• Journal of Sensor Science and Technology
• /
• v.20 no.1
• /
• pp.14-18
• /
• 2011

An analytical pinning-voltage model of a pinned photodiode has been proposed and derived. The pinning-voltage is calculated using doping profiles based on shallow- and exponential-junction approximations. Therefore, the derived pinning-voltage model is analytically expressed in terms of the process parameters of the implantation. Good agreement between the proposed model and simulated results has been obtained. Consequently, the proposed model can be used to predict the pinning-voltage and related performance of a pinned photodiode in a CMOS active pixel sensor.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1241-1242
• /
• 2006

Electromagnetic properties of $CeO_2$ doped and undoped YBaCuO superconductors were evaluated to investigate the effect of pinning center on the magnetization and magnetic shielding. The variation $\DeltaM$ with doping was maximum for 3% doping and decrease with further doping. The magnetic shielding was evaluated by measuring the induced voltage in secondary coil and the voltage initially set to 0.5V, decreased to 0.17V and 0.28V respectively for the undoped and 3% $CeO_2$ doped sample. The much less change in the induced voltage for the 3% doped sample is attributed to the increased flux shielding by shielding vortex current. The $CeO_2$ was converted to fine $BaCeO_3$ particles which were trapped in YBaCuO superconductor during the reaction sintering. The trapped fine particles, $BaCeO_3$ may be acted as a flux pinning center.

• Electrical & Electronic Materials
• /
• v.10 no.7
• /
• pp.659-667
• /
• 1997

The influence of SiO$_2$on the microstructure and electrical properties of zinc oxide varistor was investigated. Zn$_2$SiO$_4$third phase in the sintered body was found at grain boundaries, multiple grain junctions, and occasionally within ZnO grains. This phase acted as a grain growth inhibitor, which retard the grain growth of the ZnO matrix by impeding migration on the grain boundaries. As SiO$_2$ addition increases, average grain size decreased from 40.6${\mu}{\textrm}{m}$ to 26.9${\mu}{\textrm}{m}$ due to the pinning effect by Zn$_2$SiO$_4$ and drag effect by Si segregation at grain boundaries, the breakdown voltage consequently increased. When SiO$_2$ addition is increased, interface state density decreased, however, the barrier height increased by decrease of donor concentration, as a result, the nonlinear exponent increased and leakage current decreased. While, as SiO$_2$ addition increase, it was found that the apparent dielectric loss factor shows a tendency of decrease. Wholly, electrical properties of zinc oxide varistor can be said to be improved by SiO$_2$addition.

• The Journal of Engineering Research
• /
• v.6 no.2
• /
• pp.33-38
• /
• 2004

To investigate the reliability of the MTJs on the roughness of insulating tunnel barrier, we prepared two MTJs with the different uniformity of barrier thickness. Namely, the one has uniform insulating barrier thickness; the other has non-uniform insulating barrier thickness as compared to different thing. As to depositing amorphous layer CoZrNb under the pinning layer IrMn, we achieved MTJ with uniform barrier thickness. Toinvestigate the reliability of the MTJs dependent on the bottom electrode, time-dependent dielectric breakdown (TDDB) measurements were carried out under constant voltage stress. The Weibull fit of out data shows clearly that $t_{BD}$ scales with the thickness uniformity of MTJs tunnel barrier. Assuming a linear dependence of log($t_{BD}$) on stress voltages, we obtained the lifetime of $10^4$years at a operating voltage of 0.4 V at MTJs comprising CoNbZr layers. This study shows that the reliabilityof new MTJs structure was improved due to the ultra smooth barrier, because the surface roughness of the bottom electrode influenced the uniformity of tunnel barrier.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.2
• /
• pp.339-341
• /
• 2012

The high Tc superconductor of YBCO system with the nominal composition of precursor was prepared from mixed powders of $Y_2O_3$, $BaCO_3$, CuO and $TiO_2$ by the thermal pyrolysis method. The effect of $TiO_2$ doping to Y based ceramics superconductors fabricated by the thermal pyrolysis reaction, to investigate the effect of the dopant on the superconductivity. The voltage appearing across the field-cooled HTS sample increased with external magnetic field. The improvement of critical current property as well as the mechanical property is important for the application. The improvement of the critical current can be achieved by forming the nano size defect working as a flux pining center inside the superconductor. We simply added $TiO_2$ to starting materials to dope $TiO_2$ and observed an increase in the trapped field and the critical current density up to at least 5 wt % $TiO_2$. The $TiO_2$ was converted to fine $BaTiO_3$ particles which were trapped in YBCO matrix during the sintering process. We observed a peak effect of Jc that can be attributed to $TiO_2$ doping and results suggest that introducing a proper amount of pinning centers can significantly enhance current density.

• Journal of the Korean Ceramic Society
• /
• v.33 no.10
• /
• pp.1101-1108
• /
• 1996

No-doped PZT thin films have been fabricated on Pt/Ti/SiO2/Si substrate using Sol-Gel technique. A fast annealing metho (three times of intermediate and final annealing) was used for the preparation of multi-coated 1800$\AA$ thick Nb-doped PZT thin films. As Nb doping percent was increased leakage current was lowered approximately 2 order but dielectic properties were degraded due to the appearance of pyrochlore phase and domain pinning. Futhermore the increase of the final annealing temperature up to 74$0^{\circ}C$lowered the pyrochlore phase content resulting in enhancing the dielectric properties of the Nb doped films. The 3%-Nb doped PZT thin films with 5% excess Pb showed a capacitance density of 24.04 fF/${\mu}{\textrm}{m}$2 a dielectric loss of 0.13 a switchable polarization of 15.84 $\mu$C/cm2 and a coercive field of 32.7 kV/cm respectively. The leakage current density of the film was as low as 1.47$\times$10-7 A/cm2 at the applied voltage of 1.5 V.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1361-1363
• /
• 1997

Zinc oxide-based MOV was fabricated with $SiO_2$ additive ranging from 0.5 to 4.0 mol%, and the microstructure and electrical characteristics were investigated. $Zn_2SiO_4$ phase formed by $SiO_2$ additive was distributed at ZnO grains, grain boundaries, and multiple grain junctions. As the content of $SiO_2$ additive increases, average grain size decreased from 40.6 to $26.9{\mu}m$ due to the Pinning effect by $Zn_2SiO_4$ at grain boundaries Breakdown voltage and nonlinear exponent increased, and leakage current decreased in the range of $11.2{\sim}6.14{\mu}A$ with an increasing $SiO_2$. Donor concentration and interface state density decreased, and barrier height increased in the range of $0.71{\sim}1.04eV$ with an increasing $SiO_2$. While, as the content of $SiO_2$ additive, apparent dielectric constant decreased, peak frequency of dissipation factor decreased in the range of $6.45{\times}10^5{\sim}3.00{\times}10^5Hz$, and dissipation peak was $0.31{\sim}0.22$ at Peak frequency.

• Journal of the Korean Magnetics Society
• /
• v.3 no.4
• /
• pp.269-276
• /
• 1993

Co/Pd multilayered thin films with various ratios of Co sublayers to Pd sublayers(nCo/nPd = 1/4, 2/4, 3/4, 5/4) were fabricated at different substrate temperatures($R.\;T.,\;100,\;150,\;200\;^{\circ}C$) with the conventional vacuum evaporation method, and their Hall voltage hysteresis curves were measured. These Hall curves were decomposed on the basis of the superpose of the transverse Hall effect term from the magnetizations of Co and Pd sublayers and the magnetoresistivity term, by the optimal fitting method. In the results, both of the ferromagnetic and anti ferromagnetic states coexisted through whole samples, and the uniaxial or unidirectional easy axis type Hall hysteresis curves occured were dependent upon the effects of the exchange anisotropy between both magnetic states and the domain wall pinning by the antiferromagnet inclusions.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.7
• /
• pp.782-787
• /
• 2004

Superconducting flux flow transistor (SFFT) is based on a control of the Abrikosov vortex flowing along a channel. The induced voltage by moving of the Abrikosov vortex in an SFFT is greatly affected by the thickness, the width, and the length of channel. In order to fabricate a reproducible channel in the SFFT, we studied the variation of the critical characteristics of ${YBa}_2{Cu}_3{O}_7-\delta(YBCO)$ thin films with the etching time using ICP (Inductively coupled plasma) system. From the simulation, it was certified that the vortex velocity was increased in a low pinning energy at channel width 0,5 mm. The surfaces of YBCO thin film were etched by ICP etching system. We observed the etched channel surfaces by AFM (Atomic Force Microscope) and measured the critical current density with etching time. As a measured results, the etching thickness of channel should be optimized to fabricated a flux flow transistor with specified characteristics.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.12
• /
• pp.56-63
• /
• 1994

The effects of sulfur treatments on the barrier heithts of Schottky contacts and the interface-state density of metal-insulator-semiconductor (MIS) capacitors on InP have been investigated. Schottky contacts were formed by the evaporation of Al, Au, and Pt on n-InP substrate before and after (NH$_{4}$)$_{2}$S$_{x}$ treatments, respectively. The barrier height of InP Schottky contacts was measured by their current-voltage (I-V) and capacitance-voltage (C_V) characteristics. We observed that the barrier heights of Schottky contacks on bare InP were 0.35~0.45 eV nearly independent of the metal work function, which is known to be due to the surface Fermi level pinning. In the case of sulfur-treated Au/InP ar Pt/InP Schottky diodes, However, the barrier heights were not only increased above 0.7 eV but also highly dependent on the metal work function. We have also investigated effects of (NH$_{4}$)$_{2}$S$_{x}$ treatments on the distribution of interface states in Si$_{3}$N$_{4}$InP MIS diodes where Si$_{3}$N$_{4}$ was provided by plasma enhanced chemical vapor deposition (PECVD). The typical value of interface-state density extracted feom 1 MHz C-V curve of sulfur-treated SiN$_{x}$/InP MIS diodes was found to be the order of 5${\times}10^{10}cm^{2}eV^{1}$. This value is much lower than that of MiS diodes made on bare InP surface. It is certain, therefore, that the (NH$_{4}$)$_{2}$S$_{x}$ treatment is a very powerful tool to enhance the barrier heights of Au/n-InP and Pt/n-InP Schottky contacts and to reduce the density of interface states in SiN$_{x}$/InP MIS diode.