• Korean Chemical Engineering Research
• /
• v.47 no.1
• /
• pp.31-37
• /
• 2009

A zwitterionic surfactant shows not only detergency but also mildness effect since it shows characteristics of a nonionic or an anionic surfactant above an isoelectric point, while showing characteristics of a cationic surfactant below an isoelectric point. Therefore, a zwitterionic surfactant can serve as a dual function surfactant by a single molecule through the interconversion of cleaning and softening effects depending on pH variations of the aqueous solution. In this study, physical properties of betaine surfactant such as CMC, surface tension, interfacial tension, contact angle and viscosity were measured and phase behavior study was performed. Also dual function characteristics of betaine zwitterionic surfactant were investigated by measuring an isoelectric point using QCM(quartz crystal microbalance) and zeta potential measurement. The CMC of betaine surfactant was near $10^{-4}mol/L$ and the surface tension at CMC was about 32 mN/m. The interfacial tension between 1 wt% aqueous solution and n-decane measured by spinning drop tensiometer at pH 2~10 resulted in an increase in interfacial tension until pH 5 and a decrease with pH after 5 and equilibration time showed the similar trend with an increase in pH. The isoelectric point of betaine surfactant measured by QCM experiment was found to exist between 3.0 and 3.3, which is the same as the result determined by zeta potential measurement.

• Journal of the Korean Applied Science and Technology
• /
• v.38 no.1
• /
• pp.19-28
• /
• 2021

Corrosion is the degradation of metals by reaction with the environment. It is difficult to completely remove. Corrosion proceeds rapidly after the protective barrier is destroyed, and several reactions occur that alter the composition and properties of the metal surface and local environments, such as diffusion of metal cations into the matrix, the formation of oxides, and local pH changes. The study of corrosion of steel and iron is of theoretical and practical interest and is receiving considerable attention. Acid solutions, which are widely used in industrial pickling, acid descaling, cleaning and acidification of oil wells, require the use of corrosion inhibitors to suppress corrosion attacks on metallic materials. Physical removal of rust requires expensive special equipment, and chemical removal of it can cause corrosion or shorten the life of the metal. In this study, an eco-friendly rust cleaner was developed using cosmetics and food materials by applying the concept of perm reducing agent and chelate, and applied to remove rust from industrial and hot water pipes and various industrial devices. As a result, it was found that rust cleaners remove rust more effectively and safely compared to conventional treatment methods. At the same time, the rust removal efficiency was 1.75 to 2.5 times better for industrial piping and 1.56 to 2.2 times better for boiler hot water than conventional methods.

• Journal of Korean Academy of Nursing
• /
• v.28 no.3
• /
• pp.705-717
• /
• 1998

Ostomates have suffered from many difficulties due to their physical, psychosocial handicaps and changes of life style to include ostoma management that influences their daily and quality of life. An appropriate nursing education for ostoma management is very important. Practical educational materials needs revision because those were developed by pharmaceutical companies and hospital institutions. The purpose of this study is to provide more practical and reasonable education materials for ostomates by doing analysis and survey of educational materials now being used. We surveyed 8 types of educational materials used in 23 university hospitals and medical centers in Seoul ; four of them were developed by department of nursing and the remainder by an Ostomy Company Data, collected from July 14, 1997 through July 31, 1997 were analyzed. The results are as follows ; 1. The analysis of education guide, on ostomate included 14 subcategories : introduction, structure and function of gastrointestinal tracts, definition of stoma, types of ostomy, definition of peristalsis, methods of defecation management, selection of instrument, resolution of problems and general situations following surgery, daily life, where to ask for help, explanations for terms, information about where to buy instrument, explanations for enterostomal therapist, a matter of consultation with doctor, etc. 2. Introduction contained specific contents on practical ostomate management that ostomates would experience through their lives. Ostomate education guides were developed 3 hospitals except one which missed this point. 3. Most ostomate education guides, except one hospital, helped ostomates to understand their physical structure changes with specific explanations on gastrointestinal tracts with figures. 4. Six institutions did not talk about the definition of peristalsis. 5. All institutions, except two, helped ostomates to understand types of ostomy with figures. 6. More detailed explanations on natural defecation are needed. The benefits and pitfalls of natural defecation should be more specified. 7 No psychosocial difficulties of ostomy management were addressed. 8. The efficiency of enema can be better understood through all explanations with figures. Some institutions did not mention items about definition, benefits, pitfalls of enema, sequency of enema, how to wash, cautions performing and enema, skin management, cleaning instrument after enema proper time to spend. 9. There were no detailed contents and what to do in case of not being able to do enema. 10. Only one educational material mentioned emotional aspects after the surgrey. 11. Most institutions explained subcategory of daily life but did not provide specific contents on the difficulties of physical, psychological, and sociocultural controls. 12. The subcategory of ureterostomy education guides included explanations on normal structure and function of urinary tracts, types of ureterostomy, how to manage skin, usage and types of instrument, commercial urostomy, how to manage instrument, daily life, introduced the general contents. However, more specific explanations were needed.

• Parasites, Hosts and Diseases
• /
• v.51 no.4
• /
• pp.461-466
• /
• 2013

From May to June 2012, a waterborne outbreak of 124 cases of cryptosporidiosis occurred in the plumbing system of an older high-rise apartment complex in Seoul, Republic of Korea. The residents of this apartment complex had symptoms of watery diarrhea and vomiting. Tap water samples in the apartment complex and its adjacent buildings were collected and tested for 57 parameters under the Korean Drinking Water Standards and for additional 11 microbiological parameters. The microbiological parameters included total colony counts, Clostridium perfringens, Enterococcus, fecal streptococcus, Salmonella, Shigella, Pseudomonas aeruginosa, Cryptosporidium oocysts, Giardia cysts, total culturable virus, and Norovirus. While the tap water samples of the adjacent buildings complied with the Korean Drinking Water Standards for all parameters, fecal bacteria and Cryptosporidium oocysts were detected in the tap water samples of the outbreak apartment complex. It turned out that the agent of the disease was Cryptosporidium parvum. The drinking water was polluted with sewage from a septic tank in the apartment complex. To remove C. parvum oocysts, we conducted physical processes of cleaning the water storage tanks, flushing the indoor pipes, and replacing old pipes with new ones. Finally we restored the clean drinking water to the apartment complex after identification of no oocysts.

• Korean Journal of Soil Science and Fertilizer
• /
• v.43 no.5
• /
• pp.558-564
• /
• 2010

Cleaning up the landfill soil by phytoremediation in association with biomass production and utilization of biosolid as a soil amendment will be an attractive green technology. In order to examine this integrated green technology, in the current study of pot trial, heavy metal removal rate and biomass production were determined following cultivation of three different plant species in the landfill soil incorporated with biosolid at two different levels (25 ton $ha^{-1}$ and 50 ton $ha^{-1}$). Among the three plant species including Indian mustard (Brassica juncea), giant sunflower (Helianthus giganteus. L), and giant cane (Arundo donax. L), sunflower appeared to produce the largest biomass yield (19.2 ton $ha^{-1}$) and the produced amounts were magnificently increased with biosolid treatment compared to the control (no biosoild treatment). The increased production associated with biosolid treatment was common for other plant species and this was attributed to the biosolid originated nutrients as well as the improved soil physical properties due to the organic matter from biosolid. The elevated heavy metals in soil which was originated from the incorporated biosolid were Cu and Zn. Based on the phytoavailable amount of heavy metals from biosolid, the removed amount by plant shoots were 95% and 165% for Cu and Zn, respectively, when sunflower was grown. This indicated that mitigation of heavy metal accumulation in soils achieved by the removal of metal through sunflower cultivation enables the successive treatment of biosolid to soils. Moreover, sunflower showed heavy metal stabilization ability in the rhizosphere resulting in alleviation of metal release to ground water.

• Journal of Biosystems Engineering
• /
• v.35 no.4
• /
• pp.244-249
• /
• 2010

This study was conducted to define the optimal Lycium chinense miller washing method for developing the Lycium chinense cleaner and we analyzed the Lycium chinense miller washing characteristics for removing pesticides and microorganism according to washing methods; habitual washing method, air bubble washing method and nozzle spray washing method. The results were summarized as follows; 1. In case of measuring physical properties according to the varieties, maximum yield strength of Hokwang was 2.562 kgf, minimum yield strength of Hokwang was 0.269 kgf and average yield strength was about 1 kgf. 2. In case of measuring change of bacteria according to washing methods, the number of bacteria of non-washing method was more than the number of bacteria of habitual washing method or mechanical washing method and the number of nozzle spray washing method was least. 3. Ahjoksiseuteurobin of 0.218 ppm was detected in the untreated sample, 0.051 ppm was detected in the habitual washing method, 0.047 ppm was detected in the air bubble washing method and 0.034 ppm was detected in nozzle spray washing method. Every amount detected were less than 2 ppm that is reference value and the detected amount was least in case of nozzle spay cleaning method. Cypermethrin of 0.772 ppm was detected in the non-cleaned sample, 0.089ppm was detected in habitual washing method, 0.26 ppm was detected in the air bubble washing method and 0.292 ppm was detected in the nozzle spray washing method. Every detected amount of Cypermethrin were less than 5 ppm that is reference value and the detected amount was least in case of habitual washing method.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.30 no.2 s.150
• /
• pp.255-265
• /
• 2006

The purpose of this study was to examine the dyeing properties of four kinds of composite yams that were twisted in different processes. The composite yarns consist of acetate and functional polyester in ratio of 70 : 30. The composite yams were dyed at 100$^{circ}C$ and 125$^{circ}C$ using three types of dyes, disperse dyes for acetate fiber, PET fiber and PET-acetate blended fiber, in the three primary colors. The exhaustion($\%$) and K/S value were observed for each case. Also the effects of four different twisting processes to dyeing properties and physical properties were examined. Regardless of twisting methods, the composite yarns that were dyed at 125$^{circ}C$ had higher exhaustion($\%$) than those were dyed at 100$^{circ}C$ with all three types of dyes; However, tendency of the K/S value after reduction cleaning process was measured at 100$^{circ}C$ and the value measured 125$^{circ}C$ had a great difference with disperse dyes for acetate and dyes for PET. The difference of the K/S values of composite yarns, when dyed at 100$^{circ}C$ and 125$^{circ}C$ with disperse dyes for PET-acetate blended fiber, was almost negligible. According to twisting methods K/S values were in the following order: AP1 > AP3 > AP4> AP2. This means that AP1, treated at 220$^{circ}C$, had the highest K/S value and K/S value becomes higher as the yam is higher twisted and becomes lower as lower twisted. On the other hand, the dry shrinkage and wet shrinkage showed low shrinkage rate when the twist was high and steam setting temperature was high.

• Journal of Korean Society on Water Environment
• /
• v.33 no.4
• /
• pp.403-408
• /
• 2017

In these days, wastewater reclamation and seawater desalination play essential role in addressing the challenge of worldwide water scarcity. Particularly, reverse osmosis (RO) for seawater desalination process is commonly used due to less energy consumption than conventional thermodynamic systems. However, membrane fouling and electrical energy consumption during operation of RO system for seawater desalination haver continued to be a obstruction to its application. In this study, therefore, wastewater secondary effluent is used for osmotic dilution of seawater. Firstly, fouling behaviour of RO by simulating wastewater effluent in osmotic dilution process was measured and we calculated energy consumption of overall desalination process by theoretical equations and commercial program. Our results reveal that RO membrane fouling can be efficiently controlled by pre-treatment systems such as nano filtration (NF) or forward osmosis (FO) process. Especially FO system for osmotic dilution process is a non-pressurized membrane system and, therefore, the operating energy consumption of overall desalination system was the lowest. Moreover, fouling layer on FO membrane is comparatively weak and reversible enough to be disrupted by physical cleaning. Thus, RO system with low salinity feed water through FO process is possible as a less energy consuming desalination system with efficient membrane fouling control.

• Membrane and Water Treatment
• /
• v.8 no.5
• /
• pp.449-462
• /
• 2017

Direct treatment of municipal wastewater by forward osmosis (FO) process was evaluated in terms of water flux decline, reverse salt diffusion, pollutants rejection and concentration efficiency by using synthetic seawater as the draw solution. It was found that when operating in PRO mode (active layer facing the draw solution), although the FO membrane exhibited higher osmotic water flux, more severe flux decline and reverse salt diffusion was also observed due to the more severe fouling of pollutants in the membrane support layer and accompanied fouling enhanced concentration polarization. In addition, although the water flux decline was shown to be lower for the FO mode (active layer facing the feed solution), irreversible membrane fouling was identified in both PRO and FO modes as the water flux cannot be restored to the initial value by physical flushing, highlighting the necessity of chemical cleaning in long-term operation. During the 7 cycles of filtration conducted in the experiments, the FO membrane exhibited considerably high rejection for TOC, COD, TP and $NH_4{^+}-N$ present in the wastewater. By optimizing the volume ratio of seawater draw solution/wastewater feed solution, a concentration factor of 3.1 and 3.7 was obtained for the FO and PRO modes, respectively. The results demonstrated the validity of the FO process for direct treatment of municipal wastewater by using seawater as the draw solution, while facilitating the subsequent utilization of concentrated wastewater for bioenergy production, which may have special implications for the coastline areas.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.2
• /
• pp.125-129
• /
• 2005

Two kinds of physical treatments were examined for the analysis both of intrinsic surface and interior nature of CuInS $e_2$[CIS] and CuGaS $e_2$[CGS] films grown in separated systems. For the first method, a selenium protection layer which was immediately deposited after the growth of the CIS was investigated. The Se cap layer protects CISe surface from oxidation and contamination during the transport under ambient atmosphere. The Se cap was removed by thermal annealing at temperature above 15$0^{\circ}C$. After the decapping treatment at 2$25^{\circ}C$ for 60 min, ultraviolet photoemission and inverse photoemission measurements of the CIS film showed that its valence band maximum(VBM) and conduction band minimum (CBM) are located at 0.58 eV below and 0.52 eV above the Fermi level $E_{F}$, respectively. For the second treatment, an Ar ion beam etching was exploited. The etching with ion kinetic energy $E_{k}$ above 500 eV resulted in broadening of photoemission spectra of core signals and occasional development of metallic feature around $E_{F}$. These degradations were successfully suppressed by decreasing $E_{k}$ below 400 eV. CGS films etched with the beam of $E_{k}$ = 400 eV showed a band gap of 1.7 eV where $E_{F}$ was almost centered.st centered.