• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.7
• /
• pp.703-714
• /
• 2010

This paper describes the design optimization of a rotating rectangular channel with staggered arrays of pin-fins by Kriging metamodeling technique. Two non-dimensional variables, the ratio of the height to the diameter of the pin-fins and the ratio of the spacing between the pin-fins to the diameter of the pin-fins are chosen as the design variables. The objective function that is a linear combination of heat transfer and friction loss related terms with a weighting factor is selected for the optimization. To construct the Kriging model, objective function values at 20 training points generated by Latin hypercube sampling are evaluated by a three-dimensional Reynolds-averaged Navier-Stokes (RANS) analysis method with the SST turbulence model. The Kriging model predicts the objective function value that agrees well with the value calculated by the RANS analysis at the optimum point. The objective function is reduced by 11% by the optimization of the channel.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.3
• /
• pp.245-251
• /
• 2015

In an electrical reliability test of a printed circuit board (PCB), the impact of the micro probing pins on the PCB needs to be checked to ascertain the quality of the circuit. In this study, the impact of the dynamic movement of the probing pin on the pad was observed. As a misaligned pin can exert horizontal force on the pad of the PCB, this study focused on the behavior of a misaligned probing pin. The parameters of observation were the circular and flat edges of the probing pin. The effects of the speed of movement, diameter, and the length of projection of the probing pin were also investigated. The results demonstrated that slippage angle is strongly affected by the shape of the edge of the probing pin, and that projection length is an important factor affecting pin slippage. In contrast, the speed of movement of the probing pin was able to double the slippage angle.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.9
• /
• pp.1352-1358
• /
• 2004

The mechanical spring is one of widely used machine elements. Among various kinds, flat-type spring loaded by a rotating pin was studied. A flat spring was simplified to a cantilever beam, and numerical analysis was attempted. Since the loading pin rotates about a separate axis from the fixed spring or vice versa, the location, direction, and magnitude of the contact force including normal contact and friction loads vary accordingly. Meanwhile, the spring is deformed substantially as the relative motion progresses. Therefore, this problem needs to be formulated taking the follower loading characteristics and geometrical non-linearity into account. Derived nonlinear differential equation was solved to yield the spring deflection, contact force and the torque to rotate the pin, and the result was compared with a finite element solution. Also, the influences of principal design parameters were studied. The proposed methodology is expected to be useful for the design of pin-loaded flat spring and the prevention of mechanical failures in the form of yielding or fatigue failure of spring or severe wear of the components.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.11a
• /
• pp.1-12
• /
• 2001

In cold forging of piston-pin for automobile parts, the flow defect appears by the dead metal zone. This appearance evidently happens in products with a thin piercing thickness for the dimension accuracy and the decrease of material loss. The best method that can prevent flow defect is removing dead metal zone. The purpose of this study is to investigate the material flow behavior of forward-backward extruded piston-pin through the relative velocity ratio and the stroke control of upper moving punch & container using the flow control forming technique. The finite element simulations are applied to analyse the flow defect, then the results are compared with the plasticine model material experiments. Finally, the model experiment results are in good agreement with the FE simulation ones.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2001.05a
• /
• pp.159-162
• /
• 2001

A combined finite element and experimental study based on the characteristic length method is performed to investigate the strength and behavior of the pin joint in composite control rod. The failure is estimated by the Yamada-Sun and Tsai-Wu criteria on the characteristic curve. The gap elements are used to simulate the contact between the pin and the composite fitting with hole. The accuracy and applicability of the method are validated by the joint tests. All the specimens were failed in the bearing mode in the test and finite element analysis, and good agreement was found between the predicted and test results on the joint strength of composite control rod.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.2
• /
• pp.110-119
• /
• 1992

Crank pin temperatures were measured and analyzed to find out practical method which can predict the engine bearing reliability. The measuring points were determined to be near the MOFT region and far from that by theoretical calculation. The effect of engine running condition, oil temperature, the change of oil circuit into bearing and crankshaft endplay on crank pin temperature were experimentally tested. The result obtained was as following. The crank pin temperature was dependent on oil film thickness and directly influenced by the change of test condition. Also, the length of the crankshaft endplay was confirmed to be critical to connecting rod bearing failure. In conclusion, we found that the measurement method of crank pin temperature can be used for predicting the engine bearing reliability.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1998.06e
• /
• pp.247-250
• /
• 1998

The scattering of plane ultrasonic waves by the nuclear fuel pin of liquid metal reactor in sodium is studied. According to the internal composition in the cladding tube, the fuel pin has three cross sections, i.e. helium gas plenum, sodium-filled section, and fuel insertion section. The scattering spectra for each section of the fuel pin are different. The circumnavigating ultrasonic waves of each section are analyzed by the resonance scattering method. The whispering gallery wave modes are generated in the sodium-filled plenum section and the fuel rod insertion section with a sodium-gap. The circumferential wave modes are propagated in the cladding tube of the helium gas plenum section. The annular gap between the cladding tube and metal uranium pellet rod affects the scattering spectra. The different propagation characteristics can be utilized for the nondestructive method of detecting the unbonded area and measuring the level of the sodium-filled section of the fuel pin.

• Korean Journal of Computational Design and Engineering
• /
• v.16 no.5
• /
• pp.331-343
• /
• 2011

High tibial osteotomy (HTO) is a widely accepted treatment for unicompartmental osteoarthritis of the knee and other lower extremity deformities, particularly for young and active patients. However, it is generally recognized as a technically demanding procedure. Thus the limitations of conventional surgical methods have been reported. Currently, the use of computer-aided surgery (CAS) system for successful surgery was increased. However it has been reported many problems such as expensive equipment, infection or fracture caused by inserting half-pin and delaying surgery. Therefore we propose a novel method which can be tracked by using tracking-pin inserted in arbitrary locations of the femur and tibia, and fluoroscopic images obtained from G-arm of antero-posterior and lateral-medial.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.1 s.14
• /
• pp.33-38
• /
• 2006

The ATE driver to test a high speed semiconductor chip is designed by using general logic drivers instead of dedicated pin drivers. We have proposed a structure of general logic drivers using FPCA and assured its correct operation by EDA tool simulation. PCB circuit was implemented and Altera FPGA chip was programmed using DDR I/O library. On the PCB, it is necessary to place two resistors connected output drivers near to the output pin to adjust an impedance matching. We confirmed that the measured results agree with the simulated values within 5% errors at room temperature for the input signals with 800Mbps data transfer rate and 1.8V operating voltage.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.12 no.4
• /
• pp.325-334
• /
• 1987

Microwave integrated circuit phase shifters have undergone remarkable development to satisfy the fast and precise phase control requirements for phased array antennas. It is shown how relection type phase shift circuits using PIN diode can be analyzed and implemented so as to derve design equations for any phase shift. The reflection properties are achieved by the use of an impedance transforming two-port network and the virtual matching impedance method. Experimental and theoretical performance of 2-bit hybrid phase shifter designed by this method are found to be in good agreement for each bit.