• Polymer(Korea)
• /
• v.24 no.5
• /
• pp.579-588
• /
• 2000

The effects of protective colloids on the colloid stability of poly(vinyl acetate) (PVAc) latex was investigated. The stability of PVAc latex in reactive poly(vinyl alcohol) mono thiol (PVALT) (DP=1080) having 78.4% saponification value was better than poly (vinyl alcohol)(PVA) (DP=1100) having 81.6% saponification value. The colloidal stability of PVAc latex particles improved drastically with increase of the reactive PVALT. The particle surface morphology of PVAc latex was examined by transmission electron microscopy (TEM). It was shown that particle size of 1ha latexes decreased with increasing reactive PVALT concentration. Therefore, the stabilities of latex for reactive PVALT protective colloid was superior to that of PVA ones. This result is due to the introduction of many thiol groups that induce chemical bonds at PVAc latexes surface, so that the formation of PVALT-b-PVAc block copolymer via the reaction of PVAc with reactive PVALT. In addition, zeta potential of the PVAc latexes decreased with increasing sodium carbonate concentration.

• Journal of the Korean Magnetics Society
• /
• v.16 no.1
• /
• pp.107-110
• /
• 2006

Magnetite nanoparticles encapsulated with biodegradable polymer [poly(D,L-lactide-co-glycoiide), PLGA] were prepared by an emulsification-diffusion method. To investigate the effect of type of organic solvents on the mean particle sizes of obtained composite particles, different organic solvents [ethyl acetate (EA), propylene carbonate (PC) and acetone (ACE)] were used with a stabilizer [didodecyl dimethyl ammonium bromide (DMAB)]. The particle size of nanoparticles was observed by the dynamic light scattering method. When EA and PC as partially water-soluble solvents were used, small composite nanoparticles below 80nm were obtained, while large composite nanoparticles above 330nm were prepared for ACE as a fully water-soluble solvent.

• Elastomers and Composites
• /
• v.45 no.2
• /
• pp.122-128
• /
• 2010

We measured shear viscosity of copoly(styrene(St)/butyl methacrylate(BMA)) (co-PSB) particles, with a capillary rheometer at $170^{\circ}C$, prepared by suspension polymerization with hydrophobic silica as a stabilizer. co-PSB particles with the weight average molecular weights of lower than 74,800 g/mol displayed a Newtonian behavior at low shear rates. With the weight average molecular weight exceeding 136,800 g/mol, co-PSB particles showed shear thinning against shear rates and the absolute value of the slopes between shear viscosity vs. shear rate increased. When the ratio between St and BMA changed from 7/3 to 5/5 to 3/7, shear viscosity and glass transition decreased despite similar molecular weights. When the ratio was 1/9, it showed a large increase in initial shear viscosity despite reduced glass transition. Shear viscosity exhibited an increase in proportion to carbon black concentration. The effect of carbon black concentration on the shear viscosity of co-PSB composites was less pronounced compared to varying molecular weights and/or compositional ratio.

• Polymer(Korea)
• /
• v.38 no.3
• /
• pp.314-319
• /
• 2014

Three kinds of thermal stabilizers for nylon 4 were synthesized to incorporate both hindered amine groups and methylene units with various lengths. It is expected that the hindered amine groups play a role in the capture of degradation-triggering species. Considering sequence rules, hydrogen bonding formed between nylon 4 and the stabilizers is optimized to alter the lengths of the methylene units in the stabilizers. As a result, it was found that a tetramethylene unit in the stabilizer is an optimal length for hydrogen bonding in terms of isothermal thermogravimetric analysis (TGA). Considering the slight and often negligible improvement of thermal stability of nylon 4 containing commercially-available nylon 6 stabilizers, retardation of thermal degradation has been substantially improved upon.

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.5
• /
• pp.450-457
• /
• 2018

To design the practical core-shell electrocatalysts, combination of core and shell materials is important to meet catalytic activity and durability target. In general, Pd is considered as a good core material due to its best activity caused by strain/ligand effect. Preparing Pd nanoparticles can be a starting point in fabricating core-shell type electrocatalysts, much simplified Pd preparing process is suggested by using carbon monoxide (CO) as a reducing agent and/or capping agent. The solvent composition and reaction temperature can control to nanosheet, tetrahedron, and sphere without using additional stabilizer. Among them, Pd nanosheet which has mainly (111) plane showed about 3 times higher electrocatalytic activity for oxygen reduction reaction (ORR) to the spherical Pd nanoparticles. The enhanced ORR activity of Pd nanosheets can be attributed to the exposure of Pd (111) surface and the high electrochemical surface area. Therefore, we demonstrated that the shape of Pd nanomaterials is easily controlled via a facile reduction method using CO, and (111) plane-oriented Pd nanosheets can be a promising ORR catalysts and core material for polymer electrolyte fuel cells (PEFCs).

• Elastomers and Composites
• /
• v.34 no.3
• /
• pp.199-211
• /
• 1999

In this work, the effects of the addition of epoxy on the properties of PVC-sol sealants were investigated. PVC-sol was plasticized with dioctyl phthalates(DOP). Two kinds of epoxy resins having different epoxy equivalent weight (E.E.W.) were used. It was found that the properties of the PVC-sol sealants were significantly affected by the contents and types of the added epoxy resins. The viscosity behaviors of the epoxy-modified sealants, in the case of epoxy A addition, the viscosity was decreased with increasing the epoxy contents, but In the case of $CaCO_3$ addition, the viscosity was increased with increasing the $CaCO_3$ contents. The viscosity of epoxy modified sealants aged at $45^{\circ}C$ waterbath was decreased with increasing epoxy contents, since the epoxy acted on the sealants as a stabilizer. The thermal stability of the PVC-sol sealants was slightly improved by adding epoxy. The tensile strength and elongation of sealants modified with epoxy A(two functionalities of epoxy) were increased with increasing the epoxy contents up to a certain epoxy contents but was decreased with further increasing the epoxy contents. In the case of $CaCO_3$ addition, the tensile strength of sealants were decreased with increasing the $CaCO_3$ contents. In view of the electrical properties, such as tan ${\delta}$($0.1{\pm}0.04$) and ${\epsilon}_r$($0.5{\pm}0.04$), it was found that the epoxy modified sealants were as good as insulators.

• Elastomers and Composites
• /
• v.37 no.1
• /
• pp.7-13
• /
• 2002

In this study, mechanical properties of PVC complexes containing the gypsum (Namhae Chemical Co.) which contains phosphte, CaO, etc., Pb-species stabilizer, and $CaCO_3$ were investigated as a function or the content. As a result, mechanical properties increased when the gypsum was mixed with PVC at the extent of 8.46wt%. From this result, it is suggested that the gypsum containing phosphate and CaO is compatible with PVC. Thermogravimetric analysis(TGA) showed that pyrolysis started about at $275^{\circ}C$, and residual weight(%) increased with the amount of the gypsum, and differential scanning calorimetry (DSC) showed that $T_m,\;T_g$ had the maximum and minimum value respectively when the gypsum was mixed with PVC at the extent of 8.46wt%. Comparing all the results, both mechanical and thermal properties of PVC complex were improved. The X-ray diffraction measurement also showed their blonds and structures.

• Macromolecular Research
• /
• v.17 no.10
• /
• pp.750-756
• /
• 2009

Stable, spherical, polystyrene particles were synthesized in ab initio dispersion polymerization by using the poly(methacrylic acid)[PMAA] macro-RAFT agent. The presence of the PMAA macro-RAFT agent on the polystyrene (PS) particles was confirmed by NMR and FTIR spectroscopy. The PS particle size was influenced by the concentration of the RAFT agent and monomer due to the initial nucleation. When the concentration of the PMAA macro-RAFT agent was increased from 2 to 10 wt% relative to the monomer, the average particle size decreased from 2.31 to 1.36 ${\mu}m$, the conversion decreased from 93.3 to 88.9%, the weight-average molecular weight increased from 46,300 to 150,200 g $mol^{-1}$ and the PDI decreased from 2.79 to 1.94, respectively. In particular, the incorporation of 10 wt% of PMAA macro-RAFT agent produced monodisperse PS spheres of 1.36 ${\mu}m$ with a coefficient of variation (CV) of 6.44%. Thus, the PMAA macro-RAFT agent worked as a reactive steric stabilizer providing monodisperse, micron-sized, PS particles.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.5
• /
• pp.1345-1348
• /
• 2010

Highly monodisperse polystyrene (PS) nanospheres were fabricated by surfactant-free emulsion polymerization in water using styrene, 2,2'-azobis(2-methyl propionamidine) dihydrochloride (AIBA), and poly(vinyl pyrrolidone) (PVP). The size and distribution of the PS nanospheres were systematically investigated in terms of initiator concentration, stabilizer concentration, reaction temperature, reaction time, and reactant concentration. With increasing AIBA initiator concentration, PS particle sizes are raised proportionally, and can be controlled from 120 to 380 nm. Particle sizes were reduced with increasing PVP concentration. This decrease occurs because a high PVP concentration leads to a large number of primary nuclei in the early stage of polymerization. When the reaction temperature increased, the sizes of the PS particles decrease slightly. The particles grew quickly during the initial reaction stage (1-3 h) and the growth rate became steady-state after 6 h. The PS sizes approximately doubled when the reactant (styrene, PVP, azo-initiator) concentrations were increased by a factor of eight.

• Analytical Science and Technology
• /
• v.13 no.3
• /
• pp.282-290
• /
• 2000

In this study, polymer additives were extracted and separated by Soxhlet extraction method and the dissolution-precipitation method from a polycarbonate (optical grade) which completely absorbed UV light below 390 nm. Analytical techniques such as UV-Vis spectroscopy, FT-IR, and HPLC were applied to analyze additives in polycarbonate. Separated materials from the polycarbonate may be a complex mixture containing additives such as UV stabilizer, antioxidants (primary and secondary), monomers, and oligomers. Several compounds such as bisphenol A, Irganox 1010, and Cyasorb UV-5411 were identified by chromatograms and UV spectra obtained from RP HPLC analysis using Bondapak $C_{18}$ column, methanol mobile phase, and a photodiode array (PDA) detector. Also, the content of UV-5411 in the polycarbonate was about 0.12 wt% by a quantitative analysis through UV spectroscopy.