• Journal of Sensor Science and Technology
• /
• v.17 no.3
• /
• pp.178-182
• /
• 2008

Planar type micro catalytic combustible gas sensor was developed by using nano crystalline $SnO_2$ Pt thin film as micro heater was deposited by thermal evaporation method on the alumina substrate. The thickness of the Pt heater was around 160 nm. The sensor showed high reliability with prominent selectivity against various gases(Co, $C_3H_8,\;CH_4$) at low operating temperature($156^{\circ}C$). The sensor with nano crystalline $SnO_2$ showed higher sensitivity than that without nano crystalline $SnO_2$. This can be explained by more active adsorption and oxidation of hydrogen by nano crystalline $SnO_2$ particles. The present planar-type catalytic combustible hydrogen sensor with nano crystalline $SnO_2$ is a good candidate for detection of hydrogen leaks.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.14 no.4
• /
• pp.347-351
• /
• 2008

In this paper, a new co-planar waveguide ultra-wideband aperture is designed as wireless application in ships. The designed antenna consists of a rectangular aperture on a determined ground plane and a mushroom shaped stub. The mushroom-shaped stub, which is simple, convenient to analyze and optimise, has less parameters. This antenna has compact aperture size $21.1{\times}8.1mm^2$, designed on FR-4 substrate with dielectric constant of 4.3, thickness of 1.5mm. CPW fed planar antenna has the advantages of wide-bandwidth, low-cost and easy interaction with the radio frequency front end circuitry.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.865-868
• /
• 2001

We designed and fabricated a planner-type thermoelastic microactuator with a latch-up operation for optical switching. Latch-up actuation is prerequisite to implement an optical switch with low power consumption and high reliability. The proposed microactuator consists of four cantilever-shaped thermal actuators, four displacement linkages, two shallow arch-shaped leaf springs, a mobile shuttle mass with a micromirror, and four elastic boundaries. The structural layer of the planar microactuator is phosphorous-doped 12$\mu\textrm{m}$-thick polysilicon, and the sacrificial layer is LTO(Low Temperature Oxide) of 3$\mu\textrm{m}$thickness. The displacement of actuator is as large as 3$\mu\textrm{m}$when the length of actuation bar is 100$\mu\textrm{m}$in length at 5V input voltage. The proposed microactuators have advantages of easy assembly with other optical component by way of fiber alignment in the substrate plane, and its fabrication process features simplicity while retaining batch-fabrication economy.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.8
• /
• pp.2247-2254
• /
• 2010

The surface structures of copper phthalocyanine (CuPc) thin films deposited on sulphur-passivated and plane perylene-3,4,9,10-tetracarboxylic dianhydride (PTCDA)-covered InAs(100) surfaces have been studied by low energy electron diffraction (LEED) and van der Waals (vdW) intermolecular interaction energy calculations. The annealing to $300^{\circ}C$ and $450^{\circ}C$ of $(NH_4)_2S_x$-treated InAs(100) substrates produces a ($1{\times}1$) and ($2{\times}1$) S-passivated surface respectively. The CuPc deposition onto the PTCDA-covered InAs(100) surface leads to a ring-like diffraction pattern, indicating that the 2D ordered overlayer exists and the structure is dominantly determined by the intermolecular interactions rather than substrate-molecule interactions. However, no ordered LEED patterns were observed for the CuPc on S-passivated InAs(100) surface. The intermolecular interaction energy calculations have been carried out to rationalise this structural difference. In the case of CuPc unit cells on PTCDA layer, the planar layered CuPc structure is more stable than the $\alpha$-herringbone structure, consistent with the experimental LEED results. For CuPc unit cells on a S-($1{\times}1$) layer, however, the $\alpha$-herringbone structure is more stable than the planar layered structure, consistent with the absence of diffraction pattern. The results show that the lattice structure during the initial stages of thin film growth is influenced strongly by the intermolecular interactions at the interface.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.10a
• /
• pp.303-307
• /
• 2008

In this paper, a new co-planar waveguide ultra-wideband aperture is designed. The designed antenna consists of a rectangular aperture on a determined ground plane and a mushroom shaped stub. The mushroom-shaped stub, which is simple, convenient to analyze and optimise, has less parameter. This antenna has compact aperture size $21.1{\times}8.1mm^2$, designed on FR-4 substrate with dielectric constant of 4.3, thickness of l.5mm. CPW fed planar antenna has the advantages of wide-bandwidth, low-cost and easy interaction with the radio frequency front end circuitry.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.437-438
• /
• 2007

In this paper a embedded decoupling capacitor design with gap structure will be discussed. A novel structure is modeling and analization by High Frequency Structure Simulator (HFSS). Proposed capacitor have $2m{\times}2m$ in rectangular shape. The film thickness of copper/dielectric film/substrate is respectively 35um/20um/35um. A dielectric layer of BaTiO3/epoxy has the relative permittivity of 25. Compare of the planar decoupling capacitor, capacitance densities of this structure in the range of $55{\mu}F$/mm2 have been obtained with 50um gap while capacitance densities of planar structure $55{\mu}F$/mm2 in the same size. The frequency dependent behavior of capacitors is numerically extracted over a wide frequency bandwidth 500MHz-7GHz. The decoupling capacitor can work at high frequency band increasing the gap size.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.7
• /
• pp.840-843
• /
• 2012

In this paper, the authors present a new design for a dual-band metamaterial(MTM) absorber that utilizes resonant-magnetic inclusion of a split-ring resonator(SRR). The proposed MTM unit cell is constructed by two open complementary split-ring resonators(OCSRRs) and an SRR arrangement. To avoid the need for metallic back plate a planar array of SRRs for resonant-magnetic inclusion is placed facing toward the incident wave propagation direction. Each unit cell is printed on the two sides of a FR-4 substrate. A prototype absorber was fabricated with a planar array of $39{\times}39$ unit cells, and measured. The proposed backplane-less absorber can be used for microwave applications.

• Korean Journal of Materials Research
• /
• v.29 no.1
• /
• pp.59-64
• /
• 2019

This study investigates the optical characteristics of InGaN multiple quantum wells(MQWs) light emitting diodes(LEDs) on planar sapphire substrates(PSSs), nano-sized PSS(NPSS) and micro-sized PSS(MPSS). We obtain the results as the patterning size of the sapphire substrates approach the nanometer scale: The light from the back side of the device increases and the total light extraction becomes larger than the MPSS- and planar-LEDs. The experiment is conducted by Monte Carlo ray-tracing, which is regarded as one of the most suitable ways to simulate light propagation in LEDs. The results show fine consistency between simulation and measurement of the samples with different sized patterned substrates. Notably, light from the back side becomes larger in the NPSS LEDs. We strongly propose that the increase in the light intensity of NPSS LEDs is due to an abnormal optical distribution, which indicates an increase of extraction probability through NPSS.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2008.05a
• /
• pp.685-688
• /
• 2008

Planar antennas are very efficient for the use of the out-door data transmission applications due to their low-profile characteristics. But the size of the antenna in UHF band blocks the practical usage. In this paper, a miniaturized planar antenna is investigated for the application of AMR system in UHF band. The designed antenna is fabricated in the form of the microstrip patch on the FR-4 substrate. The miniaturization is achieved by slot-loading on the patch. First, effects of simple slots on the size reduction are analyzed, followed by the design using more complex slots resulting in the reduction ratio of 37.9% in 425.6 MHz and bandwidth of 3.8 MHz. The effect of epoxy coating for the protection is also investigated.

• Journal of the Microelectronics and Packaging Society
• /
• v.22 no.4
• /
• pp.25-29
• /
• 2015

Demand for a low-cost, high-throughput, and high-resolution patterning method for fabricating devices continues to increase. The roll-to-roll (R2R) imprint lithography technique has received a great deal of attention as a means of fabricating next-generation devices. In this paper, we propose a fabrication method for polymeric planar lightwave circuit (PLC) devices that uses R2R imprint lithography. The proposed technique uses an elastomeric polydimethylsiloxane (PDMS) mold. A Si wafer with micro patterns is used as the Si master. The PDMS mold is then replicated from the Si master. By applying a precise web tension and at a given web speed, we fabricated a micro-patterned PLC device. The insertion losses were 4.0 dB for a $1{\times}2$ optical splitter. As such, the proposed method of fabricating a PLC device by the R2R process was shown to be an effective solution.