• Nuclear Engineering and Technology
• /
• v.54 no.9
• /
• pp.3398-3402
• /
• 2022

We fabricated a 15 m long position-sensitive plastic scintillation optical fiber (PSOF) detector consisting of a PSOF, two photomultiplier tubes, four fast amplifiers, and a digitizer. A single PSOF was used as a sensing part to estimate the gamma-ray source position, and ¹³⁷Cs, an uncollimated solid-disk-type radioactive isotope, was used as a gamma-ray emitter. To improve the sensitivity, accuracy, and measurement time of a PSOF detector compared to those of previous studies, the performance of the amplifier was optimized, and the digital signal processing (DSP) was newly designed in this study. Moreover, we could measure very low dose rates of gamma-rays with high sensitivity and accuracy in a very short time using our proposed PSOF detector. The results of this study indicate that it is possible to accurately and quickly locate the position of a very low dose rate gamma-ray source in a wide range of contaminated areas using the proposed position-sensitive PSOF detector.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.15 no.4
• /
• pp.303-316
• /
• 1993

The auricular cartilage grafts have been widely used in replacement of the temporomandibular joint disk. Cartilage grafts itself have a low metabolism and high survival rate after grafting. In processing the grafting materials, it was important to preserve the properties of chondrocyte proper. We used 15% glycerol and 10% DMSO (Dimethyl Sulfoxide) solutions for cartilage fixation before deep freezing. We have performed the allogenic auricular cartilage graft in the temporomandibular joint of 20 rabbits which 10 specimen was treated with 15% glycerol and the other 10 specimen was treated with 10% DMSO respectively and examined in 1, 2, 4, 6 and 8 weeks after operation histopathologically. The result were : 1. Inflammatory cell infiltration around the grafted material appeared more glycerol groups than DMSO groups at 1 week, but each group has no differences after 2 weeks. 2. Degenerative changes of grafted auricular chondrocytes were more deveolped in glycerol group than DMSO groups till 4 weeks, but there were no differences between two groups after 6 weeks. 3. Fibrous union between grafted fragment and mandibular condyle was prominent in DMSO group. 4. Vascular proliferation of the grafted auricualr cartilage was more developed in DMSO groups than glycerol group in early stage. 5. Amount of the additional growth of grafted auricular cartilage was more existed in DMSO groups than glycerol group. 6. General survival rate after grafting was more prominent in DMSO group. In summary, allogenic auricular cartilage grafts treated with 15% glycerol and 10% DMSO solution have supported to survivalbility as a cryopreservative agents, especially DMSO groups have little inflammatory cell infiltration in early stages and degenerative changes and additional growth are more prominent than glycerol groups.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.19 no.3
• /
• pp.287-299
• /
• 1997

Procurement, cutting, cleansing, freezing, freeze-drying, and demineralization of the allogeneic bone must be made under the germ-free stable condition without bacterial and/or viral contamination. Even thought the bone is procured under the germ free condition, we must have confidence on disinfection of all the solutions that come in contact with tissue during the whole procedure. Lots of antibacterial agents have been introduced for chemical sterilization. Recently ethylene oxide gas sterilization or radiation sterilization is frequently selected as a secendary sterilization procedure. The biological and biochemical response of the graft material differs with the type and concentration of the sterilizing agents, and various toxic reactions have been reported due to the graft material itself and the substance released by the chemicals. The authors conducted the Millipore filter test to observe the toxic effect on L929 fibroblasts according to the effect on activity of succinate dehydrogenase, during the secondary sterilization of the demineralized allogeneic bone powder with irradiation or ethylene oxide gas. The result were as follows : 1. Around the copper disk, positive control group, 10mm diameter discoloration was observed. 2. As same as the negative control group, the disk showed no discoloration. 3. The demineralized allogeneic bone which was sterilized with ethylene oxide gas or irradiation showed no cytotoxicity. 4. From this results, it is suggested that treatment with ethylene oxide gas or irradiation should be effective to sterilize the deminineralized allogeneic bone.

• Resources Recycling
• /
• v.23 no.4
• /
• pp.30-36
• /
• 2014

300,000 tons of waste tires are annually being produced with development of the automotive industry in Korea. Landfill and incineration treatment system are causing the economic problem through secondary environmental pollution and waste. Therefore, as one of the ways to take advantage of this, Thermo-Plastic Vulcanized (TPV) composite was prepared by the ground waste tire and plastic powders. The waste tire powder was gained by mechanical fracturing through crushers. The waste tire powder was ground by a shear crushing method and a 2-stage disk mill method instead of cutting crushing one. The waste tire powder of 50 mesh was mixed with Polypropylene(PP) in various proportions. TPVs were prepared by an extrusion, and tensile and impact tests were performed. In addition, the same experiments were repeated in 40, 80, 140 mesh conditions in order to observe size effect of waste tire powders.

• Transactions of the Society of Information Storage Systems
• /
• v.8 no.2
• /
• pp.72-77
• /
• 2012

The demand for the laptop computer has been increased day by day and most of users ask quiet computer and devices to work in comfortable environment. One of the devices which generate acoustic noise is an external ODD. Unlike the internal ODD, the external ODD is easy to emit noise because it runs outside of the computer and also it is packed with a thin plastic covers. As the disk rotates, vortex flow is generated inside of the cavity due to various and complicated mold parts of the cover. In addition, there is a gap between the disk tray and the upper/lower cases, through which the air flows as well as the noise leaks. In this study, we have proposed how to reduce the acoustic noise of an external ODD using numerical and experimental analysis. The pressure fluctuations and turbulent kinetic energy distributions are calculated for the developed model. The results show that the sound pressure level is reduced by 2.3dB through simple modifications of ribs of the top cover, which remove or suppress flow instabilities inside of the cavity.

• Journal of Mechanical Science and Technology
• /
• v.16 no.9
• /
• pp.1065-1071
• /
• 2002

The friction and wear behaviors of magnetron sputtered MoS$_2$ films were investigated through the use of a pin and disk type tester. The experiments were performed for two kinds of specimens (ground (Ra 0.5 $\mu\textrm{m}$) and polished (Ra 0.01 $\mu\textrm{m}$) substrates) under the following operating condifions : linear sliding velocities in the range of 22～66 mm/s (3 types), normal loads varying from 9.8～29.4 N(3 types) and atmospheric conditions of air, medium and high vacuum (3types). Silicon nitride pin was used as the lower specimen and magnetron sputtered MoS$_2$ on bearing steel disk was used as the upper specimen. The results showed that low friction property of the MoS$_2$ films could be identified in high vacuum and the specific wear rate in air was much higher than that in medium and high vacuum due to severe oxidation. It was found that the main wear mechanism in air was oxidation whereas in high vacuum accumulation of plastic flow and adhesion, were the main causes of wear.

• Design & Manufacturing
• /
• v.7 no.1
• /
• pp.28-33
• /
• 2013

During the cold forming, due to high working pressure acting on the die surface, failure mechanics must be considered before die design. One of the main reasons of die failure in industrial application of metal forming technologies is wear. The mechanisms of wear are consisted of adhesion, abrasion, erosion and so on. Die wear affects the tolerances of formed parts, metal flow, and costs of process. The only way to control these failures is to develop a prediction method on die wear suitable in the design state in order to optimize the process. The wear system is used to analyse 'operating variables' and 'system structure'. In this study, with AISI D2, AISI 1020, AISI 304SS materials, a series of the wear experiments of pin-on-disk type to obtain the wear coefficients from Archard's wear model and the upsetting processes are carried out to observe the wear phenomenon during the cold forming process. The analysis of upsetting processes are performed by the rigid-plastic finite element method. The result of the analysis is used to investigate the die wear the processes, and the analysis simulated die wear profiles are compared with the experimental measured die wear profiles.

• Korean Journal of Materials Research
• /
• v.15 no.12
• /
• pp.824-828
• /
• 2005

In this study the effect of the content of $TiB_2$ on wear properties was investigated. $Cu-TiB_2$ composites have been fabricated by hot extrusion. Sliding wear tests were peformed by a pin-on-disk type wear test machine under dry condition and loads varied with from 20N to 80N at sliding speed 3.5Hz. The test results showed that the wear losses and the friction coefficients decreased with increasing $Cu-TiB_2$ volume fraction and increasing the size of $Cu-TiB_2$ particle. Wear property of $10{\mu}m,\;5 vol\%\; TiB_2$ specimen was excellent all of the wear specimens. It is thought that the increase of plastic flow resistivity due to uniform distribution of $10{\mu}m,\;5 vol\%\; TiB_2$ wear specimen would improve wear property. The worn surface and wear debris were examined by optical microscope and scanning electron microscope.

• Journal of Powder Materials
• /
• v.29 no.6
• /
• pp.517-522
• /
• 2022

We investigate the austenite stability in nanocrystalline Fe-7%Mn-X%Mo (X = 0, 1, and 2) alloys fabricated by spark plasma sintering. Mo is known as a ferrite stabilizing element, whereas Mn is an austenite stabilizing element, and many studies have focused on the effect of Mn addition on austenite stability. Herein, the volume fraction of austenite in nanocrystalline Fe-7%Mn alloys with different Mo contents is measured using X-ray diffraction. Using a disk compressive test, austenite in Fe-Mn-Mo alloys is confirmed to transform into strain-induced martensite during plastic deformation by a disk d. The variation in austenite stability in response to the addition of Mo is quantitatively evaluated by comparing the k-parameters of the kinetic equation for the strain-induced martensite transformation.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.34 no.3
• /
• pp.173-179
• /
• 2012

Purpose: This study was to determine the effects of surgical induction of anterior disc displacement (ADD) on the distribution of glycosaminoglycan (GAG) and collagen fiber arrangement in the rabbit temporomandibular joint (TMJ) tissues including articular cartilage of condyle, disc, retrodiscal tissue, and articular eminence. Methods: We used van Gieson staining and Alcian blue critical electrolyte concentration (CEC) method to observe change of collagen fibers on disc and to measure GAG up to 10 weeks in TMJ tissues after surgical induction of ADD on 25 rabbits. Results: CEC measurements for GAG showed 0.3 M, 0.4 M, 0.6 M, and 0.8 M at 1 week, 2 weeks, 3, 4, and 8 weeks, 10 weeks, respectively. This result indicated that GAGs shifted to highly sulphated ones as time passed. Disruption of collagen fiber arrangement in the disk occurred at 10 days and aggravated at 3 weeks. Conclusion: Our study showed degenerative osteoarthritis changes in rabbit TMJ following surgical induction of ADD up to 10-week period.