• Journal of Forest and Environmental Science
• /
• 제37권1호
• /
• pp.79-89
• /
• 2021

Cement bonded boards of 10 mm in thickness were produced from the mixture of Gmelina arborea sawdust and corn cob particles. The strength and dimensional stability of cement bonded composites produced from these two mixtures were examined. A total of thirty experimental boards were produced at density level of 1,000 kg/㎥ with cement to fibre ratio of 2.5:1 and 3:1 and five (5) blending proportions of G. arborea sawdust to corn cob particles of 100:0; 75:25; 50:50; 25:75 and 100:0. The effect of the cement to fibre ratio and blending proportion on the Water Absorption (WA), Thickness Swelling (TS), Modulus of Rupture (MOR), and Modulus of Elasticity (MOE) were determined. The result indicates that as the mixing ratio of cement to fibre and blending proportion of maize cob (75%) to G. arborea (25%) increased, the thickness swelling, water absorption decreased, whereas the MOR and MOE increased. It also shows that most dimensionally stable and flexural strength boards were produced at the highest level of mixing ratios (3:1) and blending proportion of G. arborea to corn cob 25:75. However, the analysis of variance shows that TS and WA were significantly different, whereas, MOE and MOR were not significantly affected by mixing ratios and blending proportions. Finding of this study has shown that maize cob particles are suitable for cement bonded board production.

• Polymer(Korea)
• /
• 제39권1호
• /
• pp.114-121
• /
• 2015

Mutli-walled carbon nanotubes (MWCNTs) were surface-modified by a hydrofluoric acid solution to remove impurities and improve interfacial bonding and dispersion of nanotubes in an epoxy matrix. The crystallinity on the surface of treated MWCNTs was investigated by X-ray photoelectron spectroscopy and Raman spectroscopy. The mechanical properties were characterized by tensile test, and the enhancement of mechanical properties of the modified MWCNTs/epoxy composites was indicated by a 33% increase in tensile strength. The electromagnetic interference shielding effectiveness (EMI-SE) of modified MWCNTs/epoxy composites was improved with an increase in concentration of hydrofluoric solution, and EMI-SE showed the maximum increase with 25% HF. However, mechanical and EMI-SE properties didn't show further increase with over 50% HF concentration because the properties of MWCNTs were influenced by degradation of crystallinity and intrinsic properties of MWCNTs. The mechanical and electrical property enhancements of the polymer composites are attributed to the modification of MWCNTs which improve crystallinity of MWCNTs and dispersion in the epoxy resin.

• Journal of the Microelectronics and Packaging Society
• /
• 제29권4호
• /
• pp.9-14
• /
• 2022

Silica aerogel is a porous material with a very low density and high specific surface area. Still, its application is limited due to its weak mechanical properties due to structural features. To solve this problem, a method of complexing it with various polymers has been proposed. We synthesized polyimide cross-linked silica aerogel by the sol-gel process to obtain high mechanical properties. Tetraethyl orthosilicate (TEOS) was used as a precursor to make silica aerogel, and 3- aminopropyltriethoxysilane (APTES) was used as a coupling agent for cross-linking polyimide. Polyimide was synthesized using pyromellitic dianhydride and 3,5-diaminobenzoic acid, and mechanical properties were improved by crosslinking polyimide with 10 repeating units in the polyimide chain using the reaction formula ${\frac{n_1}{n_2}}={\frac{n}{n+1}}$ To realize silica aerogel, polyimide having various weight ratios was added before gelation, resulting in a 19-fold or greater increase in maximum compressive strength compared to pure silica aerogel. From this study, an enhancement of silica aerogel could be enhanced through polymer cross-linking bonds.

• Journal of the Korean Society of Food Science and Nutrition
• /
• 제39권4호
• /
• pp.542-547
• /
• 2010

Physico-chemical properties of starches from potato cultivars with different colors were investigated. White Atlantic potato had 10% higher starch yield than violet Bora Valley potato. It turned out that the shape and structure of Atlantic and Bora Valley potato starch were the same by mechanical analysis using X-ray and SEM. The ratio of $50\;{\mu}m$ particle in starches from Atlantic and Bora Valley potato was $45.44\pm2.79%$ and $42.37\pm1.03%$ respectively. The particle size of Atlantic potato starch was less than that of Bora Valley; however, there was no significant difference (p<0.05). As for moisture coupling, there was no difference (p<0.05) between the two potatoes. Swelling power showed a high increase from $65^{\circ}C$ to $80^{\circ}C$. The swelling power of Atlantic starch was higher by about 0.3% than that of Bora Valley at $90^{\circ}C$. Since Atlantic has smaller starch particles than Bora Valley, more starch particles are contained in the same size, and hence a difference in swelling power. As a result of measuring the gelatinization of potato starches from Atlantic and Bora Valley, a higher gelatinization start, climax, and complete temperatures occurred at Bora Valley than Atlantic. As for gelatinization enthalpy, Bora Valley starch with a higher gelatinization temperature consumed more energy for gelatinization.

• Korean Journal of Food Science and Technology
• /
• 제27권3호
• /
• pp.404-413
• /
• 1995

System parameters (extrusion temperature, extrusion pressure, specific mechanical energy, mean residence time) were analysed on three different screw configurations during twin-screw extrusion of wheat bran. Experiments were conducted over a screw speed of $280{\sim}380\;rpm$, feed rate of $22{\sim}38\;kg/hr$ and moisture content of $17{\sim}33%$ using screws assembled with 3, 4, and 5 reverse screw elements (RSE) adjacent to the heating zone of the barrel. Extrusion temperature increased with increasing RSE but it decreased with increasing feed rate and moisture content. Decreasing the filling ratio of the screw resulted in a lower extrusion pressure, and increasing the length of the RSE gave similar results due to the higher temperature and lower viscosity of melted dough. It was also observed that increasing the feed rate and decreasing moisture content resulted in the reduced extrusion pressure. Specific mechanical energy (SME) decreased when the feed rate and moisture content increased, and SME increased when using RSE posses from 3 to 5. Screw configuration posses with 4 RSE yielded the longest RT, and the smaller the die hole, the higher the RT. In contrast, RT decreased when the feed rate increased. With increasing moisture content RT for 3 RSE increased, but that for 4 and 5 RSE decreased.

• The Journal of Engineering Geology
• /
• 제24권2호
• /
• pp.161-169
• /
• 2014

We present the results of an experimental physical weathering study that focuses on fresh and slightly weathered gneiss samples from the Wonju area of Korea. The study investigated changes in the physico-mechanical properties of these samples during accelerated laboratory-based weathering, including analyses of microfracture formation. The deteriorated samples used in the study were subjected to 100-150 freeze-thaw cycles, with index properties and microfracture geometries measured between each cycle. Each complete freeze-thaw cycle lasted 24 hours, and consisted of 2 hours of saturation in a vacuum chamber, 8 hours of freezing at $-21^{\circ}C{\pm}1^{\circ}C$, and 14 hours of thawing at room temperature. Specific gravity and seismic velocity values were negatively correlated with the number of freeze-thaw cycles, whereas absorption values tended to increase. The amount of deterioration of the rock samples was dependent on the degree of weathering of the rock prior to the start of the analysis. Absorption, specific gravity, and seismic velocity values can be used to infer the amount of physical weathering experienced by a gneiss in the study area. The sizes and density of microfracture in the rock specimens varied with the number of freeze-thaw cycles. We found that box fractal dimensions can be used to quantify the formation and propagation of microfracture in the samples. In addition, these box fractal dimensions can be used as a weathering index for the mid-and long-term prediction of rock weathering. The present results indicate that accelerated-weathering analysis can provide a detailed overview of the weathering characteristics of deteriorated rocks.

• Journal of the Korean Wood Science and Technology
• /
• 제35권2호
• /
• pp.29-38
• /
• 2007

This study was undertaken to investigate the variation of equilibrium moisture content (EMC) in transverse direction and three different directional (longitudinal, radial, and tangential) linear movements, and diffusion coefficients within a tree disc of Korean red pine (pinus densiflora). The EMC gradually increased in heartwood from pith. Therefore, the chemical components might differ even in heartwood and the radial variation in EMC might have a close relationship with the cellulose content within a cross section. The specific gravity increases gradually from pith and the porosity has not direct influence on the variation of EMC within a tree disk. Both the radial and tangential diffusion coefficients exhibited clear trend of increase from pith. The EMC change (${\Delta}EMC$) and tangential diffusion coefficient were close to be axisymmetrical but others were deviated from axisymmetry. The diffusion coefficient decreases with decreasing an activation energy and specific gravity, The diffusion coefficient increased with increasing ${\Delta}EMC$ and hygroscopicity of wood might be inversely proportional to the activation energy, The fJEMC may depend on the chemical constituents of cellulose, hemicellulose and lignin. As the number of sorption sites and sorption capacity of wood increase, therefore, it might be assumed that the hygroscopicity of wood increases while activation energy decreases. Modeling physico-mechanical behavior of wood, the variations should be considered to improve the accuracy.

• Journal of the Korean Vacuum Society
• /
• 제16권1호
• /
• pp.74-78
• /
• 2007

Much interests has been drawn for noble micro-engineering processes for the continuous size reduction on bulk materials from the field of micro-electronics with much downsized IC chips. A traditional microprocessing based on mechanical blade as well as a relatively long pulsed laser usually influence the physico-chemical properties of intact materials when the techniques are applied to process materials with a spatial resolution less than 10 microns. Meanwhile, ultrafast laser pulses are known to exhibit a very small heat-affect zone(HAE) compared to the traditional laser processing and to be applicable for the new functional materials with high performance in optical and electrical properties. In this report, we will review in brief the recent research works on the enhancement of micro-cutting speed of thin silicon wafer as well as the formation of Ge nanostructures based on ultrafast laser pulses.

• Journal of the Korean Wood Science and Technology
• /
• 제43권3호
• /
• pp.334-343
• /
• 2015

This study was carried out to evaluate quantitatively some properties (density, equilibrium moisture content, shrinkage, water vapor adsorption, water absorptivity, compressive strength, bending strength, hardness and decay resistance) of Larix kaempferi lumber which was heat-treated by hot air and has been used commercially in Korea. Equilibrium moisture content of the heat-treated wood was decreased with increase of hydrophobicity. Dimensional stability of the wood was improved with decrease of shrinkage, water vapor adsorption and free water absorptivity. Also, with the thermo-chemical changes of wood component and lower equilibrium moisture content, decay resistance and compressive strength of heat-treated wood were increased. But, bending strength and hardness of wood were decreased.

• Journal of Korean Tunnelling and Underground Space Association
• /
• 제13권3호
• /
• pp.243-260
• /
• 2011

To predict TBM performance in design stage is indispensable for its successful application. The NTNU model, one of the representative TBM performance prediction models uses two distinct parameters such as DRI and CLI obtained from three different tests on bored rock cores. Based on DRI and CLI, it is possible to predict TBM advance rate and cutter life in the NTNU model. In this study, NTNU testing methods and their related testing equipments were introduced to measure DRl and CLI for the NTNU model. Then, in order to derive their relationships, the two key parameters measured for 39 domestic rocks were compared with physico-mechanical properties of rock such as uniaxial compressive strength and quartz content. Lastly, the experimental results were also compared with NTNU database to verify their reliability.