• 대한기계학회논문집B
• /
• 제22권4호
• /
• pp.450-467
• /
• 1998

The characteristics of the unstable impinging circular jet is investigated based on the frequency characteristics and the sound field of the impinging-tones. Two symmetric modes S1 and S2, associated with low frequency and high frequency respectively, and one helical mode H have been observed. At low speed the S2 mode is dominant and switched by the S1 mode as the speed increases. When the jet speed is high the S1 mode is very active over the impinging distance from half the nozzle diameter to its ten times, while the S2 mode occurs at shorter distance corresponding to stage 2 and 3. The helical mode H seems unstable, likely to be influenced much by the experimental environment, and occurs at relatively high speed with almost the same frequency characteristics as the S2 mode. By estimating the convection speed of the unstable jet, it is found that the ratio of the convection speed to the jet speed decreases with both Strouhal number and Reynolds number and the speed of S2 mode is faster than the Si mode. When the present experimental results are compared with the previous investigations performed for the hole tone and the impinging tone with a small plate, the S1 mode is found to be associated with the ring vortex of large diameter with low speed, but the S2 mode with the vortex of small diameter with high speed. In addition, the frequency is found to be influenced by the nozzle configuration but the characteristics is almost the same. From the impinging distance and frequency range, it can be deduced that S1 mode is related with the jet column mode and S2 mode with the shear mode.

• Journal of Microbiology and Biotechnology
• /
• 제15권1호
• /
• pp.155-160
• /
• 2005

Abstract A direct approach was used to retrieve active lipases from Paenibacillus polymyxa genome databases. Twelve putative lipase genes were tested using a typical lipase sequence rule built on the basis of a consensus sequence of a catalytic triad and oxyanion hole. Among them, six genes satisfied the sequence rule and had similarity (about 25%) with known bacterial lipases. To obtain the six lipase proteins, lipase genes were expressed in E. coli cells and lipolytic activities were measured by using tributyrin plate and pnitrophenyl caproate. One of them, contig 160-26, was expressed as a soluble and active form in E. coli cell. After purifying on Ni-NTA column, its detailed biochemical properties were characterized. It had a maximum hydrolytic activity at $30^{\circ}C$ and pH 7- 8, and was stable up to $40^{\circ}C$ and in the range of pH 5- 8. It most rapidly hydrolyzed pNPC$_6$ among various PNPesters. The other contigs were expressed more or less as soluble forms, although no lipolytic activities were detected. As they have many conserved regions with lipase 160-26 as well as other bacterial lipases throughout their equence, they are suggested as true lipase genes.

• 한국운동역학회지
• /
• 제20권2호
• /
• pp.239-243
• /
• 2010

The putting stroke accounts for 40~50% of total stroke for a golf rounding and most golfers have difficulties on the puting. Studies for the putting stroke have been conducted by analyzing various factors such as kinematics, kinetics, psychologic and physiologic parameters. A lot of devices were developed to support the studies. However there was no appropriate method to measure the position of the ball quantitatively. In this study, we developed a new measurement system to measure and evaluate the putting result. The developed system uses a USB camera to take the 2-dimensional image of the surface including the hole cup at the center of the image and the ball. The position of the ball is extracted as a set of distance and angle in polar coordinate system. We evaluated the new system with an indoor set-up for putting experiments and the system provided accurate measurement results. The proposed system can be combined with the other measurement systems such as 3D motion capture system and force plate without any restriction.

• 대한기계학회논문집A
• /
• 제20권11호
• /
• pp.3516-3524
• /
• 1996

Service conditions for structures at elevated temperatures in nuclear power plant involve transient thermal and mechanical load levels that are severe enough to caeuse inelastic deformations due to creep and plasticity. Therefore, a systematic mehtod of inelastic analysis is needed for the design of structural components in nuclear poser plants subjected to such loading conditions. In the present investigation, the Chabodhe model, one of the unified viscoplastic constitutive equations, was selected for systematic inelastic analysis. The material response was integrated based on GMR ( generallized mid-point rule) time integral scheme and provided to ABAQUS as a material subroutine, UMAT program. By comparing results obtaned from uniaxial analysis using the developed UMAT program with those from Runge-Kutta solutions and experimentaiton, the validity of the adopted Chaboche model and the numerical stability and accuracy of the developed UMAT program were verified. In addition, the developed material subroutine was applied for uniaxial creep and tension analyses for the plate with a hole in the center. The application further demonstrates usefulness of the developed program.

• Smart Structures and Systems
• /
• 제28권6호
• /
• pp.745-760
• /
• 2021

Dynamic buckling of structure is one of the failure modes that needs to be considered since it may result in catastrophic failure of the structure in a short period of time. For a thin fiber-reinforced polymer (FRP) plate under compression, buckling is an inherent hazard which will be intensified by the existence of defects like holes, cracks, and delamination. On the other hand, the growth of the delamination is another prime concern for thin FRP plates. In the current paper, reinforcing the plates against buckling is realized by using SMA wires in the form of stitches. A numerical framework is proposed to simulate the dynamic instability emphasizing the effect of the SMA stitches in suppressing delamination growth. The suggested algorithm is more accurate than the other methods when considering the transformation point of the SMA wires and the modeling of the cohesive zone using simple and yet reliable technique. The computational design of the method by producing the line by line orders leads to a simple algorithm for simulating the super-elastic behavior. The Lagoudas constitutive model of the SMA material is implemented in the form of user material subroutines (VUMAT). The normal bilinear spring model is used to reproduce the cohesive zone behavior. The nonlinear finite element formulation is programmed into FORTRAN using the Newmark-beta numerical time-integration approach. The obtained results are compared with the results obtained by the finite element method using ABAQUS/Explicit solver. The obtained results by the proposed algorithm and those by ABAQUS are in good agreement.

• Composites Research
• /
• 제21권4호
• /
• pp.15-21
• /
• 2008

단일 탄소섬유에 부착된 반구형 미소본드 시험편을 제사하여 에폭시수지와 난소섬유사이의 계면전단강도를 평가하였다. 반구형 미소시험편의 경우, 드랍레트 미소접합시험편 및 역반구형 미소접합시험편과 비교하여 계면강도측정값들이 높은 회귀계수 및 삭은 편차를 보여주었다. 이는반구형 시험편의 메니스커스 부분이 다른 미소시험편보다 작으며 핀홀 부하장치의 선단과 접촉하고 있는 수지부분에서 응력집중이 감소했기 때인 것으로 사료된다. 이들 시험에 대한 유한요소해석결과, 반구형시험편에서는 수지/섬유의 계면부를 따라 전단응력분포가 응력모드의 전환이 없이 안정하였다. 또한 이들 계면강도 측정데이터는 미소 바이스의 선단과 핀홀 판의 선단과 같은 부하장치의 종류에 따라 달라졌음을 알았다.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제31권2호
• /
• pp.127-135
• /
• 2009

Objectives : The titanium fixation system has been used in orthognathic surgery for fixation of bone segments usually, but the biodegradable fixation system was developed and also being used. The strongest point in the biodegradable system is that no extra operation should be needed to remove fixation materials. In spite of this merit, oral & maxillofacial surgeons hesitate to use this system in fracture or orthognathic surgery. In this study, as we got some clinical experiences, we'd like to report the result of clinical study using the biodegradable fixation system in orthognathic surgery. Patients and Methods : A total of 35 patients composed of 17 males and 18 females with 25 osteotomies in maxilla and 34 osteotomies in mandible were fixated with the biodegradable fixation system(Inion $CPS^{(R)}$). We investigated methods of stabilization, fixation time, and complications on the basis of the method as above. Results : Four 2mm thick L shaped plates with 7 holes of which 1 hole was removed were fixed in maxilla with six $2.0{\times}7mm$ screws. Three $2.5{\times}16{\sim}18mm$ screws were used to fix superior ramus area and one mandibular angle area in mandible. It took about 27.4 minutes in maxilla, 25.3 minutes in mandible to perform the fixation which took longer time than the titanium system(9.5 minutes in maxilla, 8 minutes in mandible). Generally, there was no problem except 9 cases in which there were some complications. Conclusions : In most cases, the biodegradable fixation system can be used without problem in usual orthognathic surgery. But, this system is inferior to the titanium fixation one in some respects such as fixation time, size, and physical property. Some supplementations for such weak points as aforementioned should be needed for the universal use of biodegradable materials.

• 대한핵의학회지
• /
• 제38권1호
• /
• pp.74-84
• /
• 2004

목적:. I-125는 저에너지(27-35 keV) 방사선을 방출하기 때문에 두께가 얇은 섬광결정과 조준기를 사용할 수 있어 고분해능, 고민감도 영상획득에 유리한 물리적 특성을 가지고 있다. 이 연구의 목적은 새로운 시뮬레이션 도구인 GATE (Geant4 Application for Tomographic Emission)를 사용하여 최적의 I-125 SPECT 시스템 파라미터를 도출하는 것이다. 대상 및 방법: 시뮬레이션 방법의 신뢰성을 검증하기 위해, Weisenberger 등이 개발한 감마 카메라 시스템을 모사하였다. 섬광체로 평판형 Nal(T1)을 사용하였으며, 두께는 검출효율을 계산해서 결정하였다. 평행구멍조준기와 바늘구멍조준기의 여러 파라미터가 공간분해능과 민감도에 미치는 영향을 평가하였다. 그리고 최적화된 조준기를 결합한 I-125 SPECT의 성능을 평가하였다. 결과: 시뮬레이션에 대한 신뢰성 검증연구 결과, 측정과 시뮬레이션에서 공간분해능(4%)과 민감도(3%)가 유사함을 확인하였다. Nal(T1) 두께는 I-125 감마선을 98% 검출할 수 있도록 1 mm로 결정하였다. 시뮬레이션 결과 고분해능 평행구멍조준기로 구멍크기가 0.2 mm이고 길이가 5 mm인 사각구멍조준기를 선택하였고, 범용 평행구멍조준기로 구멍크기가 0.5 m이고, 길이가 10 mm인 육각구멍조준기를 선택하였다. 바늘구멍조준기는 구멍지름이 0.25 mm이고 채널높이가 0.1 mm이며, 허용각도가 90도인 조준기를 선택하였다. 최적화된 고분해능 평행구멍조준기, 범용 평행구멍조준기, 바늘구멍조준기를 결합한 I-125 SPECT의 재구성 영상 공간분해능은 각각 1.2 mm, 1.7 mm, 0.8 mm였으며, 민감도는 39.7 cps/MBq, 71.9 cps/MBq, 5.5 cps/MBq이었다. 결론: GATE 시뮬레이션으로 I-125 영상에 적합한 섬광결정 파라미터 및 조준기 파라미터를 도출하였다. 이 연구결과는 I-125 SPECT로 탁월한 고분해능, 고민감도 영상을 얻을 수 있음을 보여준다.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 춘계학술대회 초록집
• /
• pp.172.2-172.2
• /
• 2010

This study was carried out in order to reduce the installation expense of heating system for greenhouse comparing to geothermal heat pump and develope the coefficient of performance (COP) for a heat pump. For getting plenty of heat flux from geothermal energy. Surface water in river channel was used for getting a lots of geothermal heat by penetrating water through underground soil layer of the river bank that make heat transmission to passing water. The range of water temperature after the process of Ground filtration is 13~18 degrees celsius which is very similar to low heat source of geothermal heat pump system and the plenty amount of heat source from that make the number of geothermal heat exchanging hole and the expense for geothermal heat exchanger construction reduced. Drainage well is also used for returning filtration water to the aquifer that keep the water good recirculation from losing geothermal heat and water resource. For the COP improvement of Heat pump, thermal storage tank with separating insulation plate according to the temperature difference make the COP of Heat pump that is similar to thermal storage tank with diffuser. Developed thermal storage tank make construction expense cheaper than customarily used one's. and that sand filter and oxidation sand (FELOX) are going to be used for improving ground filtration water quality that make heat exchanger efficiency better. All above developed component skill are going to be set on the Ground filtration water source heat pump system and applied for medium, large scale for protected greenhouse in riverside area and on-site experiment is going to do for optimizing the heating system function and overcome the problem happening in the process of on-site application afterward.

• 한국안전학회지
• /
• 제5권1호
• /
• pp.19-29
• /
• 1990

The objective of this paper is to investigate the effect of residual stresses on the $\Delta$K$\sub$th/ and fatigue crack growth behavior of butt weldments. For this purpose, transverse butt sutmerged arc welding was performed on SM50A steel plate and CT(compact tension) specimens which loading direction is perpendicular to weld bead were selected. Welding residual stresses distribution on the specimen was determined by hole drilling method. The case of crack located parallel to weld bead, the states of as weld and PWHT, $\Delta$K$\sub$th/ of specimens(HAZ, weld zone) was higher than that of the base metal probably because of the compressive residual stresses of crack tip. In low $\Delta$K region, it is estimated that the effects of residual stresses for da/dN are great. In region II, the da/dN of weldments in as weld state was lower than that of the base metal. Though da/dN of Weldments in PWHT state was similar to that of the base metal. The constant of power law, m in two states consisted with the base metal. Therefore , it is estimated that the value of m is not affected by residual stresses. Fatigue crack growth behavior of weldments consisted with the base metal considering the effective stress intensity factor range($\Delta$K$\sub$eff/) included the effect of initial residual stress(Kres). Thus, we can predict the fatigue crack growth behavior of weldment by knowing the distribution of initial residual stress at the crack tip.