• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.4
• /
• pp.281-285
• /
• 2020

Oxide semiconductor devices have become increasingly important because of their high mobility and good uniformity. The channel length of oxide semiconductor thin film transistors (TFTs) also shrinks as the display resolution increases. It is well known that reducing the channel length of a TFT is detrimental to the current saturation because of drain-induced barrier lowering, as well as the movement of the pinch-off point. In an organic light-emitting diode (OLED), the lack of current saturation in the driving TFT creates a major problem in the control of OLED current. To obtain improved current saturation in short channels, we fabricated indium gallium zinc oxide (IGZO) TFTs with single gate and double gate structures, and evaluated the electrical characteristics of both devices. For the double gate structure, we connected the bottom gate electrode to the source electrode, so that the electric potential of the bottom gate was fixed to that of the source. We denote the double gate structure with the bottom gate fixed at the source potential as the BGFP (bottom gate with fixed potential) structure. For the BGFP TFT, the current saturation, as determined by the output characteristics, is better than that of the conventional single gate TFT. This is because the change in the source side potential barrier by the drain field has been suppressed.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.31B no.11
• /
• pp.53-62
• /
• 1994

This paper presents a new approach of analyzing errors resulting from nonideal general-purpose lighting environment when the Photometric Stereo Method (PSM) is applied to estimate the surface-orientation of a three-dimensional object. The approach introduces the explicit modeling of the lighting environment including a circular-disk type irradiance object plane and the direct simulation of the error distribution with the model. The light source is modeled as a point source that has a certain amount of beam angle, and the luminance distribution on the irradiance plane is modeled as a Gaussian function with different deviation values. A simulation algorithm is devised to estimate the light source orientation computing the average luminance intensities obtained from the irradiance object planes positioned in three different orientations. The effect of the nonideal lighting model is directly reflected in such simulation, because of the analogy between the PSM and the proposed algorithm. With an instrumental tool designed to provide arbitrary orientations of the object plane at the origin of the coordinate system, experiment can be performed in a systematic way for the error analysis and compensation. Simulations are performed to find out the error distribution by widely varying the light model and the orientation set of the object plane. The simulation results are compared with those of the experiment performed in the same way as the simulation. It is confirmed from the experiment that a fair amount of errors is due to the erroneous effect of the general-purpose lighting environment.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.8
• /
• pp.1270-1281
• /
• 1989

This paper presents two new storage schemes of 3-D objects to accelerate the finding of the first intersecting object and the shadow computation steps in ray tracing. The 3-D objects which are potentially intersected with the first reflection (refraction)ray are enrolled within a so called reflection (refraction) frustum' for a polygon object. Only those objects registered in the corres ponding frustum are immediately checked for intersection with the secondary rays emanating from the same polygon. The other is called a shadow pyramid' which contains the candidate objects possibly blocking the path from the relevant light source to any point on the relevant polgon. The shadow testing of a point is performed only against the objects contained in the associated shadow pyramid. Despite the cost needed for registration of objects within frusta or shadow pyramids, the total rendering time of ray tracing using the proposed approaches was reduced by approximately 50% (10% in color rendering time and 70% in shadoe testing time) from the conventional cell 50% (10% in color rendering time and 70% in shadow testing time) from the conventional cell traversal scheme under the 3-D uniform subdivision environment due to the fast finding of candidate objects for intersection and the reduced number of intersection calculations.

• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.637-641
• /
• 2007

Airborne LIDAR (Light Detection and Ranging) technology has reached a degree of the required accuracy in mapping professions, and advanced LIDAR systems are becoming increasingly common in the various fields of application. LiDAR data constitute an excellent source of information for reconstructing the Earth's surface due to capability of rapid and dense 3D spatial data acquisition with high accuracy. However, organizing the LIDAR data and extracting information from the data are difficult tasks because LIDAR data are composed of randomly distributed point clouds and do not provide sufficient semantic information. The main reason for this difficulty in processing LIDAR data is that the data provide only irregularly spaced point coordinates without topological and relational information among the points. This study introduces an efficient and robust method for automatic extraction of building footprints using airborne LIDAR data. The proposed method separates ground and non-ground data based on the histogram analysis and then rearranges the building boundary points using convex hull algorithm to extract building footprints. The method was implemented to LIDAR data of the heavily built-up area. Experimental results showed the feasibility and efficiency of the proposed method for automatic producing building layers of the large scale digital maps and 3D building reconstruction.

• Journal of the Korea Safety Management & Science
• /
• v.17 no.3
• /
• pp.355-362
• /
• 2015

There has been an increase of using Bosch Process to fabricate MEMS Device, TSV, Power chip for straight etching profile. Essentially, the interest of TSV technology is rapidly floated, accordingly the demand of Bosch Process is able to hold the prominent position for straight etching of Si or another wafers. Recently, the process to prevent under etching or over etching using EPD equipment is widely used for improvement of mechanical, electrical properties of devices. As an EPD device, the OES is widely used to find accurate end point of etching. However, it is difficult to maintain the light source from view port of chamber because of contamination caused by ion conflict and byproducts in the chamber. In this study, we adapted the SPOES to avoid lose of signal and detect less open ratio under 1 %. We use 12inch Si wafer and execute the through etching 500um of thickness. Furthermore, to get the clear EPD data, we developed an algorithm to only receive the etching part without deposition part. The results showed possible to find End Point of under 1 % of open ratio etching process.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.265-267
• /
• 2001

In this paper, some optical parameters which have effects on the measuring precision and sensitivity of optical current sensor are analyzed. Each parameter occurs changes of specific characteristics of optical sensor system. The influences of performance and characteristics variation of optical current sensor are described in accordance with the changes of optical output power, optical bias point which is called phase difference, and a specific constant related to sensor material and wavelength of light source.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.295-299
• /
• 2007

This paper presents the photovoltaic(PV) water pumping system with a maximum power point tracking(MPPT). The wale- pumping system uses a variable speed single phase induction motor(SPIM) driven a centrifugal pimp by field oriented control(FOC) inverter. The MPPT using a DC-DC converter controlled the duty cycle to track maximum power from PV under different insolation conditions. The duty cycle directly relate with a flux producing current control($i_{ds}$). The FOC inverter uses a current control voltage source inverter(CC-VSI). The simulation results are shown that the characteristics and performance of drive system, which varies as each conditions of light by expresses in voltage ($V_{dq}$), current($I_{dq}$), speed of motor and torque.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1991.04a
• /
• pp.41-45
• /
• 1991

구조 진동에 의해 발생하는 Relative Sound Power를 계산하는 문제가 최근 에 중요시되고 있다. 이 논문에서는 조화적인 집중하중에 대한 무한 탄성보 에서 방출하는 Relative Sound Power를 연구한다. Sound Power는 수치적으 로 적분되고 몇가지 인자들의 함수로써 적분인자를 표시하였다. Keitie와 Peng[2]는 진동하는 보로부터의 방출하는 Relative Sound Power에 대한 하 중 길이의 효과, 그리고 water 하중을 받는 보에서 방출하는 Acoustic radiation에 대한 Source 운동과 기초 강성의 효과를 연구하였다. 보의 진동 응답에서 light fluid loading과 heavy fluid loading에 의한 양쪽의 반응을 고 려한다. 보에는 기초 강성과 Damping 그리고 장력이 작용한다. water 하중 과 air 하중을 받는 보에서 Damping의 변화에 대한 보로부터 방출하는 relative sound power의 크기를 결정하였다. 일반적으로 인장력보다 압축력 이 작용할 때 relative sound power level이 크다는 것을 알고 있다. 실제로 인장력이나 압축력이 보에 작용할 때 relative sound power에 얼마나 영향을 미치는가를 계산하였다. 그리고 진동계로부터 방출하는 sound fluid loading 과 기초 강성에 기인한 복잡한 효과를 해석하였다. 이 논문의 목적은 강성계 수와 wavenumber 비, 그리고 fluid loading에 대한 sound power의 응답에 대하여 설명하고자 한다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.6
• /
• pp.1259-1265
• /
• 1997

We investigate depth measurement error of a range finder based on triangulation method. Geometric analysis resulted in intuitive understanding of the error sensitivity. We show that the depth error is propostional to the distance between the object andthe camera. The measurement value has the highest accuracy when the line connecting the focal point of the camera and the object is perpendicular to the line joining the object and the light source of herange finder. Also we analyze the error using a perturbation method and verify that the results are identical through an experiment.

• Korean Journal of Optics and Photonics
• /
• v.27 no.1
• /
• pp.41-46
• /
• 2016

An optical method to measure the three-dimensional (3D) shape of a surface with specular reflection is proposed. The proposed method is based on the analysis of the geometric path of the light from a point source, and the relative displacements of points in the reflection image. The 3D shape of a concave mirror is shown to be determined approximately via experiments, where the vision system consists of LED array illumination, a half-mirror, and an imaging sensor.