• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.8 s.111
• /
• pp.746-752
• /
• 2006

In this paper, a compact partial H-plane filter with periodic structure is proposed. Guided wavelength of periodic structure' is reduced by slow wave effect. Cross-section and length of partial H-plane filter with periodic structure are considerably reduced by 75% and 30%, respectively, as compared with conventional E-plane filter. In addition, spurious responses of the bandpass filter are improved. To design bandpass filter with periodic structure, we have analyzed a periodic structure of partial H-plane waveguide and derived equations of the periodic filter. Measured results are in good agreement with simulated results.

• Journal of Electrochemical Science and Technology
• /
• v.8 no.3
• /
• pp.250-256
• /
• 2017

A graphene electrode with a novel in-plane structure is proposed and successfully adopted for use in supercapacitor applications. The in-plane structure allows electrolyte ions to interact with all the graphene layers in the electrode, thereby maximizing the utilization of the electrochemical surface area. This novel structure contrasts with the conventional out-of-plane stacked structure of such supercapacitors. We herein compare the volumetric capacitances of in-plane- and out-of-plane-structured devices with reduced multi-layer graphene oxide films as electrodes. The in-plane-structured device exhibits a capacitance 2.5 times higher (i.e., $327F\;cm^{-3}$) than that of the out-of-plane-structured device, in addition to an energy density of $11.4mWh\;cm^{-3}$, which is higher than that of lithium-ion thin-film batteries and is the highest among in-plane-structured ultra-small graphene-based supercapacitors reported to date. Therefore, this study demonstrates the potential of in-plane-structured supercapacitors with high volumetric performances as ultra-small energy storage devices.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.54 no.4
• /
• pp.39-46
• /
• 2012

The objectives of this study is intended to analyze stresses using the boundary element method and probability analysis for agricultural structure. Loads and material properties are an important factor when analyzing the structure. Until now, designing structure, loads and material properties are applied deterministic value. However, load and material properties involve uncertainties due to those change probabilistic and deterministic methods could not consider uncertainties. To solve these problems, the reliability analysis based on probability properties scheme was developed. Reliability analysis is easy to approach to analysis frame structure, however it has limitation when solving plane stress strain problems a kind of agricultural structures. The BEM (Boundary Element Method) is able to analysis plane strain problems by boundary conditions. Thus, this study applied boundary element method to analysis plane strain problem, load and material properties as a probabilistic value to calculate the analytical model using Monte Carlo simulations were developed.

• Journal of the Architectural Institute of Korea Structure & Construction
• /
• v.34 no.6
• /
• pp.11-18
• /
• 2018

Isogeometric concept is introduced to find out the optimum layout of plane structure under free vibration. Eigenvalue problem is formulated and numerically solved in order to obtain natural frequencies and mode shapes of plane structures. For the exact geometric expression of the structure, the Non-Uniform Rational B-spline Surface (NURBS) basis functions is employed and it is also used to define the material density functions. A node-wise design variables is adopted to deal with the updating of material density in topology optimization (TO). The definition of modal strain energy is employed to achieve the maximization of fundamental frequency through its minimization. The verification of the proposed TO technique is performed by a series of benchmark test for plane structures.

• Bulletin of the Korean Mathematical Society
• /
• v.46 no.3
• /
• pp.447-461
• /
• 2009

In this paper we give a non-existence theorem for Hopf real hypersurfaces in complex two-plane Grassmannians $G_2(\mathbb{C}^{m+2})$ satisfying the condition that the structure Jacobi operator $R_{\xi}$ commutes with the 3-structure tensors ${\phi}_i$, i = 1, 2, 3.

• Kyungpook Mathematical Journal
• /
• v.59 no.3
• /
• pp.525-535
• /
• 2019

In relation to the generalized Tanaka-Webster connection, we consider a new notion of parallel structure Jacobi operator for real hypersurfaces in complex two-plane Grassmannians and prove the non-existence of real hypersurfaces in $G_2({\mathbb{C}}^{m+2})$ with generalized Tanaka-Webster parallel structure Jacobi operator.

• Smart Structures and Systems
• /
• v.20 no.5
• /
• pp.563-572
• /
• 2017

The safety of structures is closely associated with the structural out-of-plane behavior. In particular, long and slender beam structures have been increasingly used in the design and construction. Therefore, an evaluation of the lateral and torsional behavior of a structure is important for the safety of the structure during construction as well as under service conditions. The current contact measurement method using displacement meters cannot measure independent movements directly and also requires caution when installing the displacement meters. Therefore, in this study, a vision-based system was used to measure the in-plane and out-of-plane displacements of a structure. The image processing algorithm was based on reference objects, including multiple targets in Lab color space. The captured targets were synchronized using a load indicator connected wirelessly to a data logger system in the server. A laboratory beam test was carried out to compare the displacements and rotation obtained from the proposed vision-based measurement system with those from the current measurement method using string potentiometers. The test results showed that the proposed vision-based measurement system could be applied successfully and easily to evaluating both the in-plane and out-of-plane movements of a beam including twisting rotation.

• Bulletin of the Korean Mathematical Society
• /
• v.45 no.3
• /
• pp.495-507
• /
• 2008

In this paper we give a complete classification of real hyper-surfaces in complex two-plane Grassmannians $G_2({\mathbb{C}}^{m+2})$ with commuting structure Jacobi operator $R_{\xi}$ and another geometric condition.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.5 no.4
• /
• pp.74-81
• /
• 1996

This paper is to estimate sizing design sensitivity of linear and nonlinear vehicle frame structure using structural ananlysis result from ANSYS. Using design sensitivity results, optimal design of plane vehicle frame structure with buckling constraint is carried out the gradient projection method. Optimal design results are compares gradient projection method resrult with SUMT result.

• Journal of applied mathematics & informatics
• /
• v.39 no.3_4
• /
• pp.327-338
• /
• 2021

In this paper, we have introduced a new notion of recurrent structure Jacobi of real hypersurfaces in complex hyperbolic two-plane Grassmannians G^*₂(ℂ^m+2). Next, we show a non-existence property of real hypersurfaces in G^*₂(ℂ^m+2) satisfying such a curvature condition.