• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.1
• /
• pp.35-41
• /
• 2019

Ferrocene and ferrocene derivatives have been widely used as a burning rate catalyst for composite solid propellants. However, its tendency to migrate through the propellant grain and to crystallize at the surface changes the composition of propellant which results in unpredictable burning rate. To overcome the weakness of ferrocene catalyst, we designed a polymer containing ferrocene, poly(glycidyl azide-co-glycidyl ferrocenyl ether) (GAFP). GAFPs were synthesized from poly(epichlorohydrin-co-glycidyl ferrocenyl ether) (PEGF) which has ferrocenyl ethers in its pendant groups. The structures of GAFPs were confirmed by FT-IR, $^1H$ and $^{13}C$ NMR spectral analyses. Thermal properties of the GAFPs were evaluated using differential scanning calorimeter (DSC). As the contents of ferrocene increased, the glass transition temperature ($T_g$) of the GAFPs shifted to a higher temperature, and the decomposition temperature ($T_d$) decreased because the ferrocene worked as a burning rate catalyst.

• International Journal of Highway Engineering
• /
• v.4 no.1 s.11
• /
• pp.149-159
• /
• 2002

This study was performed to estimate the high-speed direct tensile strength(DTS1), low-speed direct tensile strength(DTS2) , indirect tensile strength(ITS) resilient modulus(MR) and stiffness index(SI) of sand asphalt mixture based on the absolute viscosity, kinematic viscosity, penetration, softening point and PG grade of binder. DTS2 showed higher correlation with the physical properties than other properties of mixture, and the next was DTS1, ITS, SI and MR in order. Among binder properties, PG grade showed the highest relation with DTS2. Therefore. it was found that the high DTS mixture could be made when the binder with a high PG grade was used. However, since the individual physical property showed a relatively low correlation, various properties were used together in regression analysis. The estimation models of DTS and ITS were over 0.99, respectively. R2 of MR and SI estimation models were over 0.91 and 0.93, respectively. It was concluded that mechanical properties could be estimated with a high coefficient of determination from those physical properties.

• Applied Chemistry for Engineering
• /
• v.35 no.4
• /
• pp.309-315
• /
• 2024

Silicon and carbon composite (SiC) is considered one of the most promising anode materials for the commercialization of Si-based anodes, as it could simultaneously satisfy the high theoretical capacity of Si and the high electronic conductivity of carbon. However, SiC active material undergoes repeated volumetric changes during charge/discharge processes, leading to continuous electrolyte decomposition and capacity fading, which is still considered an issue that needs to be addressed. To solve this issue, we suggest a 4,4'-Methylenebis(cyclohexyl isocyanate) (H₁₂MDI)-based waterborne polyurethane binder (HPUD), which forms a 3D network structure through thermal cross-linking reaction. The cross-linked HPUD (denoted as CHPU) was prepared using an epoxy ring-opening reaction of the cross-linker, triglycidyl isocyanurate (TGIC), via simple thermal treatment during the SiC anode drying process. The SiC anode with the CHPU binder, which exhibited superior mechanical and adhesion properties, not only demonstrated excellent rate and cycling performance but also alleviated the volume expansion of the SiC anode. This work implies that eco-friendly binders with cross-linked structures could be utilized for various Si-based anodes.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.21 no.3
• /
• pp.27-34
• /
• 2017

Recently, the importance of the industrial warehouse floor has been increasing due to the development of the distribution and logistics industry. In this present study, an early-hardening polymer floor mortar which can compensate for the limitation of conventional cement based floor mortar regarding fluidity and long curing time was developed. In order to achieve the early-hardening of mortar characteristic ultra rapid hardening cement was used as binder. Four types of mixture proportions in accordance with the vinyl acetate ethylene(VAE) polymer contents with range from 10% to 20% and the other proto proportion without VAE polymer were designed. Mechanical experiments including the fluidity test, compressive strength test, bending test, bond test, and abrasion test were conducted for all mixture proportions. From the flow test result, it was possible to achieve the high flow with 250 mm by controlling the amount of superplasticizer. The incorporation of VAE polymer was found to affect the compressive strength reduction, however, the flexural strength was higher than that of the proto mixture, and it was evaluated to increase the compressive strength / flexural strength ratio. Moreover, at least 2.6 times higher bond strength and more than 4 times higher abrasion resistance were secured. From the mechanical experiments results, the optimum mixing ratio of the VAE polymer was determined to be 10%. As a result of application and monitoring, it shows that it has excellent resistance to cracking, discoloration, impact, and scratch as well as bond performance compared to the cement based floor mortar.

• Korean Journal of Optics and Photonics
• /
• v.20 no.2
• /
• pp.123-127
• /
• 2009

In order to improve the diffraction efficiency of the photopolymer, we prepared a $TiO_2$ added photopolymer and investigated the optical properties. Prepared photopolymer films are based on polyvinyl alcohol (PVA) as a polymer binder, acryl amide (AA) as a photo-polymerizable monomer, triethanolamine (TEOA) as an initiator, and eosin Y as a sensitizer at 532 nm. To prepare the photopolymer films with the uniform thickness, the constant amount (2.5 ml) of the photopolymer solution was dropped on the glass and spread using a spin coater. Then films were dried for 72 hrs in a darkroom ($20^{\circ}C$, 40% RH) prior to the optical measurement. Then, the diffraction efficiencies of both the photopolymer films containing $TiO_2$ and non-contained films were measured with the various incident angles ($20{\sim}70^{\circ}$). Therefore, $TiO_2$ added photopolymer showed 5% higher diffraction efficiency than neat photopolymer without $TiO_2$ addition. The addition of $TiO_2$ into the photopolymer showed the high diffraction efficiency (over 70%) at broad range ($20{\sim}70^{\circ}C$) of the incident angle.

• Polymer(Korea)
• /
• v.27 no.6
• /
• pp.549-554
• /
• 2003

Emeraldine salt of polyaniline-dodecylbenzenesulfdnic acid (PANI-DBSA) in organic solvents such as toluene and xylene was obtained by a direct one-step emulsion polymerization technique. When the molar ratio of DBSA to aniline monomer was 1.5:1, its solubility and electric property showed a maximum value and then the solid contents of PANI-DBSA was 8 wt% in toluene. The cast film of PANI-DBSA with no binder was obtained on glass or plastic substrates under ambient conditions. PANI solution can be also easily blended with polyurethane and polystyrene polymers in toluene. Improved electrical performance up to 5 S/cm was achieved with good light-transmittance up to 70% at 500 m thickness. They also showed more homogeneous morphology than that prepared with PANI-DBSA kom aqueous dispersion polymerization. The partially dispersed PANI-DBSA showed particles sizes of 50-400 m in organic solvents and their XRD pattern were observed from the powder sample.

• International Journal of Highway Engineering
• /
• v.18 no.2
• /
• pp.61-71
• /
• 2016

PURPOSES: The objective of this study was to determine the optimum ratio of mix design, for a reclaimed asphalt pavement (RAP) content of 100%, for spray injection application. METHODS: A literature review revealed that spray injection is an efficient and cost-effective application for fixing small defective regions of an asphalt pavement. Rapid-setting polymer-modified asphalt mixtures prepared from two types of rapid-setting polymer asphalt emulsion were subjected to Marshall stability and wet track abrasion tests, in order to identify the optimum mix designs. RESULTS and CONCLUSIONS : Different mix designs of type A and type B emulsions were prepared using RAP and virgin aggregates, in order to compare the performance and determine the optimum mix design. The performance of mixtures prepared with RAP was superior to that of mixtures containing virgin aggregates. Moreover, for optimum ratio of the design, the binder content prepared from RAP was set to 1~2% lower than that consisting of virgin aggregates. Compared to their Type A counterparts, type B mixtures consisting of a reactive emulsion performed better in the Marshall stability and wet track abrasion tests. The initial results confirmed the advantages associated with using RAP for spray injection applications. Further studies will be performed to verify the difference in the optimum mix design and performance obtained in the lab-scale test and tests conducted at the job site by using the spray injection machine.

• Journal of Electrochemical Science and Technology
• /
• v.13 no.3
• /
• pp.362-368
• /
• 2022

The application of polymer composite electrolyte in all-solid-state lithium-sulfur battery (ASSLSBs) can guarantee high energy density and improve the interface contact between electrolyte and electrode, which has a broader application prospect. However, the inherent insulation of the sulfur-cathode leads to a low electron/ion transfer rate. Carbon materials with high electronic conductivity and electrolyte materials with high ionic conductivity are usually selected to improve the electron/ion conduction of the composite cathode. In this work, PEO-LiTFSI-LLZO composite polymer electrolyte (CPE) with high ionic conductivity was prepared. The ionic conductivity was 1.16×10^-4 and 7.26×10^-4 S cm^-1 at 20 and 60℃, respectively. Meanwhile, the composite sulfur cathode was prepared with Sulfur, reduced graphene oxide and composite polymer electrolyte slurry (S-rGO-CPEs). In addition to improving the ion conductivity in the cathode, CPEs also replaces the role of binder. The influence of different contents of CPEs in the cathode material on the performance of the constructed battery was investigated. The results show that the electrochemical performance of the all-solid-state lithium-sulfur battery is the best when the content of the composite electrolyte in the cathode is 40%. Under the condition of 0.2C and 45℃, the charging and discharging capacity of the first cycle is 923 mAh g^-1, and the retention capacity is 653 mAh g^-1 after 50 cycles.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.11-11
• /
• 2009

본 연구는 MLCC 제조공정중 그린상태에서의 강도를 유지하기 위한 고분자 바인더의 거동을 예측하고, 제조공정중 나타난 가열후 수축 현상을 규명하고자 하였다. 이를 위해 메커니즘에 대한 가설을 수립하고 이를 여러가지 분석기법과 컴퓨터 시뮬레이션을 통해 확인하였으며, 현장의 제조기술 부문에서 용이하게 사용할 수 있도록 간단한 수학적 모델링으로 표현하였다. 수학적 모델링은 제품을 이용한 실험과 비교하여 정확도를 검증하였으며, 이러한 해석기법은 대표체적요소(representative volume element)을 이용하여 MLCC 그린바 (Bar)의 해석까지 가능하도록 응용범위를 향상시켰다.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.4
• /
• pp.229-237
• /
• 1996

Porous matrices for PAFC were prepared with chemically synthesized polyaniline powders. Phosphoric acid doped polyaniline showed decreasing electric conductivities as the temperature increased. Above $100^{\circ}C$, it showed negligible conductivities. It was stable in phosphoric acid up to $250^{\circ}C$. SiC powders or SiC whiskers were added to polyaniline to decrease the thermal expansion of polyaniline. 10% of polytetrafluoroethylene(PTFE) was also added as a binder. The bubble pressures and wettabilities of matrices were investigated and compared with the porosities measured by porosimeter. Based on these data, the optimum manufacturing condition was determined. The bubble pressure of the matrix made by adding 25w/o SiC whiskers was 345mmHg, the wettability was 235w/o, and the porosity was 83%. In the unit cell operation, the performances of polyaniline matrices were as good as those of SiC matrices. This result suggested that polyaniline can be a possible candidate for the matrix material of PAFC.