• 한국강구조학회 논문집
• /
• 제22권5호
• /
• pp.411-420
• /
• 2010

교량은 주행차량에 의하여 지속적이며 반복적인 변형에너지가 발생하며, 이러한 교량의 변형에너지를 압전소자를 이용하여 전기에너지로 변환 할 수 있다. 하지만 압전소자를 구조물에 부착하여 구조물의 운동에너지를 전기에너지로 변환하여 사용하기 위해서는 구조물에 작용하는 하중 및 하중에 따라 압전소자에서 발생하는 변형률 관계 등이 제시되어야 압전소자를 합리적으로 적용할 수 있는 가능성을 평가할 수 있다. 따라서 본 연구에서는 압전소자를 교량 구조물에 적용하였을 때 발생하는 전압을 평가하기 위하여 강교량을 모사한 강합성 거더 교량 실험체를 제작하고 교량의 하중효과 등을 고려한 하중을 재하하고 이에 따라 압전소자에서 발생되는 전압을 평가하고 압전전압의 제안식과 실험결과를 비교하였다.

• 한국전기전자재료학회논문지
• /
• 제21권6호
• /
• pp.556-561
• /
• 2008

This paper reports the characteristics of piezoelectric microspeakers that are audible in open air with high quality piezoelectric AlN thin film according to the materials properties. When we use a tensile-stressed silicon nitride diaphragm as a supporting layer, the Sound Pressure Level (SPL) is relatively small and constant at low frequency region and shows about 70 dB at 10 kHz. However, in case of a compressively stressed composite diaphragm, the SPL of the fabricated microspeakers shows higher output pressure than those of a tensile-stressed diaphragm. It produces more than 66 dB from 100 Hz to 15 kHz and the highest SPL is about 100 dB at 9.3 kHz with $20V_{peak-to-peak}$, sinusoidal input biases and at 10 mm distances from the fabricated microspeakers to the reference microphone. From the experimental results, it is superior to have a compressively composite diaphragm in order to produce a high SPL in piezoelectric microspeaker.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 추계학술대회 논문집 Vol.15
• /
• pp.79-82
• /
• 2002

In this paper, a single phase driven piezoelectric motor design was presented for linear motion. Two metal/ceramic composite actuators, a piezoelectric ring which was bonded to a metal endcap from one side, were used as the active elements of this motor. The motor was composed of a piezoelectric ceramic, a metal ring which has 4 arms, and a guider. Motors with 30.0[mm] and 35.0[mm] diameter were studied by finite element analysis and experiments. As results, the maximum speed of motor was obtained at resonant frequency. When the applied voltage of the motor increased, the speed was increased. Also, bidirectional motion of the motor was achieved by combining two motors which have different resonant frequency.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권10호
• /
• pp.1053-1059
• /
• 1996

The pulse-echo response of the piezoceramics PZT-polymer 3-3 type composite transducers with various PVA additions were investigated. The PZT powder was prepared by the molten salt synthesis method. The porous PZT specimens will be used as a filler to make 3-3 type comosite were prepared from a mixture of PZT and polyvinylalcohol(PVA) sphere by utilizing BURPS(Bumout Plastic Sphere) technique. It was shown that the transmitting and receiving sensitivity of 3-3 type piezoelectric composite transducers could be improved than that of solid PZT transducers. The reason is that 3-3 type piezoelectric composite have low dielectric constant, density and acoustic impedance. The distance between transducer and reflector was in good agreement with the distance calculated from the longitudinal velocity of the specimens and receiving time observed pulse-echo responses on the ultrasonic transducer analyzer.

• 한국전산구조공학회논문집
• /
• 제28권5호
• /
• pp.497-502
• /
• 2015

본 논문에서는 굽힘하중이 가해지는 스마트 복합재 적층판의 자유단에서 발생하는 박리응력을 압전 작동기를 이용해서 감소시키는 방법을 응력함수를 이용해 해석하는 방법을 제안하였다. 전기-기계 연성에 의해 나타나는 지배방정식은 최소 보족일의 원리를 이용해 구하였다. 응력상태는 일반적인 고유치 해석과정을 통해 구하였다. 스마트 복합재 적층판의 자유단 박리응력은 압전 작동기를 이용해 감소시킬 수 있었다. cross-ply 복합재 적층판의 박리응력 감소가 angle-ply 복합재 적층판 보다 크게 나타났다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제45회 하계 정기학술대회 초록집
• /
• pp.256-256
• /
• 2013

Carbon nanotubes (CNT) / polyvinylidene fluoride (PVDF) piezoelectric composite films for nanogenerator devices were fabricated by spray coating method. When the CNT/PVDF mixture solution passes through the spray nozzle with small diameter by the compressed nitrogen gas, electric charges are generated in the liquid by a triboelectric effect. Then randomly distributed ${\beta}$ phase PVDF film could be re-oriented by the electric field resulting from the accumulated electrical charges, and might be resulted in extremely one-directionally aligned ${\beta}$ phase PVDF film without additional electric field for poling. X-ray diffraction patterns were used to investigate crystal structure of the CNT/PVDF composite films. It was confirmed that they revealed extremely large portion of the ${\beta}$ phase PVDF crystalline in the film. Therefore we could obtain the poled CNT/PVDF piezoelectric composite films by the spray coating method without additional poling process. Charge accumulation and resulting electric field generation mechanism by spray coating method were shown in Fig. 1. The capacitance of the CNT/PVDF films increased by adding CNTs into the PVDF matrix, and finally saturated. However, the I-V curves didn't show any saturation effect in the CNT concentration range of 0~4 wt%. Therefore we can control the performance of the devices fabricated from the CNT/PVDF composite film by adjusting the current level resulted from the CNT concentration with the uniform capacitance value.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1392-1393
• /
• 2006

In this paper dielectric and piezoelectric properties were measured for 2 phase - dispersed composite system consisting of ferroelectric ceramic PZT particles and polymer PVC. The results were analyzed and the validity of composite theories for experimental results were discussed. And also in high temperature where ionic conductivity is dominated, linear and nonlinear permittivites were measured and discussed.

• Steel and Composite Structures
• /
• 제27권4호
• /
• pp.479-493
• /
• 2018

In this paper nonlocal free vibration analysis of a doubly curved piezoelectric nano shell is studied. First order shear deformation theory and nonlocal elasticity theory is employed to derive governing equations of motion based on Hamilton's principle. The doubly curved piezoelectric nano shell is resting on Pasternak's foundation. A parametric study is presented to investigate the influence of significant parameters such as nonlocal parameter, two radii of curvature, and ratio of radius to thickness on the fundamental frequency of doubly curved piezoelectric nano shell.

• Structural Engineering and Mechanics
• /
• 제68권2호
• /
• pp.203-213
• /
• 2018

This paper presents a study of geometric nonlinear forced vibration of carbon nano-tubes (CNTs) reinforcement composite plates on nonlinear elastic foundations. The plate is bonded with piezoelectric layers. The von Karman geometric nonlinearity assumptions with classical plate theory are employed to obtain the governing equations. The Galerkin and homotopy perturbation method (HPM) are utilized to investigate the effect of carbon nano-tubes volume fractions, large amplitude vibrations, elastic foundation parameters, piezoelectric applied voltage on frequency ratio and primary resonance. The results indicate that the carbon nano-tube volume fraction, applied voltage and elastic foundation parameters have significant effect on the hardening response of carbon nanotubes reinforced composite (CNTRC) plates.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 하계종합학술대회 논문집
• /
• pp.349-352
• /
• 1989

Poling piezoelectric ceramic-polymer composites with 0-3connectivity is difficult because of the high dielectric constant of most of the ferroelectric filler materials, and the high resistivity of the polymer matrix. To aid in poling this type of composite, conductivity of the polymer phase can be controlled by adding small amount of a semiconductor phase such as germanium, carbon or silicon. In this study, flexible piezoelectric composites of $PbTiO_3$ powder and Eccogel polymer were developed using small amounts of a semiconducting phase. These composites were poled rapidly at low voltages, resulting in properties superior to composites prepared without a conductive phase. The effect of addition of various conductive phase with different volume percentage on the dielectric and piezoelectric properties of the composite are discussed here.