• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집B
• /
• pp.946-951
• /
• 2001

This experimental study is to investigate the intermittent spray characteristics of a pintle nozzle. High speed camera used in this expreiment with 9000fps. The factor, which controls the diesel spray, is the Injection pressure, ambient pressure and ambient temperature. In this paper, experiments were conducted free spray for the ambient pressure(3, 4, 5Mpa), nozzle Injection pressure(10, 14, 18MPa) and ambient temperature(293, 473K). With the higher opening pressure, the spray tip velocity and spray penetration increases while the spray angle decreases, On the other hand, With the higher ambient pressure, the spray angle increase while the spray tip penetration and spray tip velocity decrease. also, With the higher ambient temperature, the spray penetration decrease while the spray angle decrease.

• Journal of Mechanical Science and Technology
• /
• 제14권12호
• /
• pp.1376-1385
• /
• 2000

This study investigates spray characteristics before and after wall impingingment of gasoline spray in suction air flow. For this study, a rectangular model intake port was made of acrylic glass, and suction air was generated by using the forced air blower contrariwise. The injector for this study was a pintle-type port gasoline injector in which an air-assist adaptor is installed to supply assisted air. A PDPA system was employed to simultaneously measure the size and velocity of droplets near the wall. Measured droplets are divided into "pre-impinging droplets"with positive normal velocity and "post-impinging droplets"were negative normal velocity for the suction flow. The velocities, size distributions and Sauter mean diameter(SMD) of pre-and post-impinging droplets for varions injection angles and air-assists are comparatively analyzed.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.112-120
• /
• 2001

Poor fuel vaporization in gasoline engines causes the problem of HC emission during the cold start and warm-up period. This paper presents a strategy to improve fuel atomization during the warm-up phase. In this experiment, the heated fuel-rail system is constructed to investigate the effects of fuel heating on the average size of fuel droplets. The fuel atomization effects are examined by measuring Sauter Mean Diameter (SMD) of the fuel droplets from the three different types (two-hole, pintle, and six-hole) of injectors based upon a returnless heated fuel-rail system. The results show that the six-hole type injector is the most sensitive to fuel heating in terms of SMD among three different types of injectors.

• 한국자동차공학회논문집
• /
• 제8권1호
• /
• pp.10-16
• /
• 2000

Spatially resolved liquid volume fractions from a set of line-of-sight laser diffraction measurements for axisymmetric sprays generated from a pintle-type gasoline injector have been tomographically reconstructed by Abel transformation, Fourier transformation and onion peeling method. Spatially resolved liquid volume fractions classified into 32 size groups were translated characteristics of SI engine fuel sprays. These data were also obtained from the phase Doppler measurements for the same sprays. The comparison between laser deffraction measurements and transformation reconstructs more reasonable spatially resolved characteristics for axisymmetric sprays as well as for asymmetric sprays.

• 오토저널
• /
• 제9권4호
• /
• pp.35-40
• /
• 1987

The experimental study, using constant pressure injection system, is carried out to investigate the effect of the geometrical shape changes of the needle valve of the effective flow area, the spray angle and the Sauter's Mean Diameter according to needle valve lift for a pintle-type injection nozzle. The results are as follows: 1) With the increase of the needle valve lift, the effective flow area is increased, the spray angle is at first increased and later decreased, and the Sauter's Mean Diameter is decreased. 2) It is also shown that the spray angle is maximum at the rapidly increased region of the effective flow area.

• 한국자동차공학회논문집
• /
• 제6권4호
• /
• pp.219-227
• /
• 1998

This paper describes the fuel spray characteristics of gasoline port injectors such as the breakup procedures of liquid fuel, breakup and extinction behaviors of fuel spray at nozzle tip, time history of SMD and velocity distribution of fuel spray in the direction of fuel stream. Pintle-type gasoline fuel injector was used to analyze mentioned spray characteristics. In order to visualize the fuel spray behaviors and to measure the droplet mean diameter and velocities of spray droplets, the Schlieren method, digital image processing and auto-correlation PIV were applied in this study. In addition, the spray characteristics according to the variation of time were considered. The results of fuel spray show that the liquid sheet breakup starts at 10mm downstream actively. The flying time is approximately 4msec between 50mm and 80mm down the nozzle tip. Also, SMD of fuel spray, the number of droplets and fuel velocity distribution at each point of downstream are discussed.

• 한국자동차공학회논문집
• /
• 제5권1호
• /
• pp.146-153
• /
• 1997

An experiment was conducted to figure out the atomization characteristics of a highly viscous biodiesel fuel with rice-barn oil applying and ultrasonic energy into it. A spray simulator for the droplet atomization, an ultrasonic system, and six different nozzles(3 pintle-type nozzles and 3 single hole-type nozzles) were made. To investigate effects of ultrasonic energy in a highly viscous liquid fuel, an immersion liquid method was used as a measurement method on droplet size distributions. It was found that the ultrasonic energy was effective for the atomization improvement of the rice-bran oil as a highly viscous biodiesel fuel and the factor나 such as the nozzle opening pressure, pin-edge angles, hole diameters, and collection distances affected the atomization of spray droplets.

• 한국자동차공학회논문집
• /
• 제3권6호
• /
• pp.134-144
• /
• 1995

The solenoid actuated hydrogen injector and the capacitive peak-hold type driving circuit were designed and made, and the hydrogen supply system for in-cylinder injection was constructed with these. The performance of the injector was investigated through measuring the pintle lift profiles and the injection quantities, and the performance of the hydrogen supply system was confirmed through the experiments at the single cylinder engine. The injection quantity increased linearly as the duration of driving signal increased. At the single cylinder engine, the hydrogen injector was operated stably. The hydrogen flow rate of the injector with the peak-hold type driving circuit could be controlled precisely at high engine speed or low load condition only with the variation of signal duration.

• 한국분무공학회지
• /
• 제4권3호
• /
• pp.15-23
• /
• 1999

The use of LPG as clean fuel for Diesel engine is very attractive way to reduce soot and NOx emission. In this study, a numerical study has been done to know the transient behavior of LPG fuel in chamber pressures which is held at a pressure above (0.37MPa)and below(0.15MPa)the fuel vapor pressure. Results show that the vortex formed within the start of injection at the leading edge of the spray cone and was most apparent for 0.15MPa chamber pressure case. The high speed photographs and model results showed a narrower cone angle during the quasi-steady spray period at the 0.37MPa chamber pressure compared to the 0.15MPa case. And it can be shown that more realistic vaporization process is necessary to predict the spray length well.

• Journal of Ship and Ocean Technology
• /
• 제12권4호
• /
• pp.20-31
• /
• 2008

Development of rudder gap flow blocking device for lift augmentation and cavitation suppression is presented. In order to verify the performance of this device, cavitation visualization and surface pressure measurements were carried out in a cavitation tunnel. Numerical simulations were conducted using a computational fluid dynamics code for more rigorous verification. The new rudder system is equipped with cam devices, which effectively close the gap between the horn/pintle and movable wing parts. The experimental and computational results show that the proposed rudder system is superior to the conventional rudder systems in terms of the lift augmentation and cavitation suppression.