• Journal of the Korean institute of surface engineering
• /
• v.49 no.1
• /
• pp.20-25
• /
• 2016

Femtosecond laser ablation of ultrathin polymer films on quartz glass using laser pulses of 100 fs and centered at ${\lambda}=400nm$ wavelength has been investigated for nanometer precision thin film patterning. Single-shot ablation craters on films of various thicknesses have been examined by atomic force microscopy, and beam spot diameters and ablation threshold fluences have been determined by square diameter-regression technique. The ablation thresholds of polymer film are about 1.5 times smaller than that of quartz substrate, which results in patterning crater arrays without damaging the substrate. In particular, at a $1/e^2$ laser spot diameter of $0.86{\mu}m$, the smallest craters of 150-nm diameter are fabricated on 15-nm thick film. The ablation thresholds are not influenced by the film thickness, but diameters of the ablated crater are bigger on thicker films than on thinner films. The ablation efficiency is also influenced by the laser beam spot size, following a $w_{0q}{^{-0.45}}$ dependence.

• Macromolecular Research
• /
• v.16 no.4
• /
• pp.367-372
• /
• 2008

We fabricated tetra(5-n-nonyl-8-tert-butyl-2,3-pyrazino[2,3-b]indolo)porphyrazinato copper(II) (Cu-Pc-$C_8$) Langmuir-Blodgett (LB) films. We further investigated the influence of arachidic acid (AA) as a transfer promoter, as well as the effect of dipping speed, on the deposition of the films on hydrophilic and hydrophobic substrates. In the case of pure Cu-Pc-$C_8$ LB deposition on a hydrophilic substrate, the transfer ratio was close to one for up-stroke depositions, but the previously deposited film was peeled off and re-spread onto water at down-stroke depositions. Whereas the stability of the Cu-Pc-$C_8$ LB films was not improved by AA addition on hydrophilic substrates, the deposition of Cu-Pc-$C_8$ was significantly improved by the presence of AA on a hydrophobic substrate. The AA-assisted deposition had transfer ratio of close to 1 and was essentially stable up to 10-layer depositions. Comparison of the UV-visible spectrum of a Cu-Pc-$C_8$/AA LB film with that of Cu-Pc-$C_8$/AA solution in dichloroethane revealed that the Soret and Q bands for the Cu-Pc-$C_8$/AA LB film were broadened and red-shifted due to the aggregation of phthalocyanines upon assembly in the LB film.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.319-319
• /
• 2010

Dye-sensitized solar cells (DSSCs) based on plastic substrates have attracted much attention mainly due to extensive applications such as ubiquitous powers, as well as the practical reasons such as light weight, flexibility and roll-to-roll process. However, conventional high temperature fabrication technology for glass based DSSCs, cannot be applied to flexible devices because polymer substrates cannot withstand the heat more than $150^{\circ}C$. Therefore, low temperature fabrication process, without using a polymer binder or thermal sintering, was required to fabricate necked $TiO_2$. In this presentation, we proposed polymer-inorganic composite photoelectrode, which can be fabricated at low temperature. The concept of composite electrode takes an advantage of utilizing elastic properties of polymers, such as good impact strength. As an elastic material, poly(methyl methacrylate) (PMMA) is selected because of its optical transparency and good adhesive properties. In this work, a polymer-inorganic composite electrode was constructed on FTO/glass substrate under low temperature sintering condition, from the mixture of PMMA and $TiO_2$ colloidal solution. The effect of PMMA composition on the photovoltaic property was investigated. Then, the enhanced mechanical stability of this composite electrode on ITO/PEN substrate was also demonstrated from bending test.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.523-525
• /
• 2008

Inkjet printing is being considered as an alternative to the conventional lithography in the electronic industry. Surface energy control of substrate is a critical issue in controlling the dimension of microstructures by the inkjet printing. This study introduces the surface energy control of ITO substrate for in/q'et printing of PEDOT/PSS.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.201-201
• /
• 2006

In this study the glass transition temperature in thin polymer films has been studied. Ellipsometry has been used to measure $T_{g}$ of thin film as a function of film thickness. Empirical equation has been proposed to fit the measured $T_{g}$ pattern with thickness. Also, a continuous multilayer model was proposed and derived to describe the effect of surface on the observed $T_{g}$ reduction in thin films, and the depth-dependent $T_{g}$ profile was obtained. These results showed that $T_{g}$ at the top surface was much lower than the bulk $T_{g}$ and gradually approached the bulk $T_{g}$ with increasing distance from the edge of the film. The model and equation were modified to apply for the polymer coated on the strongly favorable substrate and the freely standing film.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.17 no.3
• /
• pp.20-26
• /
• 2008

Nanoimprint lithography(NIL) is becoming next generation lithography of significant interest due to its low cost and a potential patterning resolution of 10nm or less. Success of the NIL relies on the adequate conditions of pressure, temperature and time. To have the adequate conditions for NIL, one has to understand the polymer flowing behavior during the imprinting process. In this paper, an analytical approach of polymer flow in thermal NIL was performed based on the squeeze flow with partial slip boundary conditions. Velocity profiles and pressure distributions of the polymer flow were obtained and imprinting forces and residual thickness were predicted with the consideration of the slip velocity between the polymer and the mold/substrate. The results show that the consideration of the slip is very important for investigating the polymer flow in Thermal NIL.

• Journal of the Korean Chemical Society
• /
• v.20 no.4
• /
• pp.251-259
• /
• 1976

Graft site distribution of graft polymer was derived from a statistical model. Theoretical model was experimentally confirmed by preparing well defined graft polymer and using gel permeation chromatography(GPC). The results indicate that metalation of substrate polymer is statistically random process and anionic graft reaction products consist of ungrafted free side chain homopolymer; graft polymer with different number of graft chains and free backbone molecules when the averaged in the graft sites are small.

• Macromolecular Research
• /
• v.14 no.2
• /
• pp.245-250
• /
• 2006

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.273-276
• /
• 2003

Polymerization induced diffusion has been successfully applied to create new display components. Based on this principle a new technique to produce polymer covered liquid crystal layers on a single substrate, called photo-enforced stratification, allows cost-effective production of ultra-thin LCDs. The two-step photopolymerization-induced phase separation of a liquid crystal and a polymer precursor can be performed on a variety of substrates and provides freedom in display design.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.611-614
• /
• 2003

We have investigated electric field effect on the formation of phase separated composite organic film structure which is utilized by anisotropic phase separation from LC and prepolymer mixtures. Application of bias field resulted in a significant change in liquid crystal alignment between glass substrate and polymer layer. The liquid crystal molecules segregated into the inter-electrodes and formed twisted structure which is the result of imprinting of LC alignment by the bias field on polymer layers during polymerization process.