• Proceedings of the KWS Conference
• /
• 2004.05a
• /
• pp.319-320
• /
• 2004

1960년대에 Engineering 폴리에틸렌(Polyethylene, 기후 PE로 표기함) 수지가 소개된 이후 현재까지 PE수지는 광범위한 분야에 적용되어왔다. 또한, PE 수지파이프는 내식성이 뛰어나고 가볍고 유연성(flexibility)이 우수하다는 특징을 가지고 있다. (중략)

• International Journal of Korean Welding Society
• /
• v.1 no.1
• /
• pp.1-6
• /
• 2001

This paper describes several advances in sensor and process control techniques for applications in Submerged Arc Welding (SAW), which combine to give a fully automatic system capable of controlling and adapting the overall welding process. This technology has been applied in longitudinal and spiral pipe mills and in pressure vessel production.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.49-51
• /
• 2005

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.33-35
• /
• 2007

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.191-193
• /
• 2005

• Proceedings of the KWS Conference
• /
• 2005.06a
• /
• pp.220-222
• /
• 2005

• Journal of Welding and Joining
• /
• v.5 no.2
• /
• pp.44-52
• /
• 1987

The fracture toughness, $J_{IC}$ of high frequency electric resistance welded steel pipe for smooth and side-grooved CT specimen was evaluated by unloading compliance method. The crack growth, .${\delta}a$ was obtained from the equation of Donald and Saxena & Hudak, and $J_{IC}$ was determined from the curve of J-${\delta}a$ relations. The crack growth on the experiment using unloading compliance method is underestimated as compared with ${\delta}a$ measured directly by the SEM, so the reliability of $J_{IC}$ from saxena & Hudak equation is large than that from Donald. The $J_{IC}$ value of side-grooved CT Specimen is estimated less than that of smooth, and this is the effect of the side-groove, the shear-lip of crack tip and the reduction of crack tunnelling phenomena.

• Journal of Welding and Joining
• /
• v.12 no.4
• /
• pp.41-49
• /
• 1994

This study is to compare the welding quality of API 5L-X65 Steel- pipe's for natural gas transmission piping applied by SAW at shop and by GTAW-SMAW at site. The results can be summarized as follows; 1) Tensile strength of the welded zone by SAW(611.5 MPa) and by GTAW-SMAW(608.6 MPa) was maintained greater than that of the base metal(583.5 MPa). 2) Hardness of the welded zone and HAZ by SAW(Hv 194.8) & GTAW-SMAW (Hv 196.1) was slightly increased above that of the base metal (Hv 168.8), but less than the maximum allowable hardness(Hv 248). 3) Impact value of the welded zone by SAW(126.8 J) & GTAW-SMAW(88 J) became lower than that of the base metal(282.5 J), but was above the requirement of API 5L(68J). 4) Microscopic structure of the welded zone and HAZ by both SAW & GTAW-SMAW became fine-grained.

• Journal of Welding and Joining
• /
• v.32 no.3
• /
• pp.89-94
• /
• 2014

AISI 304 austenitic stainless steel is widely used for LNG pipes for LNG transmission thanks to its good metallurgical and mechanical properties. In the present research, impact toughness of a gas tungsten arc welded AISI 304 stainless steel pipe was evaluated between room and liquid nitrogen ($-196^{\circ}C$) test temperatures. In addition, a comparative study was made of the fracture behavior of FCC crystal structured stainless steel weldments and BCC crystal structured mild steels(A-grade and SS400). The results showed a slight decrease in the impact energy of the AISI 304 base metal, heat affected zone(HAZ), and welded zone with decreasing test temperature. In addition, the welded metal has the highest absorbed impact energy, followed by HAZ and the base metal.

• Journal of Welding and Joining
• /
• v.19 no.4
• /
• pp.413-422
• /
• 2001

In this study. two-dimensional heat flow and residual stress in arc brazing to join the pipe and plate structure were analyzed by using a commercialized FEM package. Advantages offered by arc brazing are that strong joints can be produced with lower heat input than that of previous gas metal arc welding and narrower heat affected zone can usually be obtained than that in the case of torch brazing. To investigate the effects of process variables and minimize the thermal effects on the structure, this study presents a method for analyzing the heat flow and residual stress in arc brazing process according to variables such as traveling speed, torch angle and position. The simulation results were compared with the experimental ones to verify the numerical analysis method. The experiments include the measurement of HAZ size from the section of joints and residual stresses by using strain gages named 'section method'. A comparatively good agreement between the results of numerical analysis and experimental ones could be obtained in both of the temperature distribution and residual stress of the brazed structure. Using the proposed numerical analysis method, the process parameters were evaluated to get proper arc brazing conditions.