• Applied Chemistry for Engineering
• /
• v.21 no.5
• /
• pp.532-536
• /
• 2010

A study on the volatile organic compounds (VOCs) and low molecular weight (LMW) amount which is contained within bisphenol A polycarbonate (PC) was performed by the solvent extraction with ketone type solvents (acetone, butanone, pentanone). The LMW amount of untreated PC was 2.6 wt%, but the values of treated samples with acetone and pentanone were 0.96 and 1.53 wt%, respectively. Acetone is a more effective solvent than pentanone on the LMW extraction. Methylene chloride (MC) and toluene were certified and quantified by GC-Mass experiments, and the quantitative results indicated the fact that the pentanone was the effective solvent on VOC extraction. Focused on the change of VOCs and LMW amount, the use of co-solvent might be more useful, and the experimental results of co-solvent extraction showed that the optimum condition was 50 : 50 volume percent.

• Korean Journal of Materials Research
• /
• v.19 no.8
• /
• pp.421-426
• /
• 2009

We report on the capacitively coupled O2 plasma etching of PMMA and polycarbonate (PC) with a diffusion pump. Plasma process variables were process pressure and CCP power at 5 sccm $O_2$ gas flow rate. Characterization was done in order to analyze etch rate, etch selectivity, surface roughness, and morphology using stylus surface profilometry and scanning electron microscopy. Self bias decreased with increase of process pressure in the range of 25$\sim$180 mTorr. We found an important result for optimum pressure for the highest etch rate of PMMA and PC, which was 60 mTorr. PMMA and PC had etch rates of 0.46 and 0.28 ${\mu}m$/min under pressure conditions, respectively. More specifically, etch rates of the materials increased when the pressure changed from 25 mTorr to 60 mTorr. However, they reduced when the pressure increased further after 60 mTorr. RMS roughnesses of the etched surfaces were in the range of 2.2$\sim$2.9 nm. Etch selectivity of PMMA to a photoresist was $\sim$1.5:1 and that of PC was $\sim$0.9:1. Etch rate constant was about 0.04 ${\mu}m$/minW and 0.02 ${\mu}m$/minW for PMMA and PC, respectively, with the CCP power change at 5 sccm $O_2$ and 40 mTorr process pressure. PC had more erosion on the etched sidewall than PMMA did. The OES data showed that the intensity of the oxygen atomic peak (777.196 nm) proportionally increased with the CCP power.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.31-35
• /
• 2003

폴리카보네이트는 내열성과 투명성이 우수한데 비해 내후성이 좋지 않아 황변 및 물성이 저하되고, 내찰상성이 약하여 긁히기 쉬운데다 이물질에 의해 오염되기 쉬워 투명성이 저하되는 문제점이 있다. 이러한 단점을 극복하고, 사용하는 용도에 따라 요구되는 다양한 기능성을 부여하기 위하여 폴리카보네이트 표면에 기능성층을 형성시킴으로써 그 목적을 달성하고자 한다. 본 논문에서는 이온 주입기술을 이용하여, 폴리카보네이트 표면의 전기전도도 특성을 향상시키고, 피부암 및 백내장 등을 유발하는 유해한 자외선 (UV-A, UV-B)을 차단하려 한다. 표면전기전도도의 향상은 이물질로부터 오염되는 정도를 낮추며, 정전기를 방지할 수 있다. PC(Polycarbonate) 표면에 $N^+,\;Ar^+,\;Kr^+,\;Xe^+$ 이온을 에너지 20keV에서 50keV을 사용하여, 주입량 $5{\times}10^{15}\;{\sim}\7{\times}10^{16}\cm^2$ 로 조사하였다. 이온 주입된 PC의 표면을 두 접점 방법의 표면 저항 측정으로 표면전기전도도 특성을 알아보았고, 자외선차단 특성은 UV-Vis 로 분석하였다. 이들 전기적 광학적 특성간의 상관관계를 관찰하고, 이러한 특성을 나타내는 화학적 기능그룹들의 변화를 보기 위해 FTIR 분석법으로 관찰하였다. 이온조사량의 증가에 따라 표면저항은 $10^7{\Omega}/sq$까지 감소하여 표면전기특성을 증가시키며, 자외선 차단 특성은 UV-A를 95%까지 차단하여 인체에 유해한 자외선 차단에 유용함을 확인하였다. 이러한 특성은 PC 표면에 카본 네트워크 형성과 $\pi$전자들의 운동량을 증가시키는 구조로 고분자 사슬들의 결합구조 변형에 의한 것으로 생각된다.블을 가지고 파서를 설계하였다. 파서의 출력으로 AST가 생성되면 번역기는 AST를 탐색하면서 의미적으로 동등한 MSIL 코드를 생성하도록 시스템을 컴파일러 기법을 이용하여 모듈별로 구성하였다.적용하였다.n rate compared with conventional face recognition algorithms. 아니라 실내에서도 발생하고 있었다. 정량한 8개 화합물 각각과 총 휘발성 유기화합물의 스피어만 상관계수는 벤젠을 제외하고는 모두 유의하였다. 이중 톨루엔과 크실렌은 총 휘발성 유기화합물과 좋은 상관성 (톨루엔 0.76, 크실렌, 0.87)을 나타내었다. 이 연구는 톨루엔과 크실렌이 총 휘발성 유기화합물의 좋은 지표를 사용될 있고, 톨루엔, 에틸벤젠, 크실렌 등 많은 휘발성 유기화합물의 발생원은 실외뿐 아니라 실내에도 있음을 나타내고 있다.>10)의 $[^{18}F]F_2$를 얻었다. 결론: $^{18}O(p,n)^{18}F$ 핵반응을 이용하여 친전자성 방사성동위원소 $[^{18}F]F_2$를 생산하였다. 표적 챔버는 알루미늄으로 제작하였으며 본 연구에서 연구된 $[^{18}F]F_2$가스는 친핵성 치환반응으로 방사성동위원소를 도입하기 어려운 다양한 방사성의 약품개발에 유용하게 이용될 수 있을 것이다.었으나 움직임 보정 후 영상을 이용하여 비교한 경우, 결합능 변화가 선조체 영역에서 국한되어 나타나며 그 유의성이 움직임 보정 전에 비하여 낮음을 알 수 있었다. 결론: 뇌활성화 과제 수행시에 동반되는 피험자의 머리 움직임에 의하여 도파민 유리가 과대평가되었으며 이는 이 연구에서 제안한 영상정합을 이용한 움직임 보정기법에 의해서 개선되었다. 답이 없는 문제, 문제 만들기, 일반화가 가능한 문제 등으

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.314-325
• /
• 2000

Thermal degradation of thermoplasitc polyurethane modified polycarbonate has been investigated by means of DSC, GPC and FT-IR techniques. The polyurethanes used in this study are TPU-35 and TPU-53 containing 35.5 and 53.4 wt% of hard segments, respectively. The more content of hard segment, the higher the glass transition temperature (T$_{g}$) of TPU was observed. On the other hand, the T$_{g}$ of the TPU modified PC decreased with the content of TPU and the annealing temperature regardless of the hard segment contents. The latter behavior nay arise from the thermal degradation of TPU upon annealing process: the observed thermal degradation temperatures were at 240 and 25$0^{\circ}C$ for the PC/TPU-35 and PC/TPU-53, respectively. The molecular weight, molecular weight distribution and viscosity agree well with the DSC measurement, which implicates a thermal degradation of TPU. In addition, thermal stability of the TPU modified PC linearly decreased with an incorporation of TPU. Transesterification or any interaction was not observed using FT-IR: the evidence was no frequency shift or any variance betwere the carbonyl stretching and NH group. For the specimens prepared below the degradation temperature, the enhancement of the thickness dependent impact strength of the PC/TPU blend was observed, and the morphology of the two blends was compared.d.

• Polymer(Korea)
• /
• v.24 no.3
• /
• pp.389-398
• /
• 2000

Transparent, abrasion resistant coatings with 4~13 ${\mu}{\textrm}{m}$ thickness were prepared by spin-coating on polycarbonates with organic/inorganic hybrid solutions, followed by UV curing and heat treatment at 12$0^{\circ}C$ for 12 hours. The coating solutions were composed of inorganic phase and organic phase in 0:100, 20:80, 30:70, 50:50, 80:20 wt% ratios, respectively, mixed with photoinitiator, senaitizer and surfactant. The inorganic phase was formed by sol-gel reaction of TEOS and silane coupling agent MPTMS in 1 : 2 or 2 : 1 molar ratios, the organic phase consisted of difunctional urethane acrylate oligomeric resin, multifunctional acrylate TMPTA and HDDA in 4 : 3 : 3 wt% ratio. The coating systems were investigated by FT-IR, $^{29}$ Si-NMR spectra. In addition, TGA/DSC for thermal analysis and SEM, AFM observation for coated surface were examined. Gererally, the homogeneity of phases, the surface smoothness of coating and abrasion resistance were improved with the higher content of inorganic component. Namely, coating system with below 10 $\AA$ surface roughness and T$_{g}$ of 15$0^{\circ}C$ showed only 10% decrease in light transmittance after abrasion test, whereas uncoated polycarbonate substrate exhibited 46% decrease..

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.24 no.3
• /
• pp.107-112
• /
• 2018

The purpose of this study was to investigate the migration levels of lead (Pb), cadmium (Cd) and arsenic (As) from polycarbonate food contact materials into food simulant at different temperatures ($70^{\circ}C$ and $100^{\circ}C$). The method was validated by linearity of calibration curves, limit of detection (LOD), limit of quantification (LOQ), recovery, precision and uncertainty. All of 200 samples, including bottles, cups, containers, ladles, spoons and tongs were purchased from domestic markets and analyzed by inductively coupled plasma mass spectrometry (ICP-MS). Mean concentrations of positive samples were higher at $100^{\circ}C$ than $70^{\circ}C$ as showing a dependency of migration temperature. The migration concentrations ranged from not-detected (ND) to $4.67{\mu}g/L$, ND to $0.49{\mu}g/L$L and ND to $2.91{\mu}g/L$ for Pb, Cd and As, respectively, which were far below the migration limits of Korea standards and specifications for food utensils, containers and packages.

• Proceedings of the Optical Society of Korea Conference
• /
• 2002.07a
• /
• pp.214-215
• /
• 2002

최근 들어 polymer는 여러 분야에 응용되고 있으며 광학적 시스템에도 널리 사용되고 있다. 주로 사용되는 polymer에는 PMMA(Poly methyl methacrylate), PC(Polycarbonate), PS(polystyrene)[1] 등이 있다. Optical Polymer는 제작이 용이하고 크기에 제한을 받지 않아 그 수요가 크게 확대되고 있다. 광학적인 시스템에 사용되기 위해서는 높은 순도가 요구되면서 또한 재질의 균일성이 확보되어야 한다. 본 연구에서는 간섭계를 구성하여 복굴절을 측정하고 이러한 복굴절에 기인하는 비대칭 수차의 평가를 통하여 광학적인 시스템에 미치는 영향을 분석하였다. (중략)

• Proceedings of the Korean Fiber Society Conference
• /
• 2002.04a
• /
• pp.263-264
• /
• 2002

무정형 고분자인 폴리카보네이트는 투명하고 뛰어난 기계적 성질(특히 내충격성) 내열성 내한성ㆍ전기적 성질을 균형 있게 갖추고, 무독하고 자기소화성(自己消火性)도 있는 엔지니어링 플라스틱이다. 본 연구의 목적은 이러한 특성을 가지는 폴리카보네이트를 이용하여 전기방사법으로 sub-micron의 섬유직경으로 구성된 부직포를 제조하는데 있다. (중략)

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.829-830
• /
• 2012

• Proceedings of the PSK Conference
• /
• 2003.04a
• /
• pp.118.2-119
• /
• 2003

This study was undertaken to assess overall effects of bisphenol A, a monomer widely used in manufacturing polycarbonate plastics or epoxy resin, exposure on immune system of mice. For in vitro evaluation, serial concentration of SPA was added into culture of various immune cells from normal female ICR mice, and for in vivo or ex vivo assessment, mice were orally exposed to BPA dissolved in olive oil as doses of 500, 1000, 2000 mg/g b.w. for acute expose or 100, 500, 1000 mg/kg/day b.w. 5days a week for subacute exposure. (omitted)