• 조명전기설비학회논문지
• /
• 제25권12호
• /
• pp.54-59
• /
• 2011

LED lightings typically do not fail catastrophically during use. However, over time the light output will gradually depreciate. Even if there are same LED lighting, they are so different at all. because of dissimilar the use and environment of each LED lighting. In this paper, we make a description of reliability analysis procedures for the degradation data using collected field data. Reliability analysis procedures are consisted of estimating degradation models and failure time, verification of distribution and parameters of the distribution, and reliability measures estimation. At some point in time, the light emitted from an LED lightings depreciates to a level where it is no longer considered adequate for a specific application.

• 조명전기설비학회논문지
• /
• 제27권12호
• /
• pp.1-9
• /
• 2013

A standalone LED lighting system in using solar energy has been used usually less than 70W of lighting power because of a troublesome installation and maintenance. In this system, as more and more LED lighting power increases, the capacity of photovoltaic panel does proportionally, and to improve the charging efficiency of solar energy, MPPT(Maximum Power Point Tracking) techniques is used frequently, but the solar tracker is not. In this paper, a solar tracker which traces the light of the sun in varying hour to hour is studied to apply to the standalone LED lighting system. This solar tracker consists of twin axis for tracing the azimuth and altitude respectively, and it has a robust structure with safe mode to stand a strong wind. As a result of analysis, generating efficiency of the traced type has improved on the fixed one 28.84% on average.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(2)
• /
• pp.851-854
• /
• 2004

This paper studies Optical Fiber(OF) - LED illuminated display board system for energy saving. The OF-LED illuminated display board system has PV modules, batteries, and charge & discharge system, and dynamic full color display controller. Both maximum power point tracker (MPPT) and constant current & constant current controls (CCVC) are used In govern the charging system. It can be improve the charging efficiency of battery. The objective of this thesis paper is to build advertisement lighting system with OF-LED in to charge a 12-volts lead acid battery by using a field wired PV array. We saved the maintenance cost and developed of advertisement effectiveness. To verify the proposed OF-LED illuminated display board system for energy saving, the detail simulation and experiment results indicate that operating characteristics are verified by experiment with a laboratory prototype in this paper.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2011년도 춘계학술발표대회 논문집
• /
• pp.168-173
• /
• 2011

Recently, from a saving energy and environmental lighting sources point of view, using LED lighting have been increased rapidly. The colors of light was applied to the control of dimmers that is composed of red, green, blue, and white(RGBW) to improve the quality of visual environment. Moreover this study has been processed to develop adjustable dynamic LED lighting system on SPD and definitize the various spectral power distribution and color temperature of light through the control of the four dimmers. It is possible to combine up to $432^4$ kinds of light. Measurement of illuminance of range on working surface was as 7~l,831 lux. Application of visual environment for occupants can be expected according to control of lighting performance.

• 조명전기설비학회논문지
• /
• 제25권6호
• /
• pp.18-27
• /
• 2011

LED lighting because of high efficiency, long life, friendly environment, as a general lighting of the next generation, has been substituted for incandescent bulb and fluorescent lamp. The proposed system for use of solar battery is the intelligent controller for LED street lights which is improved the method of battery charging and charging efficiency in winter to extend battery life cycle, controlled lighting current according to SoC and in steps. Also, it is implemented emotional lighting which is controlled with the surrounding environment, by using colorful sub LED to take up 10[%] of a source of total light, white LED. As a lab results, the proposed system was implemented functions to adapt to the environmental changes, and improved the charging efficiency and battery life cycle.

• 전력전자학회논문지
• /
• 제19권4호
• /
• pp.297-302
• /
• 2014

In this paper, a LED driver compatible with TRIAC-dimmer applying active bleeder is proposed. If TRIAC-dimmer is connected with LED driver, flicker phenomenon occurs by TRIAC malfunction. In order to prevent this problem, a current over holding current must flow into TRIAC. Therefore, additional circuit compatible with TRIAC-dimmer is required to provide enough current. Passive bleeder has power loss in whole operation period. The proposed circuit apply a valley-fill circuit for power-factor-correction and a novel active bleeder detecting malfunction point of TRIAC. Therefore, it prevent malfunction of TRIAC-dimmer and have advantage of higher efficiency than passive bleeder. To verify the validity of proposed circuit, 13W-lighting LED driver prototype has been proposed.

• 전자공학회논문지SC
• /
• 제46권5호
• /
• pp.15-21
• /
• 2009

LED와 같은 소형 제품의 불량검색은 제품의 질을 향상 시키는 것만 아니라 생산성 향상에서 중요한 역할을 한다. 본 연구에서는 LED에 발생하는 여러 가지 불량을 자동으로 검사하는 시스템을 구성하였다. LABVIEW Builder를 사용하여 그래픽 인터페이스 상에서 LED의 불량을 검출을 자동판단하며, 사용자가 쉽게 사용 가능하도록 설계하였다. 1394 카메라를 통해 영상을 획득하고 Vision Builder의 각 영상처리 요소를 적용하였다. 에지탐색, 기하학 위치 설정, 거리측정 등의 영상처리 알고리즘을 조합하여 색과 크기가 다른 다양한 LED의 불량을 검출하는 알고리즘을 설계하였다.

• 한국전자통신학회논문지
• /
• 제10권5호
• /
• pp.615-622
• /
• 2015

반도체 제조기술의 발달로 고효율 및 고휘도의 LED가 개발됨에 따라 재래식 조명들로부터 LED를 이용한 조명으로 조명산업이 이동하는 추세이다. LED 조명등은 에너지 효율이 재래식 조명보다 뛰어나지만 많은 열이 발생한다는 단점이 있다. 특히 대형 LED 조명등에서는 이러한 발열문제가 심각한 실정으로, LED에 의한 메탈기판의 열은 납땜 부분을 열화시켜 조명등의 수명을 단축시키는 주된 원인이 된다. 따라서 대형 조명등을 개발하기 위해서는 이러한 열 문제를 해결하는 것이 매우 중요하다. 본 연구에서는 대형 LED 조명등에서 열문제를 해결하기 위한 방법을 제시하였고, 제시한 방식으로 1200W급 LED 조명등을 개발하였다. 본 연구에서 이용한 방법은 LED 조명등에 워터재킷을 설치하여 냉각수를 채웠으며, 소형의 수중펌프를 이용하여 냉각수를 순환시키는 방법을 이용하였다.

• 한국전기전자재료학회논문지
• /
• 제29권11호
• /
• pp.729-735
• /
• 2016

It is highly important issue to use an energy efficiently for sustainable prosperity of mankind. From this point of view, using LED lighting can be a good alternative because it has a lot of advantages such as high efficiency, long life time and eco-friendly manufacturing process. That is the reason why using LED lighting has been encouraged worldwide. However, in situations that LED lighting is replacing traditional lighting quickly, the problem of the flicker of LED lighting has emerged as an important issue. Therefore, in foreign countries like US or Japan in order to ensure the reliability of LED lighting, study for flickering effects of the human body and test methods are have been actively conducted. But related research in domestic situation is an insufficient condition. In this study, a flicker characteristic was measured conventional lamps such as incandescent lamps or fluorescent lamp and 81 items of LED lightings which are distributed in domestic markets.

• 조명전기설비학회논문지
• /
• 제21권6호
• /
• pp.26-32
• /
• 2007

기존의 LED 광학계의 설계법은 크게 점광원 가정법과 가초점 설계법이 있으나, 이 설계법들은 LED와 광학계간의 거리가 매우 좁아지게 될 경우 큰 오차가 발생하는 단점이 존재하였다. 본 논문에서는 LED를 등간격으로 분할하여 각부분의 배광을 예측하고, 광선의 역추적 기법을 활용하여 이에 대한 결과를 확인한 후 분할된 각 구간에 대하여 세그먼트의 개별적인 설계를 통하여 오차를 감소시키는 새로운 설계법을 제시한다. 설계법의 설명이후에 2종의 예시 광학계를 설계하고 광학 성능 예측 프로그램을 통하여 배광과 광학 효율을 평가하였다.