• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제30권6호
• /
• pp.513-517
• /
• 2008

Purpose: This study aimed to evaluate distribution and maximal value of mechanical stresses on the reconstruction plate, bridging mandibular symphysis defect, and to optimize the most appropriate locations of the plate to distribute the stress causing the fracture of the plate. Materials and methods: Four types of reconstruction were constructed by different number and location of the reconstruction plates on the 3 D finite element model (FEM) of a human edentulous mandible; Type I: one plate on the inferior border of the anterior mandible, Type II: one plate on the middle of the anterior mandible, Type III: one plate on the superior border of the anterior mandible, and Type IV: two plates on the inferior and superior border of the anterior mandible. Results: The results showed that the maximal stress of type I (234.29 Mpa) was lower than that of type II (260.91 Mpa) and type III (247.37 Mpa), but higher than that of type IV (186.64 Mpa). We could also observe that the stresses are tending to focus on the inner side and inferior part of the plate which connected proximal segment from the vertical load. Conclusions: On the basis of the findings, it was concluded that using a plate on the inferior border of mandible or two plates on the inferior and superior border of mandible are more favorable to distribute mechanical stresses, which could reduce the fracture of the plate.

• 한국생산제조학회지
• /
• 제25권1호
• /
• pp.89-95
• /
• 2016

This study investigated the design factors of the opening area in order to consider the kinematic stability of a valve plate, conducting an analysis of the reduction effects of pressure pulsation and flow ripple depending on the design factors, using the $SimulationX^{(R)}$ (Germany) hydraulic analysis program. Further, we performed a structure analysis to confirm the kinematic stability of the valve plate in a swash plate type piston pump, and analyzed the effects of pulsation on a 1-step V-type notch, 2-step V-type notch, and 2-step U-type notch to determine the effects of pulsation reduction. Finally, we show the effectiveness of our proposed design of the pre-compression sections on a valve plate in terms of low pulsation by using the hydraulic analysis program, $SimulationX^{(R)}$.

• 설비공학논문집
• /
• 제24권8호
• /
• pp.636-645
• /
• 2012

The performance of various type plate exchangers with different chevron angle, dimple size and arrangement was analysed by using Ansys v13.0. Heat transfer performance, pressure drop and flow patten of plate heat exchanger were investigated according to mass flow ratio investigated and compared. As a result, the $60^{\circ}$-chevron type plate heat exchanger showed the highest heat transfer performance but pressure drop was relatively high. The efficiency of $45^{\circ}$-chevron type plate heat exchanger showed the best performance in considering of heat transfer performance and pressure drop simultaneously. Among dimple type plate heat exchangers, the highest heat transfer performance was shown in a dim_zigzag type plate heat exchanger but pressure drop was very high. Besides, the dim_upsize plate heat exchanger showed very low pressure drop.

• 소성∙가공
• /
• 제20권4호
• /
• pp.273-278
• /
• 2011

Employing the TRIZ problem solving technique, a hybrid-type center plate for the molten carbonate fuel cell(MCFC) was developed for the purpose of improving gas sealing and maintenance. The manufacturing method of the hybrid-type center plate was divided into a trimming operation and a two-step bending process. In the latter, a modified punch shape was used to reduce springback. Using finite element(FE) simulations, bending stresses in the thickness and the in-plane directions were computed and the bending conditions were optimized. The optimized results of the two-step bending process were used as a basis for the design of the trimming process of the hybrid-type center plate. Finally, the external manifold-type center plate and the hybrid-type center plate were fabricated using a die set that accounts for the optimized conditions. It was found that the numerical simulation results were in good agreement with the experiments.

• 한국인쇄학회지
• /
• 제15권2호
• /
• pp.77-90
• /
• 1997

Positive type presensitized offset plate developer were blended by quantitative analysis method. The test had been proceeeded to check variation of developability, shelf life and tone reproduction by SiO2/Na2O ratio to PS plate developer, added glycerin, and sodium phosphate with glycerin. This study of tone reproduction had been tested 5 times to get accuracy by PS platesusing kodak CCG C-3, KMS. The test result of tone reproduction of presensitized offset plates can be summarized as follows ; major compositions in positive type plate developer were Na, Si, K and P, developability were increased by Sio2/NaO2 ratio in positive type plate developer. Shelf life can be kept by add glycerin to positive type plate developer. Tone reproduction were improved by sodium phosphate due to buffer action while shelf life can be kept by add glycerin in positive type plate developer.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.621-625
• /
• 1997

Recently, wash plate type hydraulic axial piston motors are being in extensively used in the world, because of simple design, lightweight, effective cost. But the structural problem of swash plate type hydraulic axial piston motor is the limited angle of swash plate and lateral force having a undesirable effect in piston. To solve these problems. a connecting rod mechanism. which is commonly used in hent axis type motors, is considered to be applied the swash plate cype motor. In this paper, kinematic analysis is done on the connecting rod mechanism. A series of formula are derived and numerical calculations are done for a set of motor parameters.

• 한국생산제조학회지
• /
• 제24권2호
• /
• pp.244-250
• /
• 2015

We propose a simulation technique to estimate the reduction effect of the pressure/flow pulsation by analysis of the pulsation variables and notch shape of the valve plate of a swash-plate-type variable piston pump. First, using SimulationX$^{(R)}$, we perform a theoretical kinematic analysis according to the variable swash-plate angle and rotational velocity in order to design a single-piston pump. In designing the notch shape of the valve plate of the swash-plate-type variable piston pump as one of the pulsation variables, we investigate the effect of the pulsation by comparing two notch types (circular type and V type). Then, we extend our analysis to a nine-piston pump model. This paper not only confirms the effect of the pressure/flow pulsation according to pulsation variables but can also be applied to the development of a SimulationX$^{(R)}$-based simulation technique for notch-shape optimization for a swash-plate-type variable piston pump.

• 대한조선학회지
• /
• 제7권2호
• /
• pp.27-40
• /
• 1970

The distribution of stress and strain in elastic stages is investigated by the experiments of two dimensional photoelastic coating and Moire fringe method. Center block type and cover plate type of fillet welds are used as specimens in the test. The results are as follows. 1) Center block type gets less uniform stress distribution than cover plate type. And its stress concentration factor, especially at root, is larger than that at toe. 2) When main plate and cover plate closely contact and it cause friction, stress concentration decreases more than that in case of slit. That is because stress can be transmitted on the contact surface. 3) When slit is made, the outside of fillet gets more stress than the inside of it. 4) While the plastic strain distribution of center block type reaches the maximum at root and differs very slightly from that under lower loading, the plastic strain distribution of cover plate type is inclined to get the maximum at the outside of fillet rather than at root. 5) When the plastic strain value of cover plate type is compared with that of center block type at toe and root, the relations between the former and the latter shows root<toe and root>toe. 6) Because stress distribution becomes changed according to loading, fracture angle cannot be estimated by the peaks of elastic stress distribution. 7) The strain distribution just before fracture can be found by Moire fringe method.

• 전기학회논문지
• /
• 제64권7호
• /
• pp.1012-1018
• /
• 2015

The studies on the operating performance analysis or design about the fixed tilt angle flat-plate photovoltaic (PV) system are still lively going off. However the operating property analysis about the arch type PV system which means PV array were designed as round type is dissatisfied. In this paper, we theoretically established the factors which are cause of the deterioration in performance of arch type PV system. In addition, we use the Solar Pro simulation tools to design both flat-plate type and arch type 30kW PV systems. The simulations about arch type PV system applied two ways such as central inverter and string inverter were conducted. The performance ratio (PR) of the PV system with flat-plate type shows the highest value 74[%] when the tilt angle is 30°. In case of arch type, when applying central inverter method, PR value shows approximately 73[%] and no more difference with arch type of the PV array. This value shows 1[%] decrease compare with the flat-plate type. However when applying string inverter methods, the average PR value shows 80 % and 6% improved than the central inverter method.

• 한국정밀공학회지
• /
• 제20권6호
• /
• pp.123-129
• /
• 2003

Recently, the life cycle of products is rapidly shortened and then the disposal of the used mold applied in development of the product is a difficult thing. In this study, we proposed the feasibility of new three plate type mold structure for recycling by analyzing of the existing standard mold base. And in order to apply new three plate mold structure in mold design and making. we constructed the specifications for mold parts such as runner stripper plate, cavity plate, core plate and slide core unit. Also, we confirmed the possibility of recycling mold base by testing a used three plate mold for audio front panel.