• Macromolecular Research
• /
• v.10 no.6
• /
• pp.345-358
• /
• 2002

The electrical conductivity during vulcanization process was measured as a function of time for the system of TiC loaded styrene-butadiene rubber (SBR) composites. The phenomenon of negative and positive temperature coefficients of conductivity and its conduction mechanism were also studied for the SBR polymeric composites. The current-voltage characteristics of the polymeric composites were non-linear in high voltage and showed a switching effect. The effects of temperature on the thermal conductivity and effective dielectric constant were measured. The measured parameters were found to be dependent on TiC concentration. The electromagnetic wave shielding (EMS) of the SBR-TiC polymeric composite was also examined. The SBR filled with TiC could be expected to be promising novel smart polymeric composites for self-electrical heating, temperature sensor, time delay switching, and electro-magnetic wave shielding effectiveness.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.9
• /
• pp.2747-2752
• /
• 2013

Surface modification of colloidal silica nanoparticles without disrupting the electric double layer of nanoparticles is a major challenge. In the work, silane was employed to modify colloidal silica nanoparticles without inducing bridge flocculation obviously. The effect of pH value of the silica sol, the amount of silane in feed, and reaction temperature on the graft amount and the final size of modified particles was investigated. The increased weight loss by TG and the appearance of $T_2$ and $T_3$ except for $Q_2$ and $Q_3$ signals by CP/MAS $^{29}Si$ NMR of the modified samples verified the successful grafting of silane. The graft amount reached 0.57 mmol/g, which was slightly lower than theory value, and the particle size remained nearly the same as unmodified particles for acidic silica sol at the optimum condition. For alkaline silica sol after modification, aggregates composed of several nanoparticles connected together with silane moleculars as the bridge appeared.

• Journal of Korean Society on Water Environment
• /
• v.36 no.3
• /
• pp.185-193
• /
• 2020

Bimodal flocculation describes the aggregation and breakage processes of the flocculi (or primary particles) and the flocs in the water environment. Bimodal flocculation causes bimodal size distribution with the two separate peaks of the flocculi and the flocs. Extracellular polymeric substances and ionic species common in the water environment increase the occurrence of bimodal flocculation and flocculi-floc size distribution, under the flocculation mechanisms of electrostatic attraction and polymeric bridging. This study investigated bimodal flocculation and flocculi-floc size distribution, with respect to the extracellular polymeric substance concentration and ionic strength in the kaolinite-containing suspension. The batch flocculation tests comprising 0.12 g/L of kaolinite showed that the highest flocculation potential occurred at the lowest xanthan gum (as extracellular polymeric substances) concentration, under all the ionic strengths of 0.001, 0.01, and 0.1 M NaCl. Also, it was important to note that the higher ionic strength resulted in the higher flocculation potential, at all the xanthan gum concentrations. The bimodal flocculation and flocculi-floc size distribution became apparent in the experimental conditions, which had low and intermediate flocculation potential. Besides the polymeric bridging flocculation, steric stabilization increased the flocculi mass fraction against the floc mass fraction, thereby developing the bimodal size distribution.

• Polymer(Korea)
• /
• v.25 no.5
• /
• pp.625-634
• /
• 2001

New polymeric photostabilizers containing hindered amine light stabilizer (HALS) were prepared by the reaction of liquid polyisoprene rubber grafted maleic anhydride (MAH) and 2,2,5,6-tetramethyl-4-piperidinol (TMPO). Their chemical composition and physical properties were characterized by titration, GPC and TGA analysis. The effects of polymeric HALS on the photooxidation of the styrene-butadiene rubber were studied from the UV, IR spectral changes, and photo-crosslinking was examined by the measurement of the insoluble fraction. The photooxidation of SBR upon irradiation was inhibited by addition of the new polymeric HALS. The extraction resistance of new polymeric photostabilizer was much better than that of the low molecular weight compound which is prepared by the reaction of MAH and TMPO. The new polymeric HALS ate fairly compatible with the SBR.

• Archives of Pharmacal Research
• /
• v.26 no.2
• /
• pp.173-181
• /
• 2003

A polymeric micelle drug delivery system was developed to enhance the solubility of poorly-water soluble drug, biphenyl dimethyl dicarboxylate, DDB. The block copolymers consisting of poly(D,L-lactide) (PLA) as the hydrophobic segment and methoxy poly(ethylene glycol) (mPEG) as the hydrophilic segment were synthesized and characterized by NMR, DSC and MALDI-TOF mass spectroscopy. The size of the polymeric micelles measured by dynamic light scattering showed a narrow monodisperse size distribution with the average diameter less than 50 nm. The MW of mPEG-PLA, 3000 (MW of mPEG, 2 K; MW of PLA, 1K), and the presence of hydrophilic and hydrophobic segments on the polymeric micelles were confirmed by MALDI-TOF mass spectroscopy and NMR, respectively. Polymeric micelle solutions of DDB were prepared by three different methods, i.e. the matrix method, emulsion method and dialysis method. In the matrix method, DDB solubility was reached to 13.29 mg/mL. The mPEG-PLA 2K-1K micelle system was compared with the poloxamer 407 micelle system for their critical micelle concentration, micelle size, solubilizing capacity, stability in dilution and physical state. DDB loaded-polymeric micelles prepared by the matrix method showed a significantly increased aqueous solubility (＞5000 fold over intrinsic solubility) and were found to be superior to the poloxamer 407 micelles as a drug carrier.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.513-514
• /
• 2006

This paper presents the temperature characteristics with the structure of 18 kV surge arresters for distribution system. Three types of polymer arrester were fabricated and a ceramic arrester was also prepared to investigate. Below $100^{\circ}C$, three types of polymeric arresters exhibited almost the same leakage current value, but above $100^{\circ}C$, the polymeric arresters whose module was injected into polymeric housing with the grease exhibited the highest leakage current. In contrary, the arresters being manufactured by directly injecting silicone rubber onto arrester module exhibited the lowest leakage current. The rapid rising of leakage current of the polymeric arresters with the grease at $120^{\circ}C$ was because of the deterioration of the insulation characteristics of the grease between the FRP module and the silicone housing. All polymeric arresters exhibited the same surface temperature characteristics but the ceramic arresters was slower than the polymer arrester in heat emission despite the lowest leakage current. It was thought that the air layer between ZnO varistor blocks and the ceramic housing prevented the heat emission.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.1
• /
• pp.112-116
• /
• 2013

Surface modification of montmorillonite (MMT) with 3-glycidoxypropyl trimethoxysilane (3GTO) in mild methanol/water mixture has been investigated in detail. The influence of reaction conditions (including silane concentration in feed, reaction time and reaction temperature) on the grafting amount and yield of silane, and further on the grafting pattern of silanes was studied by thermogravimetric analysis, elemental analysis, X-ray diffraction (XRD) and BET. Higher silane concentration, longer reaction time and higher reaction temperature are all benefit to higher grafting amount. When the grafting reaction was performed with 3 mmol/g silane concentration, at $90^{\circ}C$ for 24 h, the grafted amount and yield of silane reached 1.4443 mmol/g and 30%, respectively. Based on the XRD and BET data analysis, a speculation that the grafting pattern of silanes was concentration dependence was proposed.

• The Journal of Engineering Research
• /
• v.6 no.2
• /
• pp.5-10
• /
• 2004

• Textile Coloration and Finishing
• /
• v.23 no.3
• /
• pp.163-168
• /
• 2011

In this article, we synthesized an azo dye rotaxane containing bis(8-hydroxyquinoline) group and its polymeric metal complex with zinc. The azo dye rotaxane exhibits high pH sensitivity, solvatochromism and zinc (II) ion sensings in aqueous solution. These behaviors came from the tautomeric equilibrium between azo-hydrazone tautomers and the formation of extended conjugation. The structure of polymeric zinc complexed dye rotaxane was confirmed with NMR and FT-IR measurements. The existence of CD rings, provided by dye rotaxane formation, was found to be very beneficial in improving aqueous solubility of polymeric metal complex.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.5
• /
• pp.179-186
• /
• 1996

The magnetic fibrous polymeric oil filter for automotive was obtained by pneumoextrusion processing prepared from thermoplastic polymer(polyamide) containing magnetic particulate filer (Ba ferrite), and treated subsequently in a magnetic fields. Using an oil filter tester and particle quantifier, the dependence of filtrational characteristics of the magnetic oil filter on the parameters of mean pore sizes and magnetic properties were analyzed. Also experimental engine-bed test of oil filters was investigated. The magnetic fibrous polymeric filter was shown to possess a highly filtration efficiency in filtering the fine metal particles with increasing the magnetic force of filter element. In this study, we knew that efficiency of magnetic fibrous polymeric filter was dependent on the magnetic strength of the filter elements.