• 설비공학논문집
• /
• 제5권4호
• /
• pp.295-305
• /
• 1993

Thermal performance of test cell of model hot water Ondol house was simulated by equivalence heat resistence and heat capacity method. In this method wall was replaced by two equivalence and one heat capacity. This method enables to simulate the variation of temperature of each element of model house. The effect of pipe diameter, pitch of pipe and with or without consideration of inter-radiation between wall surfaces on the energy consumption rate were investgated. Results show that radiations between the ground surface of room and wall surfaces contribute to the heating of room air by reducing the convection heat loss through the wall surfaces.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권7호
• /
• pp.997-1008
• /
• 2010

The mooring line tension and motion response of a floating fish reef system were analyzed using a Morison equation type numerical model. The reef structure was constructed with pipe and suspended up from the bottom with a single, high tension mooring. Input forcing parameters into the model consisted of both regular and random waves, with and without currents. Heave, surge and pitch dynamic calculations were made, along with the tension response in the mooring lines. Results were analyzed in both the time and frequency domains and where appropriate, linear transfer functions were calculated. In addition, damped and natural periods of the system were determined to examine a resonating situation.

• 비파괴검사학회지
• /
• 제24권2호
• /
• pp.142-150
• /
• 2004

발전설비의 보수검사에 적용하기 위한 예비 연구로 comb transducer를 이용한 파이프 내에서의 유도초음파 모드의 거동을 실험적으로 검증하였다. 유도초음파의 모드식별은 STFT와 WT에 의한 시간-주파수해석을 통하여 최적의 모드를 선정하였다. 시간-주파수해석과 이론적 해석 방법인 분산 곡선을 비교한 결과 잘 일치함을 알 수 있었으며, pitch-catch법과 선단부로부터 반사된 신호를 모드 분석한 결과 L(0,1) 모드가 다른 모드에 비해 모드변환에 의한 영향이 적었다. 따라서 L(0,1)을 최적의 모드로 선정하고, 결함위치를 추정한 결과 유용함을 알 수 있었다.

• 대한기계학회논문집B
• /
• 제30권4호
• /
• pp.381-388
• /
• 2006

The objective of this study is to predict the etching characteristics using spray characteristics for the optimization on the etching process of Lead-Frame. The etching characteristics such as etching factor, uniformity were investigated on the actual operating conditions. The correlation between the etching characteristics and the spray ones obtained by measurement were analyzed to simulate the etching characteristics according to actual conditions of lead-frame etching process. These conditions of lead-frame process were spray pressure, distance from nozzle tip to substrate, pipe pitch, and nozzle pitch. To improve the etching characteristics in the lead-frame process, effects of the various operating conditions should be understood in detail. The spray characteristics obtained by experiment using PDA system were simulated by the Monte-Carlo method. The etching process model was coded by Java language. It was found that simulation results generally agreed well with the measured results of etching characteristics in lead-frame etching process. The optimal operating parameters were successfully found under variable conditions.

• Nuclear Engineering and Technology
• /
• 제27권6호
• /
• pp.888-893
• /
• 1995

맨봉 배열에 의해 형성되는 부수로를 흐르는 난류 유동장의 구조는 피치 대 봉직경의 비에 따라 변하게 된다. 피치 대 봉직경 비가 큰 경우에는 난류 응력 분포가 관 유동의 분포와 유사하다 그러나 피치 대 봉직경 비가 작은 경우에는 특히 간극 영역에서 난류 특성이 관 유동의 분포와는 달라진다. 완전히 발달된 맨봉 주위의 난류 유동장에서 난류응력과 난류운동에너지 사이의 선형 관계가 개발되었다. 개발된 상관 관계식은 난류 연구에 응용되는 여러 이론적 분석에 연관지어 사용될 수 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1611-1616
• /
• 2004

The objective of this study is to simulate the etching characteristics under different process parameters for the optimization of etching process. The etching characteristics such as the etching factor were investigated under different operating conditions and compared with the spray characteristics. The spray characteristics were measured by using Phase Doppler Anemometer. The correlation between the etching characteristics and the spray characteristics was analyzed to simulate the etching characteristics under the actual parameters of the etching process. The parameters were distance of nozzle tip and pipe pitch. To improve the uniformity and value of etching factor in the etching process, the process parameters should be designed optimally. The distribution of spray was simulated by the Monte-Carlo Method and the process parameters were optimized by the design of experiments(DOE).

• 비파괴검사학회지
• /
• 제31권3호
• /
• pp.271-277
• /
• 2011

This study presents a nondestructive test for underwater PVC pipes. To use guided ultrasonic waves, specially denoted by cylindrical Lamb waves, a test setup was made in a water tank using the pitch and catch mode and specimens were made to give artificial cutouts located in the circumferential direction of the pipes. Total three states of damaged levels were considered to see how the guided waves interact with the defects. For the experimental adjustments, three different pipe diameters (60, 90, 114 mm) were tested, and two factors - incident angle (10 and $40^{\circ}$) and distance (50 and 200 mm) - were tried. From the results, regardless of the diameters and two experimental factors, it is shown that the degrees of defects were recognized through amplitude and arrived time of the very first part of the received cylindrical Lamb waves. Between amplitude and arrived time, it is found that the amplitude gives more sensitive results.

• International Journal of Precision Engineering and Manufacturing
• /
• 제8권1호
• /
• pp.73-78
• /
• 2007

The objective of this work was to simulate lead frame etching characteristics to optimize the etching process, Characteristics such as the etching factor and uniformity were investigated for different actual operating conditions, including pressure, distance from the nozzle tip, pipe pitch, and feed speed. The correlation between the etching and spray characteristics was analyzed to develop the etching model. Spray characteristics obtained from an experiment using a phase Doppler anemometer system were then simulated using a Monte-Carlo technique, The etching process model was coded in the Java language, The spray and etching characteristics were correlated with each other and simulated results agreed well with the measured data for a lead frame etching process, The optimal operating parameters under various conditions were successfully determined.

• 대한기계학회논문집
• /
• 제18권9호
• /
• pp.2486-2493
• /
• 1994

Transient heat transfer characteristics in th radiant heating panel with heat diffusion fin were predicted by numerical analysis. Thermal behaviors of panel, such as temperature distributions in panel and convective and radiative heat fluxes in panel surface with advance of time, were obtained for several important parameters. The performance and thermal comfort of heating panel were studied and compared for various design conditions, such as pipe pitch, area ratio and thermal conductivity of optimal design of the new heating panels with heat diffusion fin. It was concluded that the efficient area ratio of heat diffusion fin is about 0.5, and the greater the thermal conductivity of fin is, the better the performance of panel is.

• 대한기계학회논문집
• /
• 제9권1호
• /
• pp.24-30
• /
• 1985

본 연구에서는 풍동을 사용한 모델 실험을 통하여 어긋난 배열을 갖는 파이프 집합체 모델의 고유진동수와 감쇄비를 변화시키면서 3가지 P/D값에서의 불안정 임계속 도를 실험으로 구하였다. 이와 같은 실험은 Connors, Pettigrew Gorman, Weaver & Grover, Tanaka등 많은 사람에 의하여 산발적으로 발표되어 졌으나 본 연구에서는 파 이프 집합체의 P/D값을 바꾸어 가며 넓은 질량―감쇄비 영역에서 체계적으로 실험을 수행하고 그 결과를 비교 분석하였다.