$ simultaneously may be a safe and acceptable technique in the reconstruction of extensive blow-out fractures.

• 한국세라믹학회지
• /
• 제35권9호
• /
• pp.958-968
• /
• 1998

Porous silica ceramics were prepared using DCCA(Drying Control Chemical Additives) Such as uncharged polymer(Polyethylene glycol) and protein (Lipase) under H2O/Low-grade TEOS=10 C2H5OH/Low-grade TEOS=1 HC1/Low=grade TEOS=0.01 After Plain which doesn't added DCCA and samples of 11 sorts which varied molecular weight of PEG(Mw=600, 1000, 2000) quantity of Lipase and concentration of wat-er were synthesized gellation time and thermal analysis were investigated. After heat-treated at 600, cry-stal structures analyses of SiO2 polymer and characteristics of pores were investigated. Gellation time was retarded about 2-6 times as compared with plain resulting in addition of DCCA and crystal structures ex-hibited amorphous state. Moreover as increase of water a short gellation time was obtained. The samples added PEG showed increase of specific surface areas up to 20-40% and had micropores while those of Lipase were decreased about 90% and showed broad pore size distribution.

• 한국세라믹학회지
• /
• 제30권10호
• /
• pp.838-844
• /
• 1993

To control the pore size of silcia gel, formamide (FA), N,N-dimethyl formamide (DMF), polyethylene glycol (PEG) and polyacrylic acid (PAA) were added in the sol-gel process from starting solution with tetramethyl orthosilicate (TMOS). The gels were characterized using porosimeter, TG-DTA and SEM. As a result, the more contents of FA and PAA was increased the more gelation time was decreased, also the more contents of DMF and PEG was increased the more gelling time was increased. The mean pore size of gels was larger in the order of PAA, DMF, FA and PEG. And the mean pore size of porous silica glass was 59.0$\AA$, 31.5$\AA$, 29.9$\AA$ and 29.0$\AA$, respectively, heated at 75$0^{\circ}C$/100$0^{\circ}C$.

• 분석과학
• /
• 제30권2호
• /
• pp.75-81
• /
• 2017

5-methylthioninhydrin (5-MTN) is an amino acid sensitive reagent used for the development of latent fingermarks deposited on porous surfaces such as paper and wood. The present study demonstrates that the 5-MTN can be used as a latent footwear impression enhancement reagent, by reacting with trace multivalent metal ions, which are the main components of the latent footwear impression. 5-MTN and L-alanine complex (MTN-ALA) used for the latent footwear impression development was prepared, by mixing $4.5{\times}10^{-3}M$ 5-MTN (in methanol) and $4.5{\times}10^{-3}M$ L-alanine (in methanol) in 1:1 ratio, and keeping undisturbed at room temperature for 24 h. The latent footwear impressions were deposited on white and black non-porous surfaces (glass plate, polyethylene panel, polypropylene panel, acryl panel, polyvinyl chloride (PVC) panel, poly(methyl methacrylate) (PMMA) panel, acrylonitrile-butadiene-styrene (ABS) panel, tile), and a semi-porous surfaces (painted wood). The latent footwear impressions on these surfaces were treated with MTN-ALA complex by spraying. The fluorescence of footwear impressions (occurred due to the reaction between MTN-ALA and metal complexes) was observed under a 505 nm forensic light source and an orange barrier filter. The enhancement of latent footwear impression was achieved from black surfaces without any blurring. However, the fluorescence (enhancement) of footwear impression was not observed on the white PVC, PMMA, and ABS surfaces, because the incident light interfered and reflected on the surface. The sensitivity of MTN-ALA was superior to 2,2'-dipyridil, which is a representative non-fluorescing footwear impression enhancement reagent, and similar to 8-hydroxyquinoline, which is a representative fluorescing footwear impression enhancement reagent.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.645-649
• /
• 2009

Liquid desiccant cooling technology can supply cooling by using waste heat and solar heat which are hard to use effectively. For compact and efficient design of a dehumidifier, it is important to sustain sufficient heat and mass transfer surface area for water vapor diffusion from air to liquid desiccant on heat exchanger. In this study, the plate type heat exchanger is adopted which has extended surface, and hydrophilic coating and porous layer coating are adopted to enhance surface wettedness. PP(polypropylene) plate is coated by porous layer and PET(polyethylene terephthalate) non-woven fabric is coated by hydrophilic polymer. These coated surfaces have porous structure, so that falling liquid film spreads widely on the coated surface foaming thin liquid film by capillary force. The temperature of liquid desiccant increases during dehumidification process by latent heat absorption, which leads to loss of dehumidification capacity. Liquid desiccant is cooled by cooling water flowing in plate heat exchanger. On the plate side, the liquid desiccant can be cooled by internal cooling. However the liquid desiccant on extended surface should be moved and cooled at heat exchanger surface. Optimal mixing and distribution of liquid desiccant between extended surface and plate heat exchanger surface is essential design parameter. The experiment has been conducted to verify effective surface treatment and distribution characteristics by measuring wall side flow rate and visualization test. It is observed that hydrophilic and porous layer coating have excellent wettedness, and the distribution can be regulated by adopting holes on extended surface.

• 대한화장품학회지
• /
• 제30권2호
• /
• pp.189-195
• /
• 2004

카본 블랙은 매우 낮은 밀도로 화장품에는 사용되지 않고 있지만 독성이 없고 안정한 물리적 특성과 검은색의 특성으로 이용 가치가 있다고 사료되는 바이다. 본 연구에서는 TEOS, a) PEO/ lecithin, b) PEO/polyethylene glycol, c) lecithin/polyethylene을 ethanol/water 수용액상에서 계면활성제를 탄화시켜 sol-gei반응에 의해 meso-porous silica샘플을 얻었고 N2 조건하 50$0^{\circ}C$에서 열처리된 organic-inorganic hybrid silica를 합성하였다. Pore안에 카본 블랙을 함유하는 meso-porous silica는 친수성, 소수성 용매에서 모두 좋은 분산성을 보여준다. 이 샘플은 BET에 의해 specific surface area (750$m^2$/g)과 pore size (4-6 nm)이고, XRD측정으로 pore structure (cylindrical type)를, 샘플의 SEM촬영으로 morphology(0.1-0.5$\mu\textrm{m}$ 입자 크기를 갖는 spherical powder)를 갖는다는 것을 알아냈다. 이렇게 합성한 카본-실리카 블랙 컬러를 마스카라에 적용하면 일반적으로 마스카라에 사용되던 블랙 컬러 사용시 보다 좀더 검은색을 보여주는 것은 물론이고 우수한 분산성도 갖는다. 무엇보다 이 파우더의 밀도 조절이 가능하여 마스카라 뿐 만 아니라 모든 화장품에의 사용이 가능하다.