• Journal of the Korean Vacuum Society
• /
• v.21 no.4
• /
• pp.199-204
• /
• 2012

$SF_6$ gas is widely used for dry etching process of semiconductor and display fabrication process. But $SF_6$ gas is considered for typical greenhouse gas for global warming. So it is necessary to research relating to $SF_6$ alternatives reducing greenhouse effect in semiconductor and display. $C_3F_6$ gas is one of the promising candidates for it. We studied about etch characteristics by performing Reactive Ion Etching process of dry etching and reduced gas element exhausted on etching process using absorbent Zeolite 5A. $Si_3N_4$ thin film was deposited to 500 nm with Plasma Enhanced Chemical Vapor Deposition and we performed Reactive Ion Etching process after patterning through photolithography process. It was observed that the etch rate and the etched surface of $Si_3N_4$ thin film with Scanning Electron Microscope pictures. And we measured and compared the exhausted gas before and after the absorbent using Gas Chromatograph-Mass Spectrophotometry.

• Korean Journal of Materials Research
• /
• v.10 no.6
• /
• pp.450-455
• /
• 2000

For further scaling down of the silicon devices, the application of low dielectric constant materials instead of silicon oxide has been considered to reduce power consumption, crosstalk, and interconnection delay. In this paper, the effect of $O_2/SF_6$ plasma chemistry on the etching characteristics of polyimide-one of the promising low-k interlayer dielectrics-has been studied. The etch rate of polyimide decreases with the addition of $SF_6$ gas due to formation of nonvolatile fluorine compounds inhibiting reaction between oxygen and hydrocarbon polymer, while applying substrate bias enhances etching process through physical attack. However, addition of small amount of $SF_6$ is desirable for etching topography. $SiO_2$ hard mask for polyimide etching is effective under $O_2$plasma etching(selectivity~30), while $O_2/SF_6$ chemistry degrades etching selectivity down to 4. Based on the above results, $1-2\mu\textrm{m}$ L&S PI2610 patterns were successfully etched.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.138-138
• /
• 2003

광대역 LiNbO$_3$ 광변조기의 초고속 광 변조 구현을 위해서는 RF/ optical 속도 정합 및 임피던스 매칭 조건 하에서 낮은 구동전압을 얻을 수 있는 ridge 구조의 제작이 필수적이며 이런 구조 제작하기 위해서는 식각 속도와 식각면 거칠기 식각 profile 및 식각 과정에서의 반응물의 감소 등과 같은 개선을 위한 연구가 필요하다. 본 연구에서는 LiNbO$_3$ 기판 위에 메탈 마스크를 형성한 후 비등방성 (anisotropic) 건식 식각 방법인 NLD (Neutral Loop Discharge)로 플라즈마 식각을 하였다. NLD plasma 식각은 1Pa 이하의 압력에서 낮은 전자 온도를 갖는 고밀도 플라즈마를 생성하고 이온 플라즈마를 형성하여 LiNbO$_3$ 표면의 원자와 분자를 이온충돌효과를 이용하여 물리적인 식각과 discharge로 형성된 레디칼 (radical)과의 상호작용에 의한 화학적 식각 메커니즘에 의한 방법으로 plasma에 의한 시편의 손상이 적으며 식각 속도가 또한 높은 것이 특징이다. 본 논문에서는 안테나 파워와 가스의 유량에 따른 LiNbO$_3$ 식각 profile 특성에 관하여 연구 하고자 한다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.363-363
• /
• 2010

The high capillarity of a plastic fiber network having superhydrophilic Si-DLC coating is studied. Although the superhydrophilic surface maximize wetting ability on the flat surface, there remains a requirement for the more wettable surface for various applications such as air-filters or liquid-filters. In this research, the PET non-woven fabric surface was realized by superhydrophilic coating. PTE non-woven fabric network was chosen due to its micro-pore structure, cheap price, and productivity. Superhydrophobic fiber network was prepared with a coating of oxgyen plasma treated Si-DLC films using plasma-enhanced chemical vapor deposition (PECVD). We first fabricated superhydrophilic fabric structure by using a polyethylene terephthalate (PET) non-woven fabric (NWF) coated with a nanostructured films of the Si-incorporated diamond-like carbon (Si-DLC) followed by the plasma dry etching with oxygen. The Si-DLC with oxygen plasma etching becomes a superhydrophilic and the Si-DLC coating have several advantages of easy coating procedure at room temperature, strong mechanical performance, and long-lasting property in superhydrophilicity. It was found that the superhydrophobic fiber network shows better wicking ability through micro-pores and enables water to have much faster spreading speed than merely superhydrophilic surface. Here, capillarity on superhydrophilic fabric structure is investigated from the spreading pattern of water flowing on the vertical surface in a gravitational field. As water flows on vertical flat solid surface always fall down in gravitational direction (i.e. gravity dominant flow), while water flows on vertical superhydrophilic fabric surface showed the capillary dominant spreading.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.6
• /
• pp.234-238
• /
• 2005

Effects of plasma composition, ion flux and ion energy on the etch rate, surface morphology and near surface stoichiometry of a single crystalline $La_3Ga_5SiO_{14}$ wafer have been examined in $Cl_2/Ar$ inductively coupled plasma (ICP) discharges. Maximum etch rate ${\sim}1600{\AA}/min$ was achieved either at relatively high source power $({\sim}1000W)$ or high $Cl_2$ content conditions in $Cl_2/Ar$ discharges. The etched surfaces showed similar or better RMS roughness values than those of the unetched control sample and the near surface stoichiometry was found not to be affected by ICP etching.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.11
• /
• pp.826-830
• /
• 2013

In this paper, we carried out the investigations of both etch characteristics and mechanisms for the $SnO_2$ thin films in $O_2/BCl_3/Ar$ plasma. The dry etching characteristics of the $SnO_2$ thin films was studied by varying the $O_2/BCl_3/Ar$ gas mixing ratio. We determined the optimized process conditions that were as follows: a RF power of 700 W, a DC-bias voltage of - 150 V, and a process pressure of 2 Pa. The maximum etch rate was 509.9 nm/min in $O_2/BCl_3/Ar$=(3:4:16 sccm) plasma. From XPS analysis, the etch mechanism of the $SnO_2$ thin films in the $O_2/BCl_3/Ar$ plasma can be identified as the ion-assisted chemical reaction while the role of ion bombardment includes the destruction of the metal-oxide bonds as well as the cleaning of the etched surface form the reaction products.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.258-258
• /
• 2009

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.11a
• /
• pp.628-631
• /
• 2004

A tetrafluoromethane$(CF_4)$ is most useful gas in plasma dry etching, because it has a electron attachment cross-section. therefor it is important to calculate transport coefficients like electron drift velocity, ionization coefficient, attachment coefficient, effective ionization coefficient. and critical E/N. The aim of this study is to get these transport coefficients for information of the insulation strength and efficiency of etching process. Electron transport coefficients in $CF_4+Ar$ gas mixture are simulated in range of E/N values from 1 to 250 [Td] at 300[K} and 1 [Torr] by using Boltzmann equation method. The results of this method can be important data to present characteristic of gas for plasma etching and insulation, specially critical E/N is a data to evaluate insulation strength of a gas. and is presented in this paper for various mixture ratios of $CF_4+Ar$ gas mixture.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.3
• /
• pp.164-169
• /
• 2014

We investigated the etching characteristics of $HfAlO_3$ thin films in $O_2/Cl_2/Ar$ and $O_2/BCl_3/Ar$ gas, using a high-density plasma (HDP) system. The etch rates of the $HfAlO_3$ thin film obtained were 30.1 nm/min and 36 nm/min in the $O_2/Cl_2/Ar$ (3:4:16 sccm) and $O_2/BCl_3/Ar$ (3:4:16 sccm) gas mixtures, respectively. At the same time, the etch rate was measured as a function of the etching parameter, namely as the process pressure. The chemical states on the surface of the etched $HfAlO_3$ thin films were investigated by X-ray photoelectron spectroscopy. Auger electron spectroscopy was used for elemental analysis on the surface of the etched $HfAlO_3$ thin films. These surface analyses confirm that the surface of the etched $HfAlO_3$ thin film is formed with nonvolatile by-product. Also, Cl-O can protect the sidewall due to additional $O_2$.

• Transactions on Electrical and Electronic Materials
• /
• v.13 no.6
• /
• pp.287-291
• /
• 2012

We investigated the etching characteristics of TaN thin films in an $O_2/BCl_3/Cl_2/Ar$ gas using a high density plasma (HDP) system. A maximum etch rate of the TaN thin films and the selectivity of TaN to $SiO_2$ were obtained as 172.7 nm/min and 6.27 in the $O_2/BCl_3/Cl_2/Ar$ (3:2:18:10 sccm) gas mixture, respectively. At the same time, the etch rate was measured as a function of the etching parameters, such as the RF power, DC-bias voltage, and process pressure. The chemical states on the surface of the etched TaN thin films were investigated using X-ray photoelectron spectroscopy. Auger electron spectroscopy was used for elemental analysis on the surface of the etched TaN thin films. These surface analyses confirm that the surface of the etched TaN thin film is formed with the nonvolatile by-product.