• Journal of the Korean Electrochemical Society
• /
• v.12 no.2
• /
• pp.173-180
• /
• 2009

In order to develop a novel polymer electrolyte membrane for direct methanol fuel cell (DMFC), styrene monomer was graft-polymerized into poly(tetrafluoroethylene perfluoropropyl vinyl ether) (PFA) film followed by a sulfonation reaction. The graft polymerization was prepared by the $\Upsilon$-ray radiation-grafting method. Subsequently, sulfonation of the radiation-grafted film was carried out in a chlorosulfonic acid/1,2-dichloroethane (2 v/v%) solution. The chemical, physical, electrochemical and morphological properties of the radiation-grafted membranes (PFA-g-PSSA) were characterized by fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The water uptake, ionic conductivity, and methanol permeability of the PFA-g-PSSA membrane were also measured. The cell performances of MEA prepared with the PFA-g-PSSA membranes were evaluated and the cell resistances were measured by an impedance analyzer. The MEA using PFA-g-PSSA membranes showed superior performance for DMFCs in comparison with the commercial Nafion 112 membrane.

• Polymer(Korea)
• /
• v.34 no.1
• /
• pp.20-24
• /
• 2010

In this study, ETFE-g-PSSA membranes with various degrees of grafting (DOG) and thicknesses were prepared by a simultaneous irradiation method. SEM-EDX instrument was applied to measure the relative distribution of sulfur which is corresponding to that of a grafted polymer over the Cross-section of the ETFE-g-PSSA membranes prepared at various irradiation conditions. The results indicate that to obtain the evenly-grafted membranes, a styrene/dichloromethane ratio is needed to be under 60 (v/v%), and a higher DOG is required as the film thickness increases. The effects of DOG and thickness on the ion exchanging capacity (IEC) and water uptake (WU) were investigated by measuring the IEC and WU values of the membranes with various DOG and thicknesses.

• Polymer(Korea)
• /
• v.31 no.1
• /
• pp.80-85
• /
• 2007

Maleic anhydride (MA) modified ethylene-propylene-diene terpolymer (MEPDM) was pre-pared from solution polymerization. MEPDM-g-PST copolymer was prepared by melt polymerization of male ate d EPDM and quaternary ammonium silyl polydimethylsiloxane -7,7,8,8- tetracyanoquinodimethane (TCNQ) adduct (PST) in internal mixer and MEPDM-g-PST/HDPE/CB (MPEC) was prepared by com-pounding HDPE, MEPDM-g-PST copolymer and carbon black (CB, 5, 10, 15, and 20 phr), and HDPE/ CB (PEC) by compounding HDPE and CB (5, 10, 15, and 20 phr), respectively. The structure of MEPDM-g-PST copolymer was confirmed by measuring the FTIR. The maximum grafting ratio of MA onto EPDM was 2.35%. The thermal and mechanical properties of the composites were measured and dispersion characteristics of CB in matrix show that CB in MPEC was better dispersed than that in PEC composite.

• Macromolecular Research
• /
• v.13 no.1
• /
• pp.45-53
• /
• 2005

In this study, a series of highly swelling hydrogels based on sodium alginate (NaAlg) and polymethacryl­amide (PMAM) was prepared through free radical polymerization. The graft copolymerization reaction was performed in a homogeneous medium and in the presence of ammonium persulfate (APS) as an initiator and N,N'-methylenebis­acrylamide (MBA) as a crosslinker. The crosslinked graft copolymer, alginate-graft-polymethacrylamide (Alg-g­PMAM), was then partially hydrolyzed by NaOH solution to yield a hydrogel, hydrolyzed alginate-graft-poly­methacrylamide (H-Alg-g-PMAM). During alkaline hydrolysis, the carboxamide groups of Alg-g-PMAM were converted into hydrophilic carboxylate anions. Either the Alg-g-PMAM or the H-Alg-g-PMAM was characterized by FTIR spectroscopy. The effects of the grafting variables (i.e., concentration of MBA, MAM, and APS) and the alkaline hydrolysis conditions (i.e., NaOH concentration, hydrolysis time, and temperature) were optimized systematically to achieve a hydrogel having the maximum swelling capacity. Measurements of the absorbency in various aqueous salt solutions indicated that the swelling capacity decreased upon increasing the ionic strength of the swelling medium. This behavior could be attributed to a charge screening effect for monovalent cations, as well as ionic cross-linking for multivalent cations. Because of the high swelling capacity in salt solutions, however, the hydrogels might be considered as anti-salt superabsorbents. The swelling behavior of the superabsorbing hydrogels was also measured in solutions having values of pH ranging from 1 to 13. Furthermore, the pH reversibility and on/off switching behavior, measured at pH 2.0 and 8.0, suggested that the synthesized hydrogels were excellent candidates for the controlled delivery of bioactive agents. Finally, we performed preliminary investigations of the swelling kinetics of the synthesized hydrogels at various particle sizes.

• Applied Chemistry for Engineering
• /
• v.32 no.4
• /
• pp.371-378
• /
• 2021

The formation of hydrophilic surface based on polymers has received great attention due to the anti-adhesion of bacteria on solid substrates. Anti-adhesion coatings are aimed at suppressing the initial step of biofilm formation via non-cytotoxic mechanisms, and surfaces applied hydrophilic or ionic polymers showed the anti-adhesion effect for bioentities, such as proteins and bacteria. This is attributed to the formation of surface barrier from hydration layers, repulsions and osmotic stresses from polymer brushes, and electrostatic interactions between ionic polymers and cell surfaces. The antifouling polymer coating is usually fabricated by the grafting method through the bonding with functional groups on surfaces and the deposition method utilizing biomimetic anchors. This mini-review is a summary of representative antifouling polymers, coating strategies, and antibacterial efficacy. Furthermore, we will discuss consideration on the large area surface coating for application to public facilities and industry.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.spc8
• /
• pp.2988-2996
• /
• 2011

Shape memory polyurethane (SMPU), grafted with a fluorescent dye (Rhodamine, Mehylene violet, or Fluorescein) through an allophanate linking, was tested for the fluorescence and the shape recovery effect. The main chain of SMPU was composed of 4,4'-methylenebis(phenylisocyanate) (MDI), poly(tetramethyleneglycol) (PTMG), and 1,4-butanediol (BD), and a fluorescent dye was connected through a second MDI linked to the carbamate moiety of the main chain. Three series of SMPU, differing according to their dye content, were prepared to compare their shape recovery and fluorescence properties. In tensile mechanical property, maximum stress increased up to 350% compared to the linear SMPU, and strain remained above 2000%. Shape recovery went to as high as 97%, and remained almost same after repetitive shape recovery test cycles. Finally, the fluorescence emission of SMPU was demonstrated in the luminescence spectrum and fluorescent light emission pictures. In addition, the response of SMPU to external stimuli such as metal ions was investigated.

• Polymer(Korea)
• /
• v.25 no.5
• /
• pp.625-634
• /
• 2001

New polymeric photostabilizers containing hindered amine light stabilizer (HALS) were prepared by the reaction of liquid polyisoprene rubber grafted maleic anhydride (MAH) and 2,2,5,6-tetramethyl-4-piperidinol (TMPO). Their chemical composition and physical properties were characterized by titration, GPC and TGA analysis. The effects of polymeric HALS on the photooxidation of the styrene-butadiene rubber were studied from the UV, IR spectral changes, and photo-crosslinking was examined by the measurement of the insoluble fraction. The photooxidation of SBR upon irradiation was inhibited by addition of the new polymeric HALS. The extraction resistance of new polymeric photostabilizer was much better than that of the low molecular weight compound which is prepared by the reaction of MAH and TMPO. The new polymeric HALS ate fairly compatible with the SBR.

• Polymer(Korea)
• /
• v.24 no.2
• /
• pp.174-181
• /
• 2000

The ACF/PP-g-AN copolymers were synthesized by the irradiational grafting of acrylonitrile onto ACF/PP hybrid fabric. The synthesis of the ACF/PP-g-AN copolymer was evidenced by the band of -C=N absorption peak at 2250 $cm^{-1}$ / and amidoximation was evidenced by the band of -OH and -NH$_2$ peak at 3450 $cm^{-1}$ / on FT-IR spectrum. The optimal time for the uranium ion adsorption equilibrium on ACF/PP-g-AN copolymers was 8 days and the optimal pH was 8. The adsorption capacities of ACF/PP-g-AN copolymers increased according to the content of amidoxime and were not varied even after more than 10 times of regeneration.

• Membrane and Water Treatment
• /
• v.1 no.2
• /
• pp.103-120
• /
• 2010

Surface modification of microfiltration and ultrafiltration membranes has been widely used to improve the protein adsorption resistance and permeation properties of hydrophobic membranes. Several surface modification methods for converting conventional membranes into low-protein-binding membranes are reviewed. They are categorized as either physical modification or chemical modification of the membrane surface. Physical modification of the membrane surface can be achieved by coating it with hydrophilic polymers, hydrophilic-hydrophobic copolymers, surfactants or proteins. Another method of physical modification is plasma treatment with gases. A hydrophilic membrane surface can be also generated during phase-inverted micro-separation during membrane formation, by blending hydrophilic or hydrophilic-hydrophobic polymers with a hydrophobic base membrane polymer. The most widely used method of chemical modification is surface grafting of a hydrophilic polymer by UV polymerization because it is the easiest method; the membranes are dipped into monomers with and without photo-initiators, then irradiated with UV. Plasma-induced polymerization of hydrophilic monomers on the surface is another popular method, and surface chemical reactions have also been developed by several researchers. Several important examples of physical and chemical modifications of membrane surfaces for low-protein-binding are summarized in this article.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.1
• /
• pp.35-41
• /
• 2019

Ferrocene and ferrocene derivatives have been widely used as a burning rate catalyst for composite solid propellants. However, its tendency to migrate through the propellant grain and to crystallize at the surface changes the composition of propellant which results in unpredictable burning rate. To overcome the weakness of ferrocene catalyst, we designed a polymer containing ferrocene, poly(glycidyl azide-co-glycidyl ferrocenyl ether) (GAFP). GAFPs were synthesized from poly(epichlorohydrin-co-glycidyl ferrocenyl ether) (PEGF) which has ferrocenyl ethers in its pendant groups. The structures of GAFPs were confirmed by FT-IR, $^1H$ and $^{13}C$ NMR spectral analyses. Thermal properties of the GAFPs were evaluated using differential scanning calorimeter (DSC). As the contents of ferrocene increased, the glass transition temperature ($T_g$) of the GAFPs shifted to a higher temperature, and the decomposition temperature ($T_d$) decreased because the ferrocene worked as a burning rate catalyst.