• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.736-742
• /
• 2016

Wooden dowels are commonly used to join the wooden members together in many types of structures, But little information is available concerning their holding properties in domestic wood. This study was performed to determine the withdrawal loads and strengths on the effect of diameter of dowel and hole clearance. The test block was manufactured from 15 mm thick korean red pine and korean pine. The dowel was manufactured 6, 8 and 10 mm diameters from korean castanea, korean pine and tuliptree. Research reported here indicates that withdrawal loads increase, but withdrawal strengths decrease, in a linear fashion as the dowel diameter increases. This study also indicates that dowel withholding load and strength increase in a linear fashion as a hole clearance decreases.

• Korean journal of applied entomology
• /
• v.42 no.4
• /
• pp.315-321
• /
• 2003

Larval entrance and adult emergence holes of Japanese pine sawyer (Monochamus alternatus), primary vector of pinewood nematode (Bursaphelenchus xylophilus), were measured in dead pine logs from 1999 to 2002. Their distributions within pine log were also analyzed. More numbers of entrance and emergence holes were distributed on crown than trunk part as 56.2 and 27.7 holes/m$^2$, respectively Higher proportions of entrance (27.5％) and emergence holes (22.4%) were distributed on the log with 8 to 10 cm diameter; the larger or the smaller logs had fewer holes. Surface area of entrance hole was 65.8 $\textrm{mm}^2$ and diameter of emergence holes was 7.0 mm in average. Average depth of pupal chamber was 24.8 mm from surface to the bottom of the chamber, and its volume ranged from 200 to 2.000 ㎣ Average distance between entrance and emergence holes on bark surface was 3.3 cm. Gallery length from the beginning of entrance hole to the end of emergence hole was 46.2 mm.

• Korean journal of applied entomology
• /
• v.56 no.2
• /
• pp.187-193
• /
• 2017

The Japanese pine sawyer, Monochamus alternatus Hope, is a representative vector of the pine wood nematode, Bursaphelenchus xylophilus, which causes wilting symptoms in pine trees. A control method using a net has been introduced, which is an alternative method to the fumigation for the control of dead pine trees by pine wilt disease. This study was carried out to investigate the factors that induce gnawing and escaping behaviors of M. alternatus. The behaviors were examined after M. alternatus adult was placed in a confined space at different temperatures. M. alternatus adults could escape through mesh net torn by gnawing when they were confined in a space of 30 mm or less in diameter. The success rate of escape was high at 20 to $30^{\circ}C$, and no adults escaped at $15^{\circ}C$. The enticement of M. alternatus adults by food didn't affect the success rate of escape. In the case of not being confined in a narrow space, the escaping hole could not be formed because the gnawing was not concentrated on one part. M. alternatus moved its body in a narrow space using the tarsus of middle and hind legs, and made an escape hole by concentrically gnawing the obstacle on the front side with mandible, and showed a behavior of getting out while supporting the body by supporting the front legs. The present results will be able to use as an important basic information for evaluating the performance of mesh net which confines M. alternatus adults and suggested by alternative method to fumigation technology.

• Journal of the Korean Wood Science and Technology
• /
• v.40 no.2
• /
• pp.61-70
• /
• 2012

In this study the effect of heartwood-coating (HCO), vapor-dam (VD), bark-remaing (BR) and bark-remaining- coating (BRC) treatments were evaluated during air circulating oven-drying of hollowed round-post of Korean red pine. Hollowed round-post could be dried from the green condition to approximately 6% MC within 84 to 156 hours for the UC, HCO and VD specimens and it took 72 to 240 hours to about 8% MC, which is recommended as the indoor in-use MC. The temperatures in the hole of the Control (UC) and HCO specimens constantly showed a higher-leveled distribution pattern than those inside wood. The vapor pressure in the hole of the UC, HCO and BR specimens was higher than that inside wood and showed difference as highest value of about 20 mbar. The surface checks of all specimens were mild and were observed in increasing order of BRC, BR, UC, VD and HCO specimens.

• Journal of the Korea Furniture Society
• /
• v.28 no.1
• /
• pp.53-59
• /
• 2017

Wooden dowels are commonly used to join the particleboard members together in many types of structures, But little information is available concerning their holding properties in domestic particleboard. This study was performed to determine the withdrawal loads and strengths on the effect of diameter of dowel and hole clearance. The test block was manufactured from 15 mm thick domestic particleboard. The dowel was manufactured 6, 8 and 10 mm diameters from korean castanea, korean pine and tuliptree. Research reported here indicates that withdrawal loads increase, but withdrawal strengths decrease, as the dowel diameter increases. This study also indicates that dowel withholding load and strength for particleboard less decrease than those for domestic wood as a hole clearance decreases.

• Journal of the Korean Wood Science and Technology
• /
• v.39 no.1
• /
• pp.15-20
• /
• 2011

The pine wilt disease is one of the most serious forest diseases that kill the pine trees, and the study on the invasion and movement of the pine wood nematode within the tree is very important for understanding the inhabitation of pine wood nematode. In this relation, the microscopic observation was carried out to study the place of inhabitation and movement of pine wood nematode within the infested wood. In result, the rays were mainly infested by pine wood nematode and showed dark discoloration due to their necrosis in cross, radial and tangential surface. Also, the intensive damage was found in the resin canals. On the other hand, some traumatic resin canals in tangential band were identified in the sapwood near the cambium. In the ray, the pine wood nematode occurred more commonly in the ray parenchyma cell and fusiform ray with horizontal resin canal than in the ray tracheid and uniseriate ray without horizontal resin canal, respectively. The pine wood nematode was thought to move from ray to tracheid through the large natural opening, window-like pit, in the cross-field, neither through the small natural opening, bordered pit, in the tracheid nor through the tracheid wall by creating a bore hole.

• Journal of the Korean Wood Science and Technology
• /
• v.50 no.1
• /
• pp.1-11
• /
• 2022

To evaluate the bearing strength of red pine cross-laminated timber (CLT) with self-tapping screw (STS), which is widely used as a fastener for connection in CLT building, the bearing test was conducted. Accoring to the STS's diameters (8, 10, 12 mm), the bearing test specimens with half hole were manufactured. Bearing strength was compared and reviewed in consideration of the configuration in STS and the loading direction to the grain of red pine. As a result of the bearing test on the STS's diameter, the yield bearing load increases as the larger diameter of the STS in all directions of the red pine. The bearing strength of the thread part (thread + tip) was higher than the shank part (shank + shank cutter). In compared with the directions to the grain of red pine, the bearing strength of the cross section parallel to the loading direction was the highest, and the tangent section was the lowest bearing strength. The average bearing strength of the loading direction in parallel to the grain was 23.43 MPa, which was about 45% higher than the average 16.16 MPa in perpendicular to the grain. The predicted bearing strength calculated by Eurocode (EN) and Korean Building Code (KBC)'s equation was lower than the experimental value. It is nessesary to propose the new equations of bearing strength reflected the configuration information of STS.

• Journal of the Korean Wood Science and Technology
• /
• v.21 no.1
• /
• pp.39-50
• /
• 1993

The purpose of this study was to describe the micromorphological changes in Korean red pine (Pinus densiflora S. et Z.) wood decayed by a major brown-rot fungus, Lentinus lepideus, using scanning electron microscope and transmission electron microscope. At the end of the 12-week exposure to the fungus in soil block procedure(ASTM 1971), test blocks sustained 5.02% weight loss. The formation of bore hole by hyphae and penetration of hyphae through bordered pit were not observed. Instead, fungal hyphae appeared to penetrate axially tracheid luminar from the the ray cells via cross field pits. Hyphae were mainly found in lignin rich cell corner regions of tracheids, and also extensive degradation of tracheid wall occurred in this region. Extensive degradation of $S_2$ layer occurred without noticeable alteration of the $S_3$ layer, but warty layer and compound middle lamella remained relatively intact. Localized erosion, the characteristic of white rot, was observed in some cell wall and wall components including lignin were found to be decomposed.

• Journal of the Korean Wood Science and Technology
• /
• v.11 no.3
• /
• pp.14-22
• /
• 1983

The purpose of this study was to evaluate the effect of short-term paraquat treatment without insecticides on the enhancement in oleoresin of pitch pine (Pinus rigida M.) at various distances from the wound height. The trees were treated with 0.5, 2 and 4% paraquat solutions using the bore-hole technique. Duplicate cores from treated and untreated sides of treated trees were made at 5 height levels (-0.3, 0.0, 0.3, 0.9 and 1.5 m above the wound height) at 3 months after treatment. The alcohol-benzene extractives based on unextracted oven-dry cores were taken as oleoresin contents. The results were as follows: 1. The effect of oleoresin enhancement at wound height were not affected by paraquat concentration. 2. Ascending distance of the enhancing effects above the wound height was directly related to paraquat concentration. Only in 4% paraquat treated trees, the effect extended to 1.5 m above the wound height. 3. As a result of examining descending distance of the enhancing effects at 0.3 m below the wound height, the effects extended to there in 4% and 2% paraquat treated trees.

• Journal of the Korea Furniture Society
• /
• v.24 no.1
• /
• pp.60-69
• /
• 2013

Timber is an eco-friendly material that is suitable for low carbon and green growth, and recently, studies on utilization and manufacture of timber are increasing. Thus, we need a stable supply of wood working materials for the formative element and widespread function of timber. It is necessary to develop the use of timber because it enhances the added value of this material by making the most of it. In this way, skin-timber is an appropriate material for life articles because skin-timber has a variety of functions including the ability for storage use, the beauty of structure, the ability to maintain heat and insulation, and the capability to control humidity. In this study, I developed household items using skin-timbers that are made up of circular columns and square columns of pine, larch, and yellow popular. The circular and square columns have an inner hole that is approximately 90% of the external structure's width. I intended for the concept of these designs to display creativity considering functionality and productivity. These items are life articles and furniture for modern people. They are eco-friendly products that are varnished with traditional lacquer and natural oil. According to the result of this study, skin-timbers are made of domestic pine, larch, and yellow popular and are resource of furniture, household items, and woodcraft. I believe skin-timber is not only a useful material for processability and design applicability, but it also has the capability to be a multifunctional and high value-added material. Also, if the standards, such as cortex thickness, outside diameter, and length, of skin-timber are producted diversely, I believe skin-timber can be have more the possibility of industrial products' development.