• 수산해양기술연구
• /
• 제51권4호
• /
• pp.576-582
• /
• 2015

The efficiencies of thermal power system using fossil fuel depend on heat exchangers which extract energy from the exhaust gas before it is expelled to the atmosphere. To increase heat transfer efficiency it is very important to maintain the surface of heat exchanger as clean condition. The accepted skill of cleaning of fouled surface of heat exchanger is soot blowing. A high pressure jet of air is forced through the flat surface of plate to remove the deposit of fouling. There is, however, little knowledge of the fundamental principles of how the jet behave on the surface and how the jet actually removes the deposit. Therefore, the study focuses on the measuring of cleaning area and cleaning dwell time after accumulating the simulated deposit on the flat surface. The deposit test rig was built for the study and simulated deposit material is used after measuring the physical property of the each material by shearing stress test. Much data was obtained for the analysis by the parameters change such as the different jet speed, different inner pressure and variable distance of the jet from the test rig surface. The experimental data was compared with the theoretical equation and most of the data matches well except some extreme cases.

• 한국환경과학회지
• /
• 제17권8호
• /
• pp.925-932
• /
• 2008

Manufactures of automotive repair finishes are tending to reduce more and more the level of volatile organic compounds (VOCs) in their paint processes in order to comply with increasingly strict environmental legislation. The production of high solids paints is a way to solve this problem. However, the application of high-solids paints is limited primarily by the viscosity of resin which is strongly related to painting ability: the higher solid content, the lower desired property. In this study, alkyl copolymer with low viscosity was synthesized by the introduction of the monomers with long-side chains and functional groups which improve flexibility and cross-linking density, respectively. The solid content of the paint prepared with the synthesized resin was 80wt% and its VOCs was reduced by 20%, compared to the commercialized paint. Also, the physical and mechanical properties of coatings on steel sheets were similar to commercialized one.

• Advances in concrete construction
• /
• 제9권6호
• /
• pp.589-596
• /
• 2020

In an effort to find alternate, environment friendly and sustainable building materials, the scope of possible utilization of iron slag (I-sand), generated as a by-product in iron and steel industries, as fine aggregates in reinforced cement concrete (RCC) made with manufactured sand (M-sand) is examined in this manuscript. Systematic investigations of the physical, mechanical, microstructural and durability properties of I-sand in comparison with RCC made with M-sand have been carried out on various mix designs prepared by the partial/full replacement of I-sand in M-sand. The experimental results clearly indicate the possibility of utilizing iron slag for preparing RCC in constructions without compromising on the property of concrete, durability and performance. This provides an alternate possibility for the effective utilization of industrial waste, which is normally disposed by delivering to landfills, in building materials which can reduce the adverse environmental effects caused by indiscriminate sand mining being carried out to meet the growing demands from construction industry and also provide an economically viable alternative by reducing the cost of concrete production.

• 한국의류산업학회지
• /
• 제5권4호
• /
• pp.408-412
• /
• 2003

The micro structure of POY was modified and a wool-like touch yarn of composite fibers with different shrinkage was made. With this yarn 12 different fabrics with wool like touch were prepared. The characteristic physical property changes of the fabrics examined are as follows: 1. In all cases, the initial high shrinkage stages were observed in hot water treatment and the 3D images of complex multilayer of typical doubling fibers with different shrinkage were also observed in hot air treatment of 170C. 2. The tensile strength changes of satin and plain fabrics with the change of twist count showed similar behavior. However, WT's were slightly higher and RT's was lower in twill and satin fabrics than those in plain fabric. 3. Since a slight decrease of B's of twill fabric found with increasing twist count under given experimental condition, it could be influenced on the anti-drape stiffness was decreased and flexibility was increased. 4. A significant decrease of G values was observed in the twist count 800-1000 T.P.M However, in the twist count higher than 1000 T.P.M G values observed were kept nearly constant. 5. MIU of plain and twill fabrics showed a drastic decrease at the twist count higher than 1000 T.P.M.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 추계학술대회 논문집
• /
• pp.63-66
• /
• 2005

Nanoimprint lithography (NIL) process at room temperature has been newly proposed in recent years to overcome the shape accuracy and sticking problem induced in a conventional NIL process. Success of the room temperature NIL relies on the accurate understand of the mechanical behavior of the polymer. Since a conventional NIL process has to heat a polymer above the glass transition temperature to deform the physical shape of the polymer with a mold pattern, viscoelastic property of polymer have major effect on the NIL process. However, rate dependent behavior of polymer is important in the room temperature NIL process because a mold with engraved patterns is rapidly pressed onto a substrate coated with the polymer by the hydraulic equipment. In this paper, finite element analysis of the room temperature NIL process is performed with considering the strain rate dependent behavior of the polymer. The analyses with the variation of imprinting speed and imprinting pattern are carried out in order to investigate the effect of such process parameters on the room temperature NIL process. The analyses results show that the deformed shape and imprint force is quite different with the variation of punch speed because the dynamic behavior of the polymer is considered with the rate dependent plasticity model. The results provide a guideline for the determination of process conditions in the room temperature NIL process.

• 한국염색가공학회지
• /
• 제23권1호
• /
• pp.51-59
• /
• 2011

Calcium alginate fiber were prepared by wet spinning of various conditions, including different concentrations of sodium alginate solution and $CaCl_2$ concentrations for coagulating the fiber through an absorption of calcium ion. The absorption of calcium ion during the coagulating step lead to solidify the fibers by the replacement of sodium ion with calcium ion to produce some crosslinking. The concentration of calcium ion in the calcium alginate fiber seems to be well related to the mechanical and physical property of the fiber, such as fiber strength moisture regain, and degree of swelling. The tensile strength of calcium alginate fiber was increased along with the increasing amount of sodium alginate solution. According to EDS analysis, 7 wt% $CaCl_2$ coagulation bath resulted in more calcium ion in the fiber compared to 3 wt% $CaCl_2$ coagulation bath. The decomposition temperature of calcium alginate fiber was $199^{\circ}C$, which $14^{\circ}C$ higher than that of sodium alginate.

• 한국재료학회지
• /
• 제20권10호
• /
• pp.555-558
• /
• 2010

This study examined the effect of current density on the surface morphology and physical properties of copper plated on a polyimide (PI) film. The morphology, crystal structure, and electric characteristics of the electrodeposited copper foil were examined by scanning electron microscopy, X-ray diffraction, and a four-point probe, respectively. The surface roughness, crystal growth orientation and resistivity was controlled using current density. Large particles were observed on the surface of the copper layer electroplated onto a current density of 25 mA/$cm^2$. However, a uniform surface and lower resistivity were obtained with a current density of 10 mA/$cm^2$. One of the important properties of FCCL is the flexibility of the copper foil. High flexibility of FCCL was obtained at a low current density rather than a high current density. Moreover, a reasonable current density is 20 mA/$cm^2$ considering the productivity and mechanical properties of copper foil.

• 한국재료학회지
• /
• 제18권8호
• /
• pp.427-431
• /
• 2008

The mechanical property of a phosphore layer was investigated by measuring the resolution (LP/mm) and by positron annihilation spectroscopy and SEM. Image plate samples containing the phosphore layer were irradiated by X-rays in a hospital numerous times over a course of several years. The LP/mm values of a (Ba,Sr)FBr : Eu image plate irradiated by X-rays varied between 2.2 and 2.0 over a period of four years. Coincidence Doppler Broadening (CDB) positron annihilation spectroscopy was used to analyze defect structures. The S parameters of the samples from hospital use varied from 0.6219 to 0.6232. There was a positive relationship between the time of exposure to the X-rays and the S parameters. Most of the defects were found to have been generated by X-rays.

• 토지주택연구
• /
• 제3권1호
• /
• pp.83-88
• /
• 2012

In this study, physical characteristics of cement and/or concrete materials that are typically used for energy-foundation (EF) structures have been studied. The thermal conductivity and structural integrity of the cement-based materials were examined, which are commonly encountered in backfilling a vertical ground heat exchangers, cast-in-place concrete piles and concrete lining in tunnel. For this purpose the thermal conductivity and unconfined compression strength of cement-based materials with various curing conditions were experimentally estimated and compared. Hydration heat generated from massive concrete in the cast-in-place concrete energy pile was observed for 4 weeks to estimate its dissipation time in the underground. The hydration heat may mask the in-situ thermal response test (TRT) result performed in the cast-in-place concrete energy pile. It is concluded that at least two weeks are needed to dissipate the hydration heat in this case. In addition, a series of numerical analysis was performed to compare the effect of thermal property of the concrete material on the cast-in-place pile.

• 한국의류학회지
• /
• 제25권10호
• /
• pp.1809-1820
• /
• 2001

본 연구에서는 모 직물의 접착심과의 접착 후, 프레싱 처리 후, 드라이클리닝 처리 후 프레스로 처리한 실제의 의복의 관리와 생산 면에서 접할 수 있는 직물 변화에 대하여 물성 변화를 살펴보았다. 겉감으로는 신사복 춘하용 모 100% 또는 모혼방 직물 15종류를 사용하였으며 심지로는 신사복에 많이 쓰이는 3종류 심지를 사용하였다. KES시스템을 이용하여 직물의 접착후, 프레싱 처리 후, 드라이크리닝과 프레싱 처리 후의 물성 변화를 시험하였으며 다음과 같은 결과를 얻었다. 1) 접착 후 EM은 대체로 감소하지만 강성과 이력 현상은 증가하는 것으로 나타났다. 결과로 KOSHI, SHARI, HARI는 증가하고 THV는 감소하여 태는 접착으로 저하되었다. 2) 프레싱 처리 후는 접착 후와 큰 차이를 보이지 않는다. 마찰특성에서 좀더 매끄러워지고 마찰 계수는 증가하는 것으로 나타났다. 3) 드라이크리닝과 프레싱 처리 후의 물성의 변화에서는 위사 방향의 큰 값을 갖는 경우에 감소하는 것으로 나타났다. 굽힘 강성과 전단강성은 감소하였지만 이력은 증가하는 흥미로운 결과를 보인다. 드라이클리닝 용제의 효과로 여겨진다. 무게는 증가하여 직물이 처리 후 수축한 것으로 나타났다. 프레싱 처리 후와 비교시 KOSHI, SHARI, HARI와 FURAMl는 감소하고 THV는 증가하여 태가 향상하였다.