• Journal of the Korean Geotechnical Society
• /
• v.19 no.2
• /
• pp.65-74
• /
• 2003

Most of land reclamation projects are being implemented along the south and west coastal lines of the Korean Peninsula. The earth structures and in-ground LNG tank, and buildings can be constructed using artificial freezing method on the reclaimed land to control the uplift pressure caused by capillary forces. In this study, upon freezing a saturated soil in a closed-system from the top, a considerable frost heaving pressure was developed. Decomposed granite soils, silty soil, and sandy soil were used in the laboratory freeze test which is sometimes subjected to thermal gradients under closed-systems. A major concern has been the ability to predict the frost heaving pressure over the results of relatively short-term laboratory tests. The frost heaving pressure arising within the soil samples and the temperature of the samples inside were monitored with time elapse. The degree of saturation versus heaving pressure curve is presented for each soil sample and the maximum pressure is closely related to this curve. TDR apparatus was used to measure the volumetric water content by the measurement of unfrozen water contents of frozen soils. Unfrozen water increased in soils containing a high percentage of fine-grained particles. In fine-grained soils with strong attractive farces between soil grains and water molecules, additional water is attracted into the pores leading to further volume changes and ice segregation.

• Journal of the Korea Concrete Institute
• /
• v.20 no.2
• /
• pp.131-138
• /
• 2008

Humidity and strain were estimated for understanding the relation between humidity change by self-desiccation and shrinkage in high-performance concrete with low water binder ratio. Internal humidity change and shrinkage strain were about 10%, 4% and $320\times10^{-6}$, $120\times10^{-6}$ respectively on concrete with water binder ratio 0.3, 0.4 and from the results, humidity change and shrinkage represented the strong linear relation regardless of mixture. For specifying the relation on internal humidity change and autogenous shrinkage strain, shrinkage model was established which is driven by capillary pressure in pore water and surface energy in hydrates on the assumption of a single network and extended meniscus in pore system of concrete. This model and experimental results had a similar tendency so it would be concluded that the internal humidity change by self-desiccation in HPC originated in small pores less than 20 nm, therefore controlling plan on autogenous shrinkage might be focused on surface tension of water and degree of saturation in small pore.

• Journal of the Korea Institute of Building Construction
• /
• v.13 no.4
• /
• pp.407-415
• /
• 2013

The purpose of this research is to verify the performance of hardening accelerator in cement paste through mechanical performance evaluation and micro structure analysis on hardening accelerator for development of super high early strength concrete. The research results showed that hardening accelerator produced $Ca(OH)_2$ when hydrated with cement, enhancing the degree of saturation of Ca ion by using differential thermal analysis. Moreover, porosity was reduced rapidly as capillary pores were filled by hydration products of $C_3S$. According to the experiment using hydration measurement testing, when 1% and 3% of accelerator were mixed, hydration rate increased toward the second peak point compared to high early strength cement, before the first peak point disappeared. It turned out that adding accelerator accelerated the hydration rate of cement, especially $C_3S$. The shape of C-S-H is shown depending on the amounts of accelerator added and the production and age of $Ca(OH)_2$ by using SEM to observes hydration products. Therefore, it's evident that hardening accelerator used in this research increases amounts of $Ca(OH)_2$ and accelerates $C_3S$, it is effective for the strength development on early age.

• Journal of the Korea Institute of Building Construction
• /
• v.17 no.3
• /
• pp.211-217
• /
• 2017

The objective of this study is to seek a reliable mixture proportion for magnesium potassium phosphate composite(MKPC) mortars with a near-neutral pH value (below 9.5) and a relatively good compressive strength exceeding 30MPa. The main parameter selected was the molar ratios($M_{mp}$) of $MgO-to-KH_2PO_4$ which varied from 30.4 to 3.4. The setting time of the MKPC mortars tended to shorten with a decrease in $M_{mp}$ value. With regard to the strength development ratio normalized by the 28-day strength, the ranges measured in the mortars with an $M_{mp}$ below 7.9 were 50~61% at 1 day and 60~73% at 3 days, indicating a highly rapid early-strength development. With a decrease in $M_{mp}$, the formation of struvite-K crystal identified as a primary hydration product increased, which led to the decrease of the macro-capillary pores in micro-structures. For achieving the targeted requirements for pH value and compressive strength, the $M_{mp}$ needs to be selected as below 5.1.

• Journal of Korean Society of Forest Science
• /
• v.99 no.4
• /
• pp.534-545
• /
• 2010

To examine 1) rainfall pattern (i.e., type and intensity) regulating surface erosion on hillslopes in postwildfire area and 2) its effect on variation in sediment yield along the gradient of severity wildfire regimes and elapsed years, we surveyed the amount of sediment yield with respect to daily or net-effective rainfall in 9 plots in eastern coastal region, Republic of Korea. Before field investigation, all plots classified into three groups: low-, mixed- and high-severity wildfire regimes (3 plots in each group). We found that, with decreasing wildfire regimes and increasing elapsed years, the rainfall type regulating surface erosion changed from daily rainfall to net-effective rainfall (considering rainfall continuity) and its intensity increased continuously. In general, wildfires can destroy the stabilized forest floors, and thus rainfall interception by vegetation and litter layer should be reduced. Wildfires can also decrease soil pores in forest floors, and thus infiltration rates of soil are reduced. These two processes lead to frequent occurrence of overland flows required to surface erosion, and sediment yields in post-wildfire areas should increase linearly with increasing rainfall events. With the decreasing severity wildfire regimes and the increasing elapsed years, these processes should be stabilized, and therefore their sediment yields also decreased. Our findings on variations in sediment yields caused by the wildfire regimes and the elapsed years suggest understanding of hydrogeomorphic and ecologic diversities in post-wildfire areas, and these should be carefully examined for both watershed management and disaster prevention.

• Journal of Ocean Engineering and Technology
• /
• v.19 no.5 s.66
• /
• pp.43-49
• /
• 2005

This paper is to investigate the effect of corrosion by acoustic emission method in tensile loading and the adhesiveness between substrate and coating layer. The powders used are Zn and Amdry625, respectively. They are coated on brass alloy substrate. AE signals of Zn and Amdry625 coating layer increase drastically in strain $2\%$. However, those of Zn specimen have more than those of Amdry625 specimen. When the specimens executed the corrosion test under $3.5\%$ NaCl solution for 500, 1000 hours, the salt solution penetrated into the surface of the substrate through the pores of the coating layer. As a result, corrosion production formed on the surface of the substrate. The adhesiveness between coating layers is weakened by the polarization and corrosion itself. The AE event, count, and energy of corroded coating specimens decrease, compared to specimens without corrosion. The results are summarized as follows : 1. In the tensile tests, the time that it took to start and develop the cracks and exfoliations between the surface of the substrates and the plasma spray coatings were different according to the type of plasma sprayed material, which are Zn and Amdry625. These phenomena were obvious at the strain rate 1 to $5\%$, and few available data were found after that stage. 2. The specimens with Zn coating showed the characteristics of crack, according to the changes of the tensile strength applied on the substrates while those with Amdry625 showed exfoliation as a result of low adaptation to the tensile strength. 3. The anti-corrosion specimens showed that the adhesive properties between the substrate and the plasma spray coating were strong in the order of Zn, Amdry. It showed that Corroded specimens cracked or exfoliated easily, even with the small energy, because those had a comparatively weakened adhesive property, due to corrosion. 4. Zn specimen showed no corrosion phenomena on the surface of the substrates, because they had the function of sacrifice anode however, Amdry625 specimen showed the corrosion, because it did not have that function.

• Journal of Biomedical Engineering Research
• /
• v.21 no.3 s.61
• /
• pp.295-301
• /
• 2000

It is known that among many factors, relative micromotion at bone/implant interfaces can hinder bone ingrowth into surface pores of an implant. Loading conditions, mechanical properties of spinal materials, friction coefficients at the interfaces and geometry of spinal segments would affect the relative micromotion and spinal stability. A finite clement model of the human lumbar spine segments (L4-L5) was constructed to investigate the mechanical sensitivity at the interfaces between bone and cage. Relative micromotion. Posterior axial displacement. bone stress, cage stress and friction force were predicted in changes of friction coefficients, loading conditions. bone density and age-related material/geometric properties of the spinal segments. Relative micromotion (slip distance in a static loading means relative micromotion in routine activity) at the interfaces increased significantly as the mechanical properties of cancellous bone, annulus fibers or/and ligaments decrease or/and as the friction coefficient at the interfaces decreases. The contact normal force at the interfaces decreased as cancellous bone density decreases or/and as the friction coefficient increases A significant increase of slip distance at anterior annulus occurred with an addition of torsion to compressive preload. Relative micromotion decreased with an increase of disc area. In conclusion. relative micromotion, stress response. Posterior axial displacement and contact normal force are sensitive to the friction coefficient of the interfaces, bone density, loading conditions and age-related geometric/material changes.

• The Journal of Korean Academy of Prosthodontics
• /
• v.31 no.3
• /
• pp.317-349
• /
• 1993

This study investigated the effect of filler particle size and weight% on mechanical properties of dental core porcelain. In alumina, variation in particle size and weight% and in zirconia, variation in weight%, all specimens were tested three-point bending strength, transmittance, thermal expansion coefficient, porosity and shrinkage and observed with SEM and analysed with X-ray diffractometer. In order to develop shrink-free porcelain, after firing alumina only, glass wasinfiltrated. And aluminum was added to alumina with the expanding character of aluminum oxidize into alumina, and was followed by second firing of glass infiltration procedure. Then mechanical properties were observed. The results of this study were obtained as follows. 1. The bending strength of zirconia was higher than that of alumina, and $5{\mu}m$ alumina had highest strength in variation of particle size of alumina. Except for $5{\mu}m$ alumina, increased with weight%, bending strength increased up to 80% and decreased at 90%. In case of glass infiltration, bending strength was slight higher than 80% and 90% of $5{\mu}m$ alumina. 2. Transmittance increased with increase of shrinkage, decrease of porosity, and with increase of filler size and had no direct correlation with weight%. 3. Thermal expansion coefficient of alumina group was $7.42\sim8.64\times10^{-6}/^{\circ}C$ and that of zirconia group was $9.83\sim12.11\times10^{-6}/^{\circ}C$ and the latter was higher than the former. 4. In x-ray diffraction analysis, alumina group and zirconia group increased $Al_2O_3$ peak and $t-ZrO_2$ peak with increase of weight%. The second phase(cristobalite peak) was observed in zirconia 40% group. 5. Porosity of zirconia was lower than that of alumina and $5{\mu}m$ alumina group had many pores with SEM. In case of low filler content, fracture occurred in glass and high filler content, in glass and filler. In case of aluminum addition to alumina, small oxidised aluminum was observed. 6. Zirconia group had high shrinkage than alumina group, and mixed group of alumina group had high shrinkage. In case of glass infiltration, shrinkage decreased and aluminum addition to alumina group was almost shrink-free.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.1
• /
• pp.82-89
• /
• 2016

And by entering into an aging society with economic growth "beautiful and healthy desire to live', aesthetics industry as promote interest in 'Anti-aging' is emerging as a promising business increased significantly the skin care market. However, the management of the hospital or the temporal order to receive professional care providers, spatial, and cost constraints caused many companies to solve this problem began to approach the Home Care Area. Global trends in personal skin care market has been activated, the domestic has been activated at low cost, private market due to the recession. We have performed this test in order to develop a skin care device for home in order to compensate for this point.In this paper, we develop a low-level laser to create a personal skin care products and sought to incorporate them into the skin cosmetic.Expand the pores by using the low-level laser to the skin by to the dermal layer of the skin was penetrated aim experiment the ampoule, and by a comparison of the medical low-level laser reliability and determine the effectiveness or absence of the performance and efforts to commercialize.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.12
• /
• pp.5438-5442
• /
• 2011

In order to use as weight-reduced sintered parts for automobiles, mechanical properties of sintered compacts of 2712 Al-alloys containing 0, 10, 20, and 33% ceramics, respectively, were investigated in this study. (1)Regardless of ceramic contents, all sintered compacts possessed 4~7% pores. (2)After aging the compacts sintered for 12 minutes, tensile strength of the 2712 Al-alloys containing 0, 10, 20, and 33% ceramics was 165, 260, 256, and 166 N/$mm^2$, respectively, whereas those aged after sintering for 30 minutes exhibited the tensile strength of 186, 229, 219, and 202 N/$mm^2$, respectively. In addition, the 2712 sintered compact containing 10% ceramics showed the maximum elongation of about 3.6%, (3)After aging the 10% ceramic-containing sintered compacts reached a maximum apparent hardness ($H_RF$) of 97. (4)The minimum wear volume ($174{\times}10^{-3}mm^3$) was shown in the 10% ceramic-containing 2712 sintered compact after aging. From these results, the 2712 sintered compact containing 10% ceramics thought to be the most suitable one for the fabrication of aluminum engine part.