• 한국세라믹학회지
• /
• 제29권4호
• /
• pp.298-304
• /
• 1992

Flexural strength, microstructure, hydration reaction and moisture sensitivity in macro defect-free (MDF) cement, which basically prepared of high alumina cement (HAC) and hydroxypropyl methylcellulose (HPMC) and polyvinylalcohol (PVA) as water soluble polymer were investigated. Cement composites based on HAC-PVA system were improved in flexural strength than that of HAC-HPMC system especially, the strength of specimens added to 10 wt% of polyvinylalcohol was 160 MPa. These improvements of flexural strength were attributed to not only the effect of water soluble polymer in elimination of macropores (above 100 $\mu\textrm{m}$) and cement grain bridging, but the effect of unhydrate cement as an aggregate. Moisture sensitivity and flexural strength in wet condition of MDF cement composites immersed in water at 80$^{\circ}C$ for 3 days were decreased.

• 한국건축시공학회지
• /
• 제8권6호
• /
• pp.131-137
• /
• 2008

In recent years, the light-weight aggregate has widely been used to reduce the weight of construction structures, and to achieve the thermal insulation of building structures. The purpose of this study is to evaluate the heat resistance of polymer concrete composites with light-weight aggregate made by binders as resin and cement with polymer dispersion. The light-weight polymer concrete composites are prepared with various conditions such as binder content, filler content, void-filling ratio, light-weight aggregate content and polymer-cement ratio, and tested for heat resistant test, and measured the weight reducing ratio, strengths and exhaustion content of gas such as CO, NO and $SO_2$. From the test results, the weight reducing ratio of light weight polymer concrete using UP binder after heat resistance test increase with an increase in the UP content irrespective of the filler content. The weight reducing ratio of polymer cement concrete is considerably smaller than that of UP concrete. In general, the strengths after heat resistance of polymer concrete composites are reduced about 40 to 65% compared with those before test. The exhausted quantity of CO, NO and $SO_2$ gases in polymer concrete composites is less than EPS(Expanded poly styrene). From the this study, it is confirmed that the many types gases discharge according to binder type of polymer concrete composites, its amount is controlled by selection of the binder type and mix proportions.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 가을학술발표대회논문집
• /
• pp.181-182
• /
• 2023

This study is a study on the flexural adhesion performance of polymer cement composites(PCCs) repair section according to the crack depth, and the flexural adhesion strength was obtained through a flexural strength test of cement mortar that was filled into cracks and repaired to a certain thickness using PCCs made of ultra high-early strength cement and polymer dispersion of EVA. As a result of the study, the flexural adhesion performance according to the crack width and crack depth was expected to decrease the flexural adhesion strength as the crack depth increased at the crack width 3.0mm, but the crack width 2.0mm and 1.5mm did not show any tendency according to the crack depth. In addition, even in the final destruction, the fact that the cracks and bottoms filled with PCCs were not cut or dropped proves that PCCs have excellent adhesion and rich toughness.

• 한국세라믹학회지
• /
• 제30권2호
• /
• pp.139-147
• /
• 1993

Two sheets of high strength cement paste using ordinary Portland cement and water soluble polymer (polyacrylamide) were made by kneading with a twin roll mill. A carbon fiber layer out between two sheet of the cement paste, and then carbon fiber reinforced high strength cement composites were prepared by pressing them. The mechanical properties of the composites were investigated through the observation of the microstructure and the application of fracture mechanics. When the carbon fiber was added with 0.2 and 0.3wt% to the composites the flexural strength and Young's modulus were about 110∼116MPa and 74∼77GPa respectively, and critical stress intensity was about 3.14MPam1/2. It can be considered that the strength improvement of high strength cement fiber composites may be due to the removal of macropores and the increase of various fracture toughness effects; grain bridging, frictional interlocking, polymer fibril bridging and fiber bridging.

• 한국구조물진단유지관리공학회 논문집
• /
• 제27권5호
• /
• pp.97-104
• /
• 2023

본 연구는 RC 구조물의 균열보수를 위한 보수재로서 폴리머 디스퍼전과 시멘트만으로 구성된 폴리머 시멘트 복합체 (polymer cement Composites ; PCCs)를 제작하여 실험적으로 기초물성을 파악하고자 하였다. 연구를 위한 시험배합은 EVA 및 SAE 폴리머 디스퍼전을 기반으로 보수재의 충전성을 고려하여 폴리머 시멘트비를 4가지(20, 60, 80 및 100%)로 변환시키면서 물시멘트비를 정해 PCCs의 점도를 결정하였다. 또한 PCCs의 강성을 개선시키기 위하여 P/C 80%와 100%에 실리카퓸을 혼입한 시험편도 제작하였다. PCCs의 균열보수용으로서의 점도, 유동성, 충전성, 인장강도, 신장률 및 탄성계수 등 기초적 물성을 실험하였다. 연구결과, 폴리머의 종류에 따라 P/C는 점도와 유동성에 큰 영향을 미쳤으며 RC 구조물의 균열보수용으로서 충전성을 고려한 적절한 점도를 맞춘 배합설계를 위해 상당한 가수가 필요하였다. 본 연구에서 설계한 모든 배합은 충전성이 우수하였으며, PCCs의 인장강도와 신장률은 시멘트 혼입 폴리머계 방수재에 대한 KS 규정을 만족하였다. 또한 실리카퓸을 혼입함으로써 PCCs의 인장강도와 탄성계수가 개선되었으며, 폴리머 종류에 따라서는 SAE를 사용한 경우가 EVA를 사용한 경우에 비해 RC 구조물 균열 보수재로서 우수한 기초적인 물성을 나타냈다. 본 연구결과를 종합하면, RC 구조물의 균열보수용으로 SAE를 사용한 P/C 80% 또는 100%와 실리카퓸 30%까지 혼입한 배합을 적절한 배합으로 제안할 수 있었다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 가을학술발표대회논문집
• /
• pp.179-180
• /
• 2023

The adhesion performance of PCCs for crack repair of RC structures was greater in the case of using ultra high-early strength cement than in the case of using ordinary Portland cement, and the effect of mixing silica fume was higher in the case of ordinary Portland cement than that of ultra high-early strength cement. On the other hand, 130% of W/C was more fluid than 80% of W/C in the same P/C 80%, which increased the fillability and improved the strength, but the strength improvement effect was the greatest in adhesion in flexure. Through this study, the basic characteristics of the adhesion performance of PCCs were identified, and based on this, it is necessary to induce an optimal mixing design that can increase adhesion performance through various mixing designs.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권1호
• /
• pp.102-112
• /
• 2019

본 연구는 PVA(polyvinyl alcohol) 섬유와 VAE(vinyl acetate ethylene) 분말 폴리머를 사용한 시멘트복합체의 압축 휨강도 와 온도변화에 따른 충격파괴거동을 연구하였다. 충격시험은 $-35^{\circ}C$, $0^{\circ}C$ 및 $35^{\circ}C$의 선정된 온도조건에서 실시하였다. 본 실험에서는 시멘트 복합체와 일반 모르타르에 대한 충격파괴 에너지와 변위, 시간을 얻기 위해 낙하 충격시험기(Ceast 9350)를 사용하여 충격시험을 수행하였다. 강도시험결과, PVA 섬유와 VAE 분말 폴리머의 휨강도는 모두 증가하였다. PVA 섬유보강 시멘트복합체의 경우 재령 28일에서의 압축강도는 약간 감소하였으나, 휨강도는 일반 모르타르 강도보다 24.4% 증가하였다. 낙하 충격시험 결과, PVA 섬유보강 시멘트복합체 시편은 섬유의 가교역할로 인한 균열발생의 억제와 에너지 분산에 의한 미세균열이 발생하였으며, 충격에 의한 배면파괴와 관통에 대하여 억제되었다. 반면 VAE 분말 폴리머 시멘트복합체와 일반 모르타르의 시편은 대부분 큰 균열이나 관통파괴 되었다. 충격하중을 받는 시멘트복합체와 일반 모르타르의 시편은 대부분 국부적인 취성파괴거동을 보이며, PVA 섬유보강에 의한 휨성능 증진으로 인해 충격에 대한 저항성능이 크게 향상되었다.

• Carbon letters
• /
• 제24권
• /
• pp.90-96
• /
• 2017

We demonstrated the sensitivity of optically active single-walled carbon nanotubes (SWCNTs) with a diameter below 1 nm that were homogeneously dispersed in cement composites under a mechanical load. Deoxyribonucleic acid (DNA) was selected as the dispersing agent to achieve a homogeneous dispersion of SWCNTs in an aqueous solution, and the dispersion state of the SWCNTs were characterized using various optical tools. It was found that the addition of a large amount of DNA prohibited the structural evolution of calcium hydroxide and calcium silicate hydrate. Based on the in-situ Raman and X-ray diffraction studies, it was evident that hydrophilic functional groups within the DNA strongly retarded the hydration reaction. The optimum amount of DNA with respect to the cement was found to be 0.05 wt%. The strong Raman signals coming from the SWCNTs entrapped in the cement composites enabled us to understand their dispersion state within the cement as well as their interfacial interaction. The G and G' bands of the SWCNTs sensitively varied under mechanical compression. Our results indicate that an extremely small amount of SWCNTs can be used as an optical strain sensor if they are homogeneously dispersed within cement composites.

• 한국건축시공학회지
• /
• 제24권1호
• /
• pp.23-34
• /
• 2024

본 연구의 목적은 RC 구조물의 균열 보수용 폴리머 시멘트 복합체의 휨접착성능을 평가하기 위함이다. 시멘트 모르타르에 다양한 크기의 균열을 만들어 PCCs를 충전한 후, 소정의 양생을 거쳐 휨접착강도와 휨강도 개선 정도를 파악하였다. 연구결과, 균열보수용 PCCs의 휨접착강도는 시멘트의 종류, 폴리머 종류 및 폴리머 결합재비에 따라 영향을 받으며 실리카퓸을 혼입한 초조강시멘트를 사용한 경우가 보통시멘트를 사용한 경우에 비해 최대 19.0%의 휨접착강도 개선효과가 나타났다. PCCs로 충전된 시멘트 모르타르의 휨강도 개선 정도는 균열폭의 영향보다는 균열깊이에 따라 큰 차이를 보였으며 균열에 충전된 PCCs가 단순히 보수재료로서 기능뿐만 아니라 어느 정도 휨강도를 개선시키는 보강재료로서도 역할을 하였다. 본 연구결과, 초조강시멘트, 3종류의 폴리머 디스퍼전과 실리카퓸, 60%~80%의 높은 폴리머 결합재비로 제작한 PCCs가 균열을 충전하는 보수재료로서 현장에서 충분히 사용될 수 있을 것이다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1993년도 봄 학술발표회 논문집
• /
• pp.93-98
• /
• 1993

In order to discuss the mechanical properties of fiber reinforced composites with fly ash, lime, gypsum and polymer emulsion-Stylene Butadiene Rubber Latex (SBR) , experimental studies on FRC were carried out. The kinds of fiber used in FRC are PAN-dervied and Pitch-derived carbon fiver, alkali-resistance glass fiber. As a test results, the flexural strength and tougthness of fiber reinforced fly ash. lime.gypsum cement composites are remarkably increased by fiber contents ,but compressive strength of the composites are influenced by kinds of fiber more than by fiber contents. Also, addition of a polymer emulsion (SBR) to the composites decreased the bulk specific gravity, but compressive and flexural strengths, toughness of the composites are not influenced by it, are considerably improved by increasing fiber contents.