• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.9
• /
• pp.931-935
• /
• 2012

In this study, we fabricate and investigate low-temperature solid oxide fuel cells with a ceramic substrate/porous metal/ceramic/porous metal structure. To realize low-temperature operation in solid oxide fuel cells, the membrane should be fabricated to have a thickness of the order of a few hundreds nanometers to minimize IR loss. Yttrium-doped barium zirconate (BYZ), a proton conductor, was used as the electrolyte. We deposited a 350-nm-thick Pt (anode) layer on a porous substrate by sputter deposition. We also deposited a 1-${\mu}m$-thick BYZ layer on the Pt anode using pulsed laser deposition (PLD). Finally, we deposited a 200-nm-thick Pt (cathode) layer on the BYZ electrolyte by sputter deposition. The open circuit voltage (OCV) is 0.806 V, and the maximum power density is 11.9 mW/$cm^2$ at $350^{\circ}C$. Even though a fully dense electrolyte is deposited via PLD, a cross-sectional transmission electron microscopy (TEM) image reveals many voids and defects.

• Korean Journal of Materials Research
• /
• v.9 no.5
• /
• pp.484-490
• /
• 1999

$(Pb,La)TiO_3$(PLT) thin films were prepared on Pt/SiO$_2$/Si substrates by the sol-gel method and investigated the crystalline and electrical properties according to La concentration and post-annealing temperatures. The PLT films annealed at above $600^{\circ}C$ were exhibited the typical perovskite structures regardless of La contents. When the $(Pb,La)TiO_3$(PT) films were doped with La concentration up to 10mol%(PLT-10), the degree of z-axis orientation was greatly decreased from 63% to 26%. From AES depth profiles for the PLT-10 samples, no remarkable inter-reaction between PLT film and lower Pt electrode was found. The remanent polarization$(2Pr,Pr_+-Pr_-)$ were increased from $4\muC\textrm{cm}^2 to 16\muC\textrm{cm}^2$ as the annealing temperature increased from $600^{\circ}C to 700^{\circ}C$. This result may be ascribed to the improvement of crystallinity by the high temperature post-annealing. The dielectric constant$({\varepsilon}r)$ and tangent loss(tan$\delta$) of the PLT-10 films annealed at $650^{\circ}C$ were about 193 and 0.02, respectively with the pyroelectric coefficient($\gamma$) of around $4.0nC/\textrm{cm}^2{\cdot}^{\circ}C at 30^{\circ}C$.

• Journal of the Korea Concrete Institute
• /
• v.21 no.5
• /
• pp.565-572
• /
• 2009

In this study, corrosion resistance of palm oil fuel ash (POFA) concrete as a blended concrete is evaluated by using electrochemical technique. The POFA is an industrial byproduct obtained from fuel ash after extracting palm oil from palm-tree. In order to obtain basic material characteristics of the POFA concrete, tests on compressive strength, slump, weight loss, bleeding and expansion ratio were carried out the early-aged POFA concrete. On the other hand, durability characteristics, both chloride penetration and carbonation depth test, were also conducted. Finally, corrosion resistance were evaluated by applying electro-chemical artificial crack healing technique, and the tests on the impressed voltage characteristic, galvanic current and linear polarization resistance. From the experimental results, it was found that long-term strength, bleeding, lower slump ratio, expansion ratio, chloride penetration, carbonation and corrosion resistance were improved by using the POFA due to activated pozzolanic reaction. It can be also mentioned that POFA concrete has a potential to be used as a cementitious binder for green-recycling resources.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.3
• /
• pp.93-98
• /
• 2005

The crystal growth of calcite at a low temperature range was carried out by the hydrothermal method using amorphous calcium carbonate which has excellent solubility in water. Amorphous calcium carbonate was prepared by the wet chemical reaction of a stoichiometric mixture of $CaCl_2\;and\;Na_2CO_3$. An important factor was the reaction temperature and time taken in preparation of the amorphous calcium carbonate. From the solubility results calculated by the weight loss method, $NH_4NO_3$ solutions were found to be the most promising solvents to grow calcite single crystals. The hydrothermal conditions for high growth rates of calcite single crystals were as follows: starting material: amorphous calcium carbonate, solvent: 0.01 m $NH_4NO_3$, temperature: $180^{\circ}C$, duration: 30 days. And properties of calcite single crystals were follows: dislocation density: $10^6{\sim}10cm^{-2}$, UV-visible transmittance: about 80% from 190 to 400 nm and birefringence: $0.17{\sim}0.18$. Also, it can be known from the FT-IR results that the absorption peak by injection of $HCO_3^-\;and\;OH^-$ ions was not shown.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.5
• /
• pp.23-30
• /
• 2000

To compensate the nonlinearity of electroabsorption modulator(EAM) resulting from its near exponential transfer function, a semiconductor optical amplifier(SOA) that has a log transfer function is used. Since the transfer function of SOA is inverse to that of EAM, the intermodulation distortion(IMD) of EAM can be reduced by cascading SOA to EAM. Also, the RF gain can be increased by the optical gain of SOA. For these reasons, spurious free dynamic range(SFDR) of EAM is enhanced by connecting SOA to EAM in series and operating in gain salutation region. To improve the nonlinearity compensation of EAM, the increased gain of SOA is required and the slope of gain saturation, the ratio of gain to input SOA power, needs to be steep. However, signal spontaneous beat noise that is the dominant system noise increases in proportion to the gain such that the SFDR of EAM is reduced. The higher the gain of SOA is, the more ASE is increased. Thus the noise level of system is increased and the following SFDR of EAM is decreased. The slope of gain saturation region and ASE of have trade-off relation and the optimization is achieved at 8㏈ optical gain. 9㏈ enhancement of SFDR of EAM is obtained. This scheme is easy to embody the linear EAM and the integration with three components (DFB-LD, EAM and SOA) offers many merits, such as low insertion loss, low chirping and low polarization sensitivity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.11
• /
• pp.1178-1185
• /
• 2004

In the atmosphere of $N_2$ gas, BaZ $r_{0.08}$ $Ti_{0.92}$ $O_3$ polycrystal was grown by floating zone technique using BaZ $r_{0.08}$ $Ti_{0.92}$ $O_3$ ceramics as a feed and SrTi $O_3$(1l0) single cystal as a seed. The dielectric constant and loss at 10 kHz, 100 kHz, and 1 MHz for the as-grown sample were measured as a function of temperature in the temperature range between -10$0^{\circ}C$ and 150 $^{\circ}C$ to find a dielectric peak with frequency dispersion at Curie point. The hysteresis loop showed that the grown sample had very small polarization which was 0-0.01 $\mu$C/$\textrm{cm}^2$ for the applied dc-electric fields from -7 kV/cm to +7 kV/cm. However, the normal hysteresis loop was appeared after oxygen annealing. The electric-field dependence of the dielectric constant for both the as-grown and the post-annealed samples was studied by measuring the dielectric constants as a function of the biased-electric fields and their tunability was figured out from it at room temperature(27 $^{\circ}C$) and cryotemperature( -73$^{\circ}C$). Tunability for the as-grown sample was 51 % and the figure of merit 20.4 at 10kHz with the biased electric-field of 12 kV/cm. The tunability for the grown sample may be increased up to 80 % if the electric field of 25 kV/cm is applied. Tunability for the post-annealed sample was 41 % and the figure of merit 10.3 at 10 kHz with the biased electric-field of 12 kV /cm. Post-annealing improved the crystallinity of the as-grown sample but decreased its tunability.ability.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.280-280
• /
• 2007

$Pb(Zr,Ti)O_3$ (PZT) 강유전체 박막은 높은 잔류 분극 (remanent polarization) 특성 때문에 현재 강유전체 메모리 (FeRAM) 소자에 적용하기 위하여 가장 활발히 연구되고 있다. 그런데 PZT 물질은 피로 (fatigue) 및 임프린트 (imprint) 등의 장시간 신뢰성 (long-term reliability) 특성이 취약한 단점을 가지고 있다. 이러한 신뢰성 문제를 해결할 수 있는 효과적인 방법 중의 하나는 $IrO_2$, $SrRuO_3$(SRO) 등의 산화물 전극을 사용하는 것이다. 많은 산화물 전극 중에서 SRO는 PZT와 비슷한 pseudo-perovskite 결정구조를 갖고 격자 상수도 비슷하여, PZT 커패시터의 강유전 특성 및 신뢰성을 향상시키는데 매우 효과적인 것으로 알려져 있다. 따라서 본 연구는 PZT 커패시터에 적용하기 위하여 SRO 박막을 증착하고 이의 전기적 특성 및 미세구조를 분석하고자 하였다. 또 실제로 SRO 박막을 상부전극과 PZT 사이의 버퍼 층 (buffer layer)으로 적용한 경우의 커패시터 특성도 평가하였다. 먼저 다결정 SRO 박막을 $SiO_2$/Si 기판 위에 DC 마그네트론 스퍼터링 법 (DC magnetron sputtering method)으로 증착하였다. 그 다음 이러한 SRO 박막의 미세구조, 결정성 및 전기적 특성이 증착 조건들의 변화에 따라서 어떤 경향성을 보이는지를 평가하였다. 기판 온도는 $350\;{\sim}\;650^{\circ}C$ 범위에서 변화시켰고, 증착 파워는 500 ~ 800 W 범위에서 변화시켰다. 또 Ar+$O_2$ 혼합 가스에서 산소의 혼합 비율을 20 ~ 50% 범위에서 변화시켰다. 이러한 실험 결과 SRO 박막의 전기적 특성 및 미세 구조는 기판의 증착 온도에 따라서 가장 민감하게 변함을 관찰할 수 있었다. 다른 증착 조건과 무관하게 $450^{\circ}C$ 이상의 온도에서 증착된 SRO 박막은 모두 주상정 구조 (columnar structure)를 형성하며 (110) 방향성을 강하게 나타내었다. 가장 낮은 전기 저항은 $550^{\circ}C$ 증착 온도에서 얻을 수 있었는데, 그 값은 약 $440\;{\mu}{\Omega}{\cdot}cm$ 이었다. SRO 버퍼 충을 적용하여 제작한 PZT 커패시터의 잔류 분극 (Pr) 값은 약 $30\;{\mu}C/cm^2$ 정도로 매우 높은 값을 나타내었고, 피로 손실 (fatigue loss)도 $1{\times}10^{11}$ 스위칭 사이클 후에 약 11% 정도로 매우 양호한 값을 나타내었다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.5
• /
• pp.301-313
• /
• 2021

Theoretical background for the meaning of various piezoelectric properties can be easily found in a number of textbooks and academic papers. In contrast, how they are actually measured and characterized are rarely described, though this information would be the most important especially to the researchers who just started working on the field. It follows that this report was intended to provide a practical guidance for measuring basic but essential properties of ferroelectric-based piezoelectric materials. The discussion begins with how to measurement dielectric properties such as dielectric permittivity and loss (dissipation factor), followed by piezoelectric properties such as piezoelectric constants, electromechanical coupling factor, and quality factor as well as ferroelectric features, i.e., electric field dependent polarization hysteresis. Though our discussion here is limited to the techniques that are already well-standardized, it is expected to make a seed to be developed into more challenging and creative ones.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.31 no.1
• /
• pp.55-62
• /
• 2021

In order to improve fuel economy and reduce CO2, HEV adopts ISG system as a standard. This ISG system increased the electric load that the battery had to bear, and the number of starting increased rapidly. AGM Lead Acid batteries have been developed and used, but the charging time is about three times longer as the electrolyte amount control during formation must be maintained at a higher level compared to conventional lead-acid batteries. In this study, we tried to shorten the charging time by increasing the charging efficiency through the optimization of the formation pattern. In order to optimize the Formation Pattern, 10 charging steps and 6 discharging steps were applied to 16 multi steps, and the charging current for each step was controlled, and the test was conducted under 4 conditions (21 hr, 24 hr, 27 hr, 30 hr). As a result of simultaneous application of multi-step and discharge step, it was verified that minimizing the current loss and eliminating the sudden polarization during charging contributes to the improvement of charging efficiency. As a result, it showed excellent results in reducing the charging time by about 30 % with improved charging efficiency compared to the previous one.

• Geophysics and Geophysical Exploration
• /
• v.24 no.4
• /
• pp.180-193
• /
• 2021

The complex resistivity method is an exploration technique that can obtain various characteristic information of underground media by measuring resistivity and phase in the frequency domain, and its utilization has recently increased. In this paper, a three-dimensional inversion algorithm for the CR data was developed to increase the utilization of this method. The Poisson equation, which can be applied when the electromagnetic coupling effect is ignored, was applied to the modeling, and the inversion algorithm was developed by modifying the existing algorithm by adopting comlex variables. In order to increase the stability of the inversion, a technique was introduced to automatically adjust the Lagrangian multiplier according to the ratio of the error vector and the model update vector. Furthermore, to compensate for the loss of data due to noisy phase data, a two-step inversion method that conducts inversion iterations using only resistivity data in the beginning and both of resistivity and phase data in the second half was developed. As a result of the experiment for the synthetic data, stable inversion results were obtained, and the validity to real data was also confirmed by applying the developed 3D inversion algorithm to the analysis of field data acquired near a hydrothermal mine.