• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.661-670
• /
• 2005

In this paper, the microstrip $90^{\circ}$ hybrid to provide -3dB coupling and $90^{\circ}$ phase difference at broadband frequency range of 2 to 6 GHz is designed. This proposed hybrid is composed of 3-section. The two outside section are realized by symmetrical edge coupled lines, but on the other hand the middle section consists of VIP(Vertically Installed Planar) circuit. The ground part of VIP circuit is partially removed to get tight coupling, particularly. This hybrid is easy to realize due to microstrip structure and has good holing flexibility by taking advantage of VIP circuit as a control point of optimization. The proposed hybrid provide satisfactory performance as compared with simplicity of structure and fabrication first of all.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.6
• /
• pp.919-930
• /
• 2001

This paper presents a wideband technique of impedance and axial-ratio bandwidth which uses the stacked planar array structure through optimum design of sub-polarization generating sections and parasitic patch. So, the effect of the dual-resonance characteristic can contribute to the bandwidth expansion of single fed planar array antenna using circular polarization which doesn\`t hire previous bandwidth expansion technique. The antenna can be used as a dual-band antenna by adjusting the resonance frequencies as well, and then the antenna is designed and fabricated in the frequency band of domestic satellite-TV service. This antenna has the performance of 9.7 % impedance bandwidth and 24 dBi of antenna gain. And it has also 2.8 % and 1.4 % of 3 dB Axial-ratio bandwidth at 11.4 GHz and 11.8 GHz respectively.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2005.11a
• /
• pp.249-254
• /
• 2005

This paper presents the design of a novel small and wide band planar inverted F-antenna which simultaneously covers GSM900/GPS/DCS1800/DCS1900/DMB service. The proposed antenna consisting of a main patch with rectangular slit, strip 1 and strip 2, occupied the total volume of.$15\times36\times6mm^3$. A very wide impedance bandwidth characteristic was achieved by optimizing both the distance between the feed line and short strip and the length of rectangular slit on the main patch. The commercial electromagnetic software, CST Microwave Studio, is used to design the structure. The maximum gains at the frequencies of 900, 1575, 1800, 1900, and 2600 MHz were 2.07, 1.07, 1.69 and 0.55, -1.99 dBi, respectively. The overall shape of the radiation patterns is suitable for mobile communication application.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.8
• /
• pp.739-745
• /
• 2009

This paper presents a design for trapezoidal planar UWB(Ultra Wide-band) antenna using symmetry meander line to realize broad bandwidth at low frequency region. The size of proposed design antenna is $15.5{\times}21{\times}1.6mm^3$ and dielectric substrate considered in design has 4.4 of relative permittivity. The calculated bandwidth is from 1.31 GHz to 10.83 GHz and the measured return loss is 1.5 GHz to 10.6 GHz at -10 dB below, and satisfies with the UWB antenna's bandwidth. The simulated and measured radiation patterns show fine agreement with each other at each frequency.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.9 no.8
• /
• pp.861-866
• /
• 2014

This study evaluates the modeling accuracy of the existing three phase shift models on which the time domain oscillator phase noise theories are based. For the evaluation, this study investigates how accurately the three models can model the phase shift impulse train response of a simple planar oscillator. Evaluation result reveals that Kaertner model most accurately reflects the oscillator's phase shift impulse train responses for five different impulse train inputs, whereas PP model exhibited the worst performance in modeling the phase shift impulse train responses.

• Journal of computational fluids engineering
• /
• v.15 no.1
• /
• pp.31-36
• /
• 2010

In the present study, computations for flow fields inside the CDI unit cells with electrodes and spacers have been made to evaluate their performance. Three types of unit cells that include a planar type, a serpentine channel type, and a spiral wound type were considered and their flow characteristics were compared. From the computational results, it is found that the serpentine channel type has a large flow resistance and can not guarantee the outflow flux for industrial applications. On the other hand, the planar type can sustain a large enough outflow flux but it's efficiency is low for the electrode-use because of the non-uniform velocity distribution inside the cell and dead zones in every corner. Finally, The spiral wound type has not only a large outflow flux as much as the planar type has, but also a high efficiency for the electrode-use because of uniform velocity distribution. From this comparison, we can expect that the spiral wound type of CDI unit cell would have a high performance deionization capability.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.3 no.4
• /
• pp.149-155
• /
• 1983

A numerical procedure based on the finite element method for the nonlinear analysis of planar reinforced concrete frames is presented. Material nonlinearities such as cracking of concrete and yielding of steel are incorporated. This method is capable of providing accurate numerical solutions for the response of planar reinforced concrete frames failing primarily, in flexure throughout elastic, inelastic and ultimate load ranges. A numerical example is presented to demonstrate the validity and applicability of the present method. The results are compared with experimental results and the analytical results obtained by other investigator.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.10 no.2
• /
• pp.21-27
• /
• 2014

In this paper, a planar sleeve monopole antenna for indoor digital TV reception is presented. The antenna has broadband property with the planar monopole and ground of sleeve. Sleeve monopole and ground conductors of the antenna are on the same plane, and exited through CPW feeding. Sleeve monopole and ground of proposed antenna exist on coplanar plane, and excite as CPW. It used FR4 epoxy dielectric substrate of ${\varepsilon}r=4.4$, and the size is $20[mm]{\times}170[mm]{\times}1.6[mm]$ dimension. So the internal antenna is suitable. The measurement results of the fabricated antenna, return loss is larger than -10 [dB] in 470~806 [MHz]. Maximum gain is 0.59 [dBi] on E-plane at 810 MHz and 1.70 [dBi] on H-plane at 640 [MHz]. Radiation pattern is about the same that of dipole antenna at all frequency.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.3
• /
• pp.452-460
• /
• 2002

The precision stage using a novel contact-free planar actuator based on magnetic farces, magnetized force and Lorentz farce, is suggested. In the promising magnetic structure, the mover is driven directly without any transmission mechanism, and doesn't need any auxiliary driver for its posture calibration. Then it is estimated that the proposed operating principle is very suitable for work requiring high accuracy and cleanness, or general-purpose nano-stage. In this paper, we discuss a driving principle of the planar system including the magnetic force generation mechanism, a framework for the force model, governing characteristics of the levitated plate, and a planar motion control of the constructed prototype. And experimental results are given to verify the derived theoretical model and a feasibility of the system.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.1-4
• /
• 2008

Fuel cells have the potential of providing several times higher energy storage densities than those possible using current state-of-the-art lithium-ion batteries, but current energy density of fuel cell system is not better than that of lithium-ion batteries. To achieve the high energy density, volume and weight of fuel cell system need to be reduced by miniaturizing system components such as stack, fuel tank, and balance-of-plant. In this paper, the thin flexible PCB (Printed circuit board) is used as a current collector to reduce the stack volume. Two end plates are made from light weight aluminum alloy plate. The plate surface is wholly oxidized through the anodizing treatment for electrical insulation. The opening rate of cathode plate hole is optimized through unit cell performance measurement of various opening rates. The performances are measured at room temperature and ambient pressure condition without any repulsive air supply. The active area of MEA is 10.08 $cm^2$ and active area per a unit cell is 1.68 $cm^2$. The peak power density is about 210 mW/$cm^2$ and the air-breathing planar stack of 2 Wis achieved as a small volume of 18 cc.