• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.631-634
• /
• 2001

This paper presents a maximum power point tracking without a current sensor for a small scale photovoltaic power system. The small scale photovoltaic power systems are used in parallel, and so the cost and the reliability are strongly demanded. In the proposed inverter, the current is controlled with open loop, and then the power of photovoltaic array is calculated by the equation using the voltage of the photovoltaic array. Therefore, the system can obtain the power by detecting only the voltage of the photovoltaic array. As a result, we may obtain the performance of the MPPT with a current sensor as well as with a current sensor.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.1
• /
• pp.56-61
• /
• 2019

In this study, a reduction method of leakage current in a three-level photovoltaic power-conditioning system (PCS) is proposed and verified by simulation and experiment. Leakage current generation is analyzed through an equivalent model of the common mode voltage considering a significant parasitic capacitance existing between the photovoltaic array and ground. A leakage current reduction method using pulse-width modulation (PWM) method is also proposed, and a 10-kW three-level photovoltaic PCS simulation and experiment is performed with a $1{\mu}F$ parasitic capacitor based on 100 nF/kW. The proposed method using the PWM method is verified to reduce the leakage current by 73% compared with the conventional PWM method.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.4 no.4
• /
• pp.325-331
• /
• 1999

In a utility interactive photovoltaic generation system. a PWM inverter is used for the connection between the p photovoltaic arrays and the utility. The dc current becomes pulsated when the conventional inverter system operates i in the continuous current mode and de current pulsation causes the distortion of the accurrent waveform. This paper p presents the reduced pulsation of de input current by operating the inverter with buck-boost chopper in the d discontinuous conduction mode. The dc current which contains harmonic component is analyzed by means of s separating into two terms of a ripple component and a direct component. The constant dc current without p pulsation is supplied from photovoltaic array to the inverter. The proposed inverter system provides a sinusoidal ac c current for domestic loads and the utility line with unity power factor.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.346-347
• /
• 2020

This paper presents the two combination methods for leakage current reduction in photovoltaic system PCS. The leakage current in the photovoltaic system generated from the parasitic capacitance existing between the photovoltaic system and ground relevance to common mode voltage caused by PWM switching. Firstly, Leakage current reduced by a PWM method using two carriers with 180-degree phase different. Secondly, the leakage current is more reduced by connecting LCL filter to the mid-point of DC link. This combining method is revealed in PSIM simulation with 1 uF parasitic capacitance.

• Current Optics and Photonics
• /
• v.3 no.6
• /
• pp.516-521
• /
• 2019

The electrical leakage levels of GaN-based light-emitting diodes (LEDs) containing leakage paths are estimated using photoluminescence (PL) and photovoltaic properties under photoexcitation conditions. The PL intensity and open-circuit voltage (V_OC) decrease because of carrier leakages depending on photoexcitation conditions when compared with reference values for typical LED chips without leakage paths. Changes of photovoltage-photocurrent characteristics and PL intensity due to carrier leakage are employed to assess the leakage current levels of LEDs with leakage paths. The current corresponding to the reduced V_OC of an LED with leakage from the photovoltaic curve of a reference LED without leakage is matched with the leakage current calculated using the PL intensity reduction ratio and short-circuit current of the LED with leakage. The current needed to increase the voltage for an LED with a leakage under photoexcitation from V_OC of the LED up to V_OC of a reference LED without a leakage is identical to the additional current needed for optical turn-on of the LED with a leakage. The leakage current level estimated using the PL and photovoltaic properties under photoexcitation is consistent with the leakage level measured from the voltage-current characteristic obtained under current injection conditions.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.25 no.9
• /
• pp.14-25
• /
• 2011

The solar vehicle is in the spotlight in the eco-friendly aspect of photovoltaic system using unlimited solar energy. The solar vehicle uses energy of photovoltaic and battery. The solar vehicle uses stored energy in battery when photovoltaic power is lower than consumption power by solar vehicle and if photovoltaic power is higher than consumption power by solar vehicle then photovoltaic power is stored to battery. To improve use efficiency of photovoltaic, the researches about MPPT method to operate maximum power point and interior permanent magnet synchronous motor(IPMSM)drive system using photovoltaic is necessary. This paper proposes MPPT control algorithm for solar vehicle using new fuzzy control(NFC). In this paper, to reduce switching loss, the DC-DC converter is omitted. The NFC controller can be use instead of PO. The NFC controller is performed MPPT control using solar cell voltage and q -axis current of IPMSM. The output of NFC is command q -axis current of IPMSM and this current is operated IPMSM. The response characteristics of algorithm proposed in this paper is compared response characteristics of conventional PO method by PSIM program and validity of this paper prove using this result.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.10
• /
• pp.1796-1801
• /
• 2008

In this paper, a new current based maximum power point tracking (CMPPT) method is proposed for a single phase photovoltaic power conditioning system and the current based MPPT modifies incremental conductance method. The current based MPPT method makes the entire control structure of the power conditioning system simple and uses an inherent current source characteristic of solar cell array. In addition, digital phase locked loop using an all pass filter is introduced to detect phase of grid voltage as well as peak voltage. Controllers about dc/dc boost converter, dc-link voltage, dc/ac inverter is designed for a coordinated operation. Furthermore, PI current control using a pseudo synchronous d-q transformation is employed for grid current control with unity power factor. 3kW prototype photovoltaic power conditioning system is built and its experimental results are given to verify the effectiveness of the proposed control schemes.

• The Korean Journal of Ceramics
• /
• v.6 no.3
• /
• pp.262-266
• /
• 2000

We investigated the effect of the grain size on the photovoltaic current in (Pb$_{1-x}$La$_x$)TiO$_3$ceramics, and the photoinduced domain switching in (Pb$_{0.85}$La$_{0.15}$)TiO$_3$and BaTiO$_3$ceramics. These behaviors in ferroelectric ceramics were attributed to the grain boundary at which photoexcited electrons were trapped. As the charged grain boundary acted as an electro-potential barrier which impeded the movement of electrons, the photovoltaic current showed a peak at a critical grain size. The space charge field built by the electrons trapped at the grain bound-aries was accounted for the photoinduced domain switching, and AE experimental results support well this account.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.9
• /
• pp.14-19
• /
• 2014

Recently, many renewable energy generating businesses are ongoing progress due to the introduction of the RPS(Renewable Portfolio Standards) as well as the needs of environmentally friendly energy resources. Researches on photovoltaic system are actively being processed since the photovoltaic system is relatively easy to install and becomes commercialized in many domestic application areas. Furthermore, the floating photovoltaic system is likely to be installed more actively since the conventional photovoltaic system requires relatively large areas of land. Also, the floating photovoltaic system is more efficient than photovoltaic system installed in land due to the operation in lower temperature. However, safety problems such as electric shock could arise since the cable should be installed in the water. In this paper, the leakage current and the voltage rising are measured and analyzed for the case when the cables are damaged connecting the floating photovoltaic system to the grid.

• Current Photovoltaic Research
• /
• v.6 no.3
• /
• pp.81-85
• /
• 2018

The photovoltaic modules installed in the actual field are affected by various external environments and the electrical performance output value is generally lowered compared to initial output value. The most of photovoltaic modules consists of low iron glass, encapsulant (EVA), back sheet, frame and junction box assembly based on the solar cells. In this paper, the characteristics of encapsulant which is an important constituent material of photovoltaic module were verified by maximum power determination, electro luminescence images, yellowness index measurement, and gel content measurement after ultraviolet (UV) irradiation exposure. The most commonly installed 72 cells crystalline photovoltaic modules were tested after various UV exposure of 0, 15, 30, and $60kWh/m^2$ and compared with the reference module. After UV exposure of $15kWh/m^2$, which is the current international test condition, a small amount of change was observed in yellowness index and electroluminescence, while a gell content rapidly increased. At a cumulative dose of $60kWh/m^2$, which will be a new international test condition in the near future, however, the yellowness index increased sharply and showed the greatest output power drop.