• 한국전기전자재료학회논문지
• /
• 제20권4호
• /
• pp.332-336
• /
• 2007

In this study, multilayer piezoelectric transformer was manufactured using the PMN-PNN-PZT ceramic and then the electrical characteristics were investigated according to the variations of frequency and load resistance. The voltage step-up ratio of multilayer piezoelectric transformer showed the maximum value at the vicinity of 75 kHz and increased according to the increase of load resistance. When the output impedance coincided with the load resistance, the multilayer piezoelectric transformer showed the temperature rise of less than $20^{\circ}C$ at the output power of 20 W. As the results, the multilayer piezoelectric transformer manufactured at low co-firing temperature of $940^{\circ}C$ using PMN-PNN-PZT ceramics could be stably driven as the step-down transformers.

• 한국정보통신학회논문지
• /
• 제15권11호
• /
• pp.2457-2464
• /
• 2011

본 논문에서는 압전 소자를 이용한 진동에너지 하베스팅 회로를 설계하였다. 압전소자의 전력-전압 특성을 이용하여 최대 전력을 부하로 전달하기 위한 MPPT(Maximum Power Point Tracking) 제어 기능을 구현하였다. MPPT 제어 회로는 압전소자의 출력 단에 연결된 전파 정류회로의 개방회로 전압을 주기적으로 샘플링하여 최대 가용전력이 생성되는 지점을 추적하고 이를 부하로 전달하는 역할을 한다. 제안된 진동에너지 하베스팅 회로는 $0.18{\mu}m$ CMOS 공정으로 설계하였다. 모의실험 결과 설계된 회로의 최대 전력 효율은 91%이고, pad를 제외한 칩 면적은 $700{\mu}m{\times}730{\mu}m$이다.

• 센서학회지
• /
• 제19권3호
• /
• pp.209-213
• /
• 2010

This paper describes the fabrication and characteristics of AlN piezoelectric MPG(micro power generator). The micro energy harvester was fabricated to convert ambient vibration energy to electrical power as a AlN piezoelectric cantilever with Si proof-mass. To be compatible with CMOS process, AlN thin film was grown at low temperature by RF magnetron sputtering and micro power generators were fabricated by MEMS technologies. X-ray diffraction pattern proved that the grown AlN film had highly(002) orientation with low value of FWHM(full width at the half maximum, $\theta=0.276^{\circ}$) in the rocking curve around(002) reflections. The implemented harvester showed the $198.5\;{\mu}m$ highest membrane displacement and generated 6.4 nW of electrical power to $80\;k{\Omega}$ resistive load with $22.6\;mV_{rms}$ voltage from 1.0 G acceleration at its resonant frequency of 389 Hz. From these results, the AlN piezoelectric MPG will be possible to suitable with the batch process and confirm the possibility for power supply in portable, mobile and wearable microsystems.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 연구회
• /
• pp.135-139
• /
• 2001

Contour vibration mode piezoelectric transformers were designed and fabricated to the square plate with size of $27.5{\times}27.5{\times}2.5(2.6,\;3.0)mm^3$ using PNW-PMN-PZT ceramics. Electrical characteristics of the piezoelectric transformer were investigated for fluorescent lamp ballast application. The electrical properties and characteristic temperature rise were measured using oscilloscope and infrared temperature sensor. A 28W fluorescent lamp was successfully driven by the fabricated transformers. After driving the lamp using Power Amplifier for 24 min, the output power, efficiency and characteristic temperature rise of PT2 piezoelectric transformer showed the appropriate values of 28.01 W, 99.43% and $11^{\circ}C$, respectively. The electronic ballast using PT2 piezoelectric transformer showed an excellent output power of 28.85 W and efficiency of 86.3%, respetively.

• 한국소음진동공학회논문집
• /
• 제20권4호
• /
• pp.397-404
• /
• 2010

The use of equivalent circuit models of piezoelectric energy harvesters is inevitable when power circuitry including rectifying and smoothing circuit elements is connected to them for evaluating DC electrical outputs. This is because it is difficult to incorporate the electro-mechanical coupling resulting from the additional circuitry into the conventional finite element analysis. Motivated by this observation, we propose a method to accurately extract the equivalent circuit parameters by using commercially available FEM software such as ANSYS which provides three-dimensional AC piezoelectric analysis. Then the equivalent circuit can be analyzed by circuit simulators such as $SimPowerSystems^{TM}$ of MATLAB. While the previous works have estimated the circuit parameters by experimental measurements or by analytical solutions developed only for limited geometries and boundary conditions, the proposed method has no such limitation because piezoelectric energy harvesters of any shapes and boundary conditions can be treated in FEM software. For the verification of the proposed method, multi-modal AC electrical power output by using a corresponding equivalent circuit is compared with that by ANSYS. The proposed method is then shown to be very useful in the subsequent evaluation of DC electrical output which is obtained by attaching a bridge diode and a storage capacitor to a piezoelectric energy harvester.

• 세라미스트
• /
• 제22권1호
• /
• pp.56-69
• /
• 2019

Recent advances in low-power sensors and transmitters are driving the search for standalone power sources that utilize unused ambient energy. These energy harvesters can alleviate the issues related to the installation and maintenance of sensors. Particularly piezoelectric energy harvesters, with the ability to convert ambient mechanical energy into useful electricity, have received significant attention due to their high energy density, low cost and operational stability over wide temperature and pressure conditions. In order to maximize the generated electrical power, the natural frequency of the piezoelectric energy harvester should be matched with the dominant frequency of ambient vibrations. However, piezoelectric energy harvesters typically exhibit a narrow bandwidth, thus, it becomes difficult to operate near resonance under broadband ambient vibration conditions. Therefore, the resonating of energy harvesters is critical to generate maximum output power under ambient vibration conditions. For this, energy harvesters should have broadband natural frequency or actively tunable natural frequency with ambient vibrations. Here, we review the most plausible broadband energy harvesting techniques of the multi-resonance, nonlinearity, and self-resonance tuning. The operation mechanisms and recent representative studies of each technique are introduced and the advantages and disadvantages of each method are discussed. In addition, we look into the future research direction for the broadband energy harvester.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.277-277
• /
• 2009

In this paper, PMPG (Piezoelectric Micro Power Generator) was investigated by ANSYS FEA (Finite Element Analysis) to decrease operating frequency and improve out power. The micro power generator was designed to convert ambient vibration energy to electrical power as a ZnO piezoelectric material. To find optimal model in low vibration ambient, the shape of power generator was changed with different membrane width, thickness, length, and proof mass size. Used the ANSYS modal analysis, bending mode and stress distribution of optimal model were analyzed. Also, the displacement with the frequency range was analyzed by harmonic analysis. From the simulation results, the resonance frequency of optimal model is about 373 Hz and confirmed the possibility of ZnO micro power generator for wireless sensor node applications.

• 센서학회지
• /
• 제18권5호
• /
• pp.372-376
• /
• 2009

This paper describes the characteristics of piezoelectric micro power generators by the ANSYS FEA(finite element analysis). The micro power generator was designed to convert ambient vibration energy to electrical power as a ZnO piezoelectric material. To find optimal model in low vibration ambient, the shape of power generator was changed with different membrane width, thickness, length, and proof mass size. Using the ANSYS modal analysis, bending mode and stress distribution of optimal model were analyzed. Moreover, the displacement with the frequency range was analyzed by harmonic analysis. From the simulation results, the resonance frequency of optimal model is about 373 Hz and investigate the possibility of ZnO micro power generator for ambient vibration applications.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.297.2-297.2
• /
• 2013

Scavenging electricity from wasteful energy resources is currently an important issue and piezoelectric nanogenerators (NGs) based on zinc oxide (ZnO) are promising energy harvesters that can be adapted to various portable, wearable, self-powered electronic devices. Although ZnO has several advantages for NGs, the piezoelectric semiconductor material ZnO generate an intrinsic piezoelectric potential of a few volts as a result of its mechanical deformation. As grown, ZnO is usually n-type, a property that was historically ascribed to native defects. Oxygen vacancies (Vo) that work as donors exist in ZnO thin film and usually screen some parts of the piezoelectric potential. Consequently, the ZnO NGs' piezoelectric power cannot reach to its theoretical value, and thus decreasing the effect from Vo is essential. In the present study, c-axis oriented insulator-like sputtered ZnO thin films were grown in various temperatures to fabricate an optimized nanogenerator (NGs). The purity and crystalinity of ZnO were investigated with photoluminescence (PL). Moreover, by introducing a p-type polymer usually used in organic solar cell, it was discussed how piezoelectric passivation effect works in ZnO thin films having different types of defects. Prepared ZnO thin films have both Zn vacancies (accepter like) and oxygen vacancies (donor like). It generates output voltage 20 time lager than n-type dominant semiconducting ZnO thin film without p-type polymer conjugating. The enhancement is due to the internal accepter like point defects, zinc vacancies (VZn). When the more VZn concentration increases, the more chances to prevent piezoelectric potential screening effects are occurred, consequently, the output voltage is enhanced. Moreover, by passivating remained effective oxygen vacancies by p-type polymers, we demonstrated further power enhancement.

• 제어로봇시스템학회논문지
• /
• 제15권12호
• /
• pp.1197-1202
• /
• 2009

We present a power-efficient driving scheme that consists of piezoelectric actuator and driver IC for AF (Auto-Focus) on ISM (Image Sensor Module). The piezoelectric actuator is more power-efficient than conventional voice coil motor actuator. And high power-efficiency driver IC is designed. So the proposed driving scheme using designed piezoelectric actuator and driver IC is more close to recent trend of green IT. The diver IC should guarantee fast and accurate performance. So, the optimum driving method and high accurate frequency synthesizer are proposed. The die area of designed driver IC is $2.0{\times}1.6mm^2$ and power consumption is 2.8mW.