용해성 PMDA/diamine/dianhydride 폴리이미드를 제조하여 특성을 고찰하고, 상용 알루미나 세라믹막내에 제조한 PMDA/diamine/dianhydride 용액을 코팅하여 기체투과특성을 알아보았다. Tg는 $337{\sim}358^{\circ}C$의 범위로 열적안정성은 우수함을 보였다. 용해성에 있어서는 NMP, DMAc, DMSO, THF, m-cresol의 극성 용매에 대해 대부분 좋은 결과를 보여 주었다. 알루미나막과 용해성 폴리이미드의 점착은 잘 이루어졌으며, 기체투과실험에 있어 6FDA를 포함한 폴리이미드의 경우 높은 투과도를 보였다. PMDA/1,3PDA/6FDA의 경우 질소투과도는 약 $7.6{\times}10^{-7}(mol/m^2{\cdot}Pa{\cdot}s)$의 값을 나타내었고, 질소에 대한 산소의 이상적 분리도, $P(O_2/N_2)$는 6.19였으며, $P(H_2/N_2)$의 경우는 약 70.0의 이상적 분리도를 보였다.
본 연구는 폴리이미드와 폴리이서설폰 중공사막을 이용하여 매립가스의 메탄 회수를 위한 메탄과 질소에 대한 투과도와 선택도를 실험하였다. 폴리이미드와 폴리이서설폰 소재를 건/습식 상전이 법을 이용하여 중공사 형태로 제조하고 표면 실리콘 코팅 후 모듈을 제조하였다. 전자주사 현미경 관찰을 이용하여 제조된 중공사 막의 구조가 치밀한 표면과 망상구조의 비대칭으로 형성된 것을 확인하였다. 압력과 온도가 증가함에 따라 메탄과 질소의 투과도는 증가하였으나 선택도($CH_4/N_2$)는 감소하는 것으로 나타났다. Air gap이 증가할수록 메탄과 질소의 투과도는 감소하였으며 용매치환을 한 중공사막의 투과도는 3.2~7.0배 증가하였다.
In this paper, we demonstrate that the organic electrophosphorescent device is driven by the organic thin film transistor with spin-coated photoacryl gate insulator. It was found that electrical output characteristics in our organic thin film transistors using the staggered-inverted top-contact structure showed the non-saturated slope in the saturation region and the sub-threshold nonlinearity in the triode region, where we obtained the maximum power luminance that was about 90 $cd/m^2$. Field effect mobility, threshold voltage, and on-off current ratio in 0.45 ${\mu}m$ thick gate dielectric layer were 0.17 $cm^2/Vs$, -7 V, and $10^6$ , respectively. In order to form polyimide as a gate insulator, vapor deposition polymerization process was also introduced instead of spin-coating process, where polyimide film was co-deposited by high-vacuum thermal evaporation from 4,4'-oxydiphthalic anhydride (ODPA) and 4,4'-oxydianiline (ODA) and cured at 150${\sqsubset}$for 1hr. It was also found that field effect mobility, threshold voltage, on-off current ratio, and sub-threshold slope with 0.45 ${\mu}m$ thick gate dielectric films were 0.134 $cm^2/Vs$, -7 V, and $10^6$ A/A, and 1 V/decade, respectively.
In Liquid Crystal Display (LCD) manufacturing, the organic over coat materials over coat materials for insulation layer of color filter with acryl ate was widely used. Therefore, we approach that the organic overcoat material can use to insulation layer for color filter and liquid crystal (LC) alignment layer in this research. The LC aligning capabilities was successful stuided for the first time. The organic overcoat layer and polymer layer was coated by spin-coating. In order to characterize the LC alignment, electric optic and residual DC and atomic force microscopy (AFM) image was used. The good LCD aligning capabilities treated on the organic overcoat thin film surfaces with ion beam exposure of $45^{\circ}$ above ion beam energy density of 1200 eV can be achieved. Also the good LCD alignment capabilities treated polymer on surfaces with ion beam exposure of $45^{\circ}$ above ion beam energy density of 1800 eV can be achieved. Comparing electro-optical characteristics between the Polyimide (PI) and the overcoat, the resultant transmittance of the overcoat considerably matched that of the PI and the residual DC also exhibited similar features with the PI.
본 연구에서는 고분자 막을 이용하여 6대 온실가스 중 가장 높은 지구온난화지수를 갖는 육불화황(sulfur hexafluoride, $SF_6$)의 회수에 관한 연구를 실시하였다. 막 소재로 이미드 계열의 Matrimid 5218 소재를 건/습식 상전이 법을 이용하여 중공사 형태로 제조하고, 표면 실리콘 코팅 후 모듈을 제조하였다. 제조된 중공사 막은 전자주사현미경 관찰을 통하여 외부 표면에 치밀한 선택층과 망상구조의 하부로 이루어진 비대칭 구조를 확인하였다. 막의 기체투과 특성 확인을 위하여 온도와 압력 변화에 따른 $N_2$, $SF_6$ 단일 기체투과를 실시하였으며, 운전 조건에 따라서 0.78~1.36 GPU의 $N_2$ 투과도와 2.44-5.08의 $N_2/SF_6$ 선택도를 나타냈었다. 제조된 모듈의 혼합기체 분리거동 관찰을 위하여 10 vol.% $SF_6$ 농도를 갖는 $N_2/SF_6$ 혼합기체를 이용하여 온도, 압력, retentate 유량을 달리하여 실시하였으며, 실험을 통하여 압력과 온도 증가 및 retentate 유량 감소에 따라서 회수된 가스 중에 $SF_6$의 농도는 증가되어 최고 37.5 vol.%를 나타낸 반면 회수율은 감소되는 경향을 나타내었으며, 동일한 온도와 압력에서 retentate 유량 증가에 따라서 $SF_6$ 농도는 감소되는 반면 회수율이 증가하여 최고 89%의 회수율을 나타내었다.
금속 발열체는 높은 열손실과 화재 위험성 등의 문제점이 있어 우수한 열전도도와 전기전도도 특성을 갖는 탄소섬유가 대체소재로 각광받고 있다. 그러나 탄소섬유는 약 200℃ 이상에서 산화하여 단선되기 때문에 발열체 적용이 제한적이며, 현재 진공관 형태로 탄소섬유 발열체가 일부 사용되고 있다. 본 연구에서는 진공관을 사용하지 않고 대기 중탄소섬유 산화방지를 위해 전기영동증착법으로 탄소섬유 표면에 내열성이 높은 폴리이미드를 코팅하였으며 인가전압에 따른 코팅 두께와 내열성을 확인하였다. 폴리이미드를 코팅한 탄소섬유 발열체를 직렬 연결하여 만든 히터는 최대 292℃ 까지 안정적인 발열 특성을 보였으며 이는 열전달 시뮬레이션의 발열온도 결과와 유사하였다. 전기영동증착방법으로 코팅한 폴리이미드 층은 200℃ 이상에서 탄소섬유의 산화방지에 효과적이며 발열 안정성을 요구하는 2차전지, 우주항공, 전기자동차 등 다양한 발열 부품에 적용 가능할 것으로 기대된다.
Membrane electrode assembly (MEA) for polymer electrolyte fuel cell (PEFC) are commonly prepared in the research laboratory by spraying, screen-printing and brushing catalyst slurry onto membrane or other support material like carbon paper or polyimide film in a batch style. These hand applications of the catalyst slurry are painstaking process with respect to precision of catalyst loading and reproducibility. It has been generally mentioned that the adoption of continuous process is very helpful to develop the reliable product. In the present work, we report the results of using continuous type coater with doctor-blade to coat catalyst slurry for preparing the MEA catalyst layers In a faster and highly reproducible fashion. We show that while expectedly faster than batch style, the machine coater requires the use of slurry of appropriate composition and a properly selected transfer decal material in order to achieve superior MEA plat lnw loading reproducibility. To make highly viscous catalyst slurry that is imperative for using coater, we use 40wt.% Nafion solution and minimize the content of organic solvent. And the choice of proper high surface area catalyst is important in the viewpoint of making well-dispersed slurry. After catalyst coating onto the support material, we transferred the catalyst layer to both sides of Nafion membrane by hot-pressing In this case, the degree of transfer was Influenced by hot-pressing condition including temperature, pressure, and time. To compare the transferring ability, we compared so many films and detaching papers. And among the support, polyethylene terephthalate(PET) film shows the prominent result.
This work aims to develop a dry lubricant for oilless bush, especially a solid lubricant, thereby creating a coating method with improved properties of anti-friction and load-carrying capacity without oil lubrication. In this work, spherical-shaped powders of thermosetting resin such as polyimide (PI) are mixed with a binder matrix obtained by mixing a fluorocarbon compound resin such as Polytetrafluoroethylene (PTFE) or Ethylene tetra fluoro ethylene (ETFE) with itself or with a non-fluorocarbon thermoplastic resin such as Polyether ether ketone (PEEK). And these dry lubricant mixtures are thickly coated (200-300 mm in the thickness) on the inner surface of the bush by using a wet-typed air-spray deposition method. It was found that the load-carrying capacity of the solid lubricant for excavator bush (60 mm in diameter) that operates under a high load condition (at 40 MPa) is greatly improved owing to the spherical-shaped powders of thermosetting resin. In addition, the coefficient of friction at the sliding surface is also reduced less than 0.1. Thick coating also lowers the contact stress at the edge of a bush that results in better tribological performances. The result suggests that the lubrication performance and durability life of the bush can be remarkably improved even without lubrication (oil or grease).
Kim, D.;J. Sung;H. M. Cheong;C. N. Whang;Y. Ouchi;T. limori;N. Matsuie;K. Seki
한국진공학회지
/
제12권S1호
/
pp.70-73
/
2003
Sum-frequency vibrational spectroscopy has recently been used to investigate the surface of the various polymers and was able to find the chemical compositions and structures specific to the surface. Here we report our studies on two specific polymer samples to demonstrate its capability. Polyimide thin films were made by spin coating on fused quartz and $CaF_2$ substrates. The sum-frequency signal originating mainly from the air/polymer interface showed markedly different spectra, indicating the structural change of the polymer surface depending on the underlying substrate. Various polyethylene surfaces were also investigated by sum-frequency vibrational spectroscopy. The surface of polyethylene samples in the CH-region showed different sum-frequency spectra, presumably due to the trace amount of additives having much higher concentration at the air/polymer interface. These examples demonstrate the surface and interface of the polymer could have different structure and chemical composition from those of a bulk, which can be studied effectively by surface nonlinear optical spectroscopy.
TCP(Tape Carrier Package), COG (Chip On Glass), COF(Chip On Film) are three methods for connecting LDI(LCD Driver IC) with LCD panels. Especially COF is growing its portion of market place because of low cost and fine pitch correspondence. But COF has a problem of the lead broken failure in LCD module process and the usage of customer. During PCB (Printed Circuit Board) bonding process, the mismatch of the coefficient of thermal expansion between PCB and D-IC makes stress-concentration in COF lead, and also D-IC bending process during module assembly process makes the level of stress in COF lead higher. As an affecting factors of lead-broken failure, the effects of SR(Solder Resister) coating on the COF lead, surface roughness and grain size of COF lead, PI(Polyimide) film thickness, lead width and the ACF(Anisotropic Conductive Film) overlap were studied, The optimization of these affecting manufacturing processes and materials were suggested and verified to prevent the lead-broken failure.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.