• Journal of the Korean Ceramic Society
• /
• v.51 no.5
• /
• pp.406-412
• /
• 2014

In this study, flat-tubular-type alumina filters were manufactured using alumina powder of two sizes ($2.4{\mu}m$ ALM-44 and $0.4{\mu}m$ AP 400) by an extrusion process. The manufactured alumina filter was sintered at $1200-1600^{\circ}C$ for 1 h. As particle size increased, the largest pore size, average pore size and porosity increased; but density and linear shrinkage decreased. The alumina filter fabricated using ALM-44 powder sintered at $1500^{\circ}C$ was confirmed as the best water treatment filter after investigation of the bending strength, water permeability and impurity-removal efficiency of the experimental filters. This flat-tubular-type alumina filter is expected to be useful not only for direct water treatment, but also for use as a support filter during coating processes, to control pore size.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.13 no.6
• /
• pp.463-499
• /
• 2011

Control of ground water is one of the most important factors for long-term operation of tunnel because most tunnels are located under the ground water level. In case of a drainage tunnel, there is no pore water pressure on the lining when the drainage system is properly working. After long-term operation, however, residual pore water pressure can be developed on the lining due to the deterioration of the drainage system. In this study, the water pressure distribution under obstruction condition of drainage material and conduit on the tunnel is numerically investigated using the ICFEP program and compared with the current value being applied to the residual water pressure for rational application plan of residual water pressure on the tunnel linings.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2004.05a
• /
• pp.207-210
• /
• 2004

The pore-filled anion-exchange membranes were prepared in this study with an asymmetric poly(vinylidene fluoride)(PVDF) membrane as a nascent membrane and poly(vinylbenzyl chloride)(PVBCl) as a polyelectrolyte. The solution of PVBCI having the chloromethylate aryl ring of 80 percents and 1,4-diaminobicyclo [2,2,2]octane(DABCO) was made with the solvent of tetrahydrofuran(THF) and N,N-Dimethylformamide(DMF), which is in the rotio of 8:2. A new preparation method in this study, i.e. in-situ crosslinking, enabled us to produce the pore-filled membranes without change of size, and to control the properties of final membrane with various degree of cross-linking. From the result of surface morphologies of SEM and AFM the polyelectrolyte exists in the pores of nascent membrane as a certain configuration. From the investigation of the solvent affecting much to the permeability and rejection, it was found. that the membranes using DMF and THF showed better performances than the membranes produced by THF only. The water permeability of the final membrane at low pressure(100㎪) showed a typical ultrafiltation membrane's permeability (8-10kg/㎡hr) and good values of rejection(55∼60 percent).

• Korean Chemical Engineering Research
• /
• v.57 no.3
• /
• pp.392-399
• /
• 2019

A highly transparent interfacial layer (HTIL) to enhance the performance of dye-sensitized solar cells (DSSCs) was prepared via a polymer-assisted (PA) approach. Poly(vinyl chloride)-graft-poly(oxyethylene methacrylate) (PVC-g-POEM) was synthesized via atom-transfer radical polymerization (ATRP) and was used as a sacrificial template. The PVC-g-POEM graft copolymer induced partial coordination of a hydrophilic titanium isopropoxide (TTIP) sol-gel solution with the POEM domain, resulting in microphase separation, and in turn, the generation of mesopores upon calcination. These phenomena were confirmed using Fourier-transform infrared (FT-IR) spectroscopy, UV-visible light transmittance spectroscopy, scanning electron microscopy (SEM), and X-ray diffraction (XRD) analysis. The DSSCs incorporating HTIL60/20 (consisting of a top layer with a pore size of 60 nm and a bottom layer with a pore size of 20 nm) exhibited the best overall conversion efficiency (6.36%) among the tested samples, which was 25.9% higher than that of a conventional blocking layer (BL). DSSC was further characterized using the Nyquist plot and incident-photon to electron conversion efficiency (IPCE) spectra.

• Journal of the Korean Ceramic Society
• /
• v.41 no.3
• /
• pp.229-234
• /
• 2004

In this study, we proposed new forming process for a porous ceramic body with unique pore structure. h tubular-type porous NiO-YSZ body with radially aligned pore channels was prepared by freeze-drying of aqueous slurry. A NiO-YSZ slurry was poured into the mold, which was designed to control the crystallization direction of the ice, followed by freezing. Thereafter the ice was sublimated at a reduced pressure. SEM observations revealed that the NiO-YSZ porous body showed aligned large pore channels parallel to the ice growth direction, and fine pores are formed around the outer surface of the tube. It was considered that the difference in the ice growth rate during the freezing process resulted in such a characteristic microstructure. Bilayer consisting of dense thin electrolyte film of YSZ onto the tubular type porous body has been successfully fabricated using a slurry-coating process followed by co-firing. It was regarded that the obtained bilayer structure is suitable for constructing electrode-support type electrochemical devices such as solid oxide fuel cells.

• Carbon letters
• /
• v.1 no.3_4
• /
• pp.117-128
• /
• 2001

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.04a
• /
• pp.209.2-209
• /
• 2003

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.156.2-156
• /
• 2003

• Proceedings of the Korean Ceranic Society Conference
• /
• 2003.10a
• /
• pp.225.1-225
• /
• 2003

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2004.05a
• /
• pp.67-67
• /
• 2004