• 청정기술
• /
• 제29권3호
• /
• pp.178-184
• /
• 2023

전이금속 칼코젠화물은 소듐 이차전지의 음극재로서 높은 이론 용량을 가지나 충·방전 과정에서 큰 부피 팽창으로 인해 짧은 수명 특성을 보이며, 낮은 전기전도도로 인해 출력 특성을 저하시킨다는 문제가 있다. 이를 해결하기 위해, 본 연구에서는 분무열분해와 후 열처리 공정을 통해 다공성의 CNT ball과 (Ni,Co)Se₂ 나노결정이 복합된 구조체를 합성하였으며, 이를 소듐 이차전지의 음극에 적용시켜 전기화학적 특성을 평가하였다. 합성된 소재는 분무열분해 동안 Polystyrene(PS) 나노비드의 분해로 인해 다공성 구조를 형성하여 충방전 과정에서 발생하는 부피팽창을 효과적으로 수용하였으며, CNT 소재와의 복합화를 통해 전기화학적 성능을 향상시킬 수 있었다. 이로 인해 다공성 구조의 (Ni,Co)Se₂-CNT 복합소재는 0.2 A g^-1의 전류밀도에서 698 mA h g^-1의 높은 초기 방전용량을 보였으며, 100 사이클 후 400 mA h g^-1의 방전용량을 유지함을 보였다.

• 에너지공학
• /
• 제2권3호
• /
• pp.293-299
• /
• 1993

용융탄산염연료전지(MCFC)용 다공성 Ni 양극에 3~10 wt% Al를 첨가하여 tape casting 법으로 제조된 Ni-Al 양극의 전기화학적성능 및 구조적안정성이 조사되었다. 본 연구에서 제조된 양극의 전기화학적 성능이 $650^{\circ}C$, MCFC 양극분위기(80% H$_2$＋20% $CO_2$)를 모사한 half-cell 에서 양분극 특성으로 평가되었는데, 전류밀도 150 ㎃/$\textrm{cm}^2$ 에서의 분극전압은 약 100 ㎷로 실용전지의 양극으로서 가능성을 보였다. Ni-Al 양극의 소결과 creep에 대한 저항성은 Ni 양극에 비해 증가되었는데, 이는 Ni 입자 표면에 형성된 $Al_2$O$_3$의 영향으로 판단되었다.

• 방사성폐기물학회지
• /
• 제20권4호
• /
• pp.383-398
• /
• 2022

The electrochemical behavior was investigated during the electrolysis of nickel oxide in LiCl-Li₂O salt mixture at 650℃ by changing several components. The focus of this work is to improve anode design and shroud design to increase current densities. The tested components were ceramic anode shroud porosity, porosity size, anode geometry, anode material, and metallic porous anode shroud. The goal of these experiments was to optimize and improve the reduction process. The highest contributors to higher current densities were anode shroud porosity and anode geometry.

• Korean Chemical Engineering Research
• /
• 제56권4호
• /
• pp.561-567
• /
• 2018

본 연구에서는 리튬이온전지 실리콘 음극소재의 사이클 안정성 향상을 위해 실리콘/탄소 음극소재의 전기화학적 특성을 조사하였다. Tetraethyl orthosilicate (TEOS) 로부터 스토버법 및 마그네슘 열 환원법을 통하여 다공성 실리콘을 제조하고, 제조된 다공성 실리콘과 피치의 질량비에 따라 실리콘/탄소 음극소재를 제조하였다. 실리콘/탄소 음극소재의 물리적 특성은 XRD와 TGA를 통해 분석하였다. 1.0 M $LiPF_6$ (EC : DEC = 1 : 1 vol%) 전해액에서 실리콘/탄소 음극소재의 충 방전 사이클, 율속, 순환전압전류, 임피던스 테스트를 통해 전기화학적 특성을 조사하였다. 제조된 실리콘/탄소 음극소재 실리콘 : 탄소 = 5 : 95 일때 453 mAh/g의 향상된 용량을 나타내었으며, 사이클 성능 또한 두 번째 사이클 이후 30 사이클까지 매우 우수한 사이클 안정성을 나타냄을 확인하였다.

• 한국연소학회지
• /
• 제15권3호
• /
• pp.8-14
• /
• 2010

Fuel processing systems which convert fuel into rich gas (such as stream reforming, partial oxidation, autothermal reforming) need high temperature environment ($600{\sim}1,000^{\circ}$). Generally, anode-off gas or mixture of anode-off gas and LNG is used as input gas of fuel reformer. In order to make efficient and low emission burner system for fuel reformer, it is necessary to elucidate the combustion and emission characteristic of fuel reformer burner. The purpose of this study is to develop a porous premixed flat ceramic burner that can be used for 1~5 kW fuel cell reformer. Ceramic burner experiments using natural gas, hydrogen gas, anode off gas, mixture of natural gas & anode off gas were carried out respectively to investigate the flame characteristics by heating capacity and equivalence ratio. Results show that the stable flat flames can be established for natural gas, hydrogen gas, anode off gas and mixture of natural gas & anode off gas as reformer fuel in the porous ceramic burner. For all of fuels, their burning velocities become smaller as the equivalence ratio goes to the lean mixture ratio, and a lift-off occurs at lean limit. Flame length in hydrogen and anode off gas became longer with increasing the heat capacity. In particular, the blue surface flame is found to be very stable at a very lean equivalence ratio at heat capacity and different fuels. The exhausted NOx and CO measurement shows that the blue surface flame represents the lowest NOx and CO emissions since it remains very stable at a lean equivalence ratio.

• 한국재료학회지
• /
• 제22권1호
• /
• pp.1-7
• /
• 2012

Thin film electrode consisting purely of porous anodic tin oxide with well-defined nano-channeled structure was fabricated for the first time and its electrochemical properties were investigated for application to an anode in a rechargeable lithium battery. To prepare the thin film electrode, first, a bi-layer of porous anodic tin oxides with well-defined nano-channels and discrete nano-channels with lots of lateral micro-cracks was prepared by pulsed and continuous anodization processes, respectively. Subsequent to the Cu coating on the layer, well-defined nano-channeled tin oxide was mechanically separated from the specimen, leading to an electrode comprised of porous tin oxide and a Cu current collector. The porous tin oxide nearly maintained its initial nano-structured character in spite of there being a series of fabrication steps. The resulting tin oxide film electrode reacted reversibly with lithium as an anode in a rechargeable lithium battery. Moreover, the tin oxide showed far more enhanced cycling stability than that of powders obtained from anodic tin oxides, strongly indicating that this thin film electrode is mechanically more stable against cycling-induced internal stress. In spite of the enhanced cycling stability, however, the reduction in the initial irreversible capacity and additional improvement of cycling stability are still needed to allow for practical use.

• 한국세라믹학회지
• /
• 제43권11호
• /
• pp.746-750
• /
• 2006

NiO films and Ru co-sputtered NiO films were deposited by reactive magnetron sputtering for micro-solid oxide fuel cell anode applications. The deposited films were reduced to form porous films. The reduction kinetics of the Ru doped NiO film was more sluggish than that of the NiO film, and the resulting microstructure of the former exhibited finer pore networks. The possibility of using the films for the anodes of single chamber micro-SOFCs was investigated using an air/fuel mixed environment. It was found that the abrupt increase in the resistance is suppressed in the Ru co-sputtered film, as compared to undoped film.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 D
• /
• pp.1547-1549
• /
• 1999

As a preliminary experiment for the development of anode-supported tubular cell with proper porosity, we have investigated the anode substrate and the electrolyte-coated anode tube. The anode substrate was manufactured as a function of carbon content in the range of 20 to 50 vol.%. As the caron content increased, the porosity of the anode substrate increased slightly and the carbon content with proper porosity was obtained at 30 vol.%. The anode tube was fabricated by extrusion process and the electrolyte layer was coated on the anode tube by slurry dipping process. The anode-supported tube was cofired successfully. Their sintered property and microstructure were examined and the porosity of the anode tube was 35%. From the gas permeation test, the anode tube was found to be porous enough for gas supply. On the other hand, the anode-supported tube with electrolyte layer indicated a very low gas permeation rate. This means that the coated electrolyte was dense. Based upon these experimental results. we will fabricate and test the anode-supported tubular cell.

• 한국세라믹학회지
• /
• 제54권5호
• /
• pp.438-442
• /
• 2017

This paper reports the facile synthesis of microlamella-structured porous copper (Cu)-oxide-based electrode and its potential application as an advanced anode material for lithium-ion batteries (LIBs). Nanowire-like Cu oxide, which is created by a simple thermal oxidation process, is radially and uniformly formed on the entire surface of Cu foam that has been fabricated using a combination of water-based slurry freezing and sintering (freeze casting). Compared to the Cu foil with a Cu oxide layer grown under the same processing conditions, the Cu foam anode with 63% porosity exhibits over twice as much capacity as the Cu foil (264.2 vs. 131.1 mAh/g at 0.2 C), confirming its potential for use as an anode electrode for LIBs.

• 한국표면공학회지
• /
• 제27권3호
• /
• pp.166-175
• /
• 1994

The effect of Co addition on the electrochemical performance and structural stability of porous Ni anode for molten carbonate fuel cell(MCFC) was evaluated by the anodic polarization and the sintering test in the simulated MCFC anode condition ($650^{\circ}C$, 80% $H_2$+20%$CO_2$). The anode current density ranged from 110mA/$cm^2$ to 144mA/$cm^2$ was obtained at +100mV overpotential by additions of Co up to 10 wt.%. The sintering resistance of Ni-Co anodes was higher than that of the pure Ni anode. The increase of sintering resistance seemed to be to the lower diffusion coefficient of Co than that of Ni.