• Journal of Environmental Science International
• /
• v.16 no.4
• /
• pp.433-440
• /
• 2007

The photodegradation and by-products of the gaseous toluene with $TiO_2$ (P25) and short-wavelength UV ($UV_{254+185nm}$) radiation were studied. The toluene was decomposed and mineralized efficiently owed to the synergistic effect of photochemical oxidation in the gas phase and photocatalytic oxidation on the $TiO_2$ surface. The toluene by the $UV_{254+185nm}$ photoirradiated $TiO_2$ were mainly mineralized $CO_2$ and CO, but some water-soluble organic intermediates were also formed under severe reaction conditions. The ozone and secondary organic aerosol were produced as undesirable by-products. It was found that wet scrubber was useful as post-treatment to remove water-soluble organic intermediates. Excess ozone could be easily removed by means of a $MnO_2$ ozone-decomposition catalyst. It was also observed that the $MnO_2$ catalyst could decompose organic compounds by using oxygen reactive species formed in process of ozone decomposition.

• Rapid Communication in Photoscience
• /
• v.3 no.2
• /
• pp.35-37
• /
• 2014

PEC (photoelectrochemical) water splitting for $O_2/H_2$ production is one of the promising but difficult way to utilize solar energy. Among photocatalytic materials for PEC water oxidation, $BiVO_4$ (Eg = 2.4 eV) has been recently intensively studied since it has various advantageous properties. But its maximum efficiency has not been realized owing to kinetic factors - slow water oxidation at surface & insufficient stability. These problems can be simultaneously solved by application of oxygen evolution catalyst (OEC) such as $CoO_x$, Co-Pi, $IrO_x$ etc. Herein we report the first successful application of $NiFeO_x$ OEC on $BiVO_4$, showing good performance compared to other effective OEC applied on $BiVO_4$ under basic conditions. The enhanced activity of OEC loaded $BiVO_4$ has been supported by the surface charge separation efficiency and electrochemical impedance studies.

• Journal of environmental and Sanitary engineering
• /
• v.20 no.4 s.58
• /
• pp.45-50
• /
• 2005

Titania gel formations were prepared by sol-gel method using titanium(IV) chloride $(TiCl_4)$, and its characteristics were analyzed by varying the $epoxide/TiCl_4$ ratio and the amount of water In the end, titania $(TiO_2)$ aerogel were prepared using supercritical drying process. VOCs such as benzene, toluene, and m-xylene (BTX) were oxidized using prepared titania aerogel and commercially available $TiO_2$, and its performance was compared. The surface area, pore volume, and average pore diameter of 1,2-epoxybutane are significantly smaller than the propylene oxide. And the titania aerogels with 6 moi of epoxides have high surface areas, pore volumes, and average pore diameters. As a result of photo-oxidation, conversion of benzene was reached about $70\%$, and other reactants were reached about $60\%$ similarly. The conversion of BTX was increased as inlet concentration decreased. The reactivity of titania calcined at $600^{\circ}C$ was greater than $400^{\circ}C$ and $800^{\circ}C$. Water is required as a reactants for the oxidation of VOCs, and the continuous consumption of hydroxyl radicals required replenishments to maintain catalyst activity. The activity ratio increased with increasing reaction time when enough amount of water was present in the reactor.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.1
• /
• pp.35-42
• /
• 2010

In this paper, three types of CNT/$TiO_2$ composite electrodes were prepared with different methods. The changes in XRD patterns showed that the Electrode A contained a mixed phase of anatase and rutile while the Electrode B and Electrode C contained a typical single and clear anatase crystal structure. From SEM micrographs, $TiO_2$ particles were adhered on the surface of the CNT network in the forms of small clusters. The results of chemical elemental analysis indicated that the main elements such as C, O and Ti were existed. The results demonstrated that the efficiency of photoelectrocatalytic (PEC) oxidation for methylene blue (MB) was higher than that of photocatalytic (PC) oxidation. There was a clear enhancement trend of the MB degradation using the prepared CNT/$TiO_2$ composite electrodes with an increase of applied potential. Finally, the prominent PEC activities of the CNT/$TiO_2$ composites could be attributed to combination effects of photo-degradation of $TiO_2$, electron assistant of CNT and function of applied potential.

• Membrane Journal
• /
• v.4 no.3
• /
• pp.152-162
• /
• 1994

The photodegradation efficiency of formic acid on $TiO_2$ photocatalytic membranes was investigated. A new titania membrane reactors for purification of water combining microfiltration with photocatalytic degradation of organic compounds were developed. Titania membrane tubes(average pore size of $0.2\mu m$) were prepared by the slip casting, and porous thin films of $TiO_2$ were formed on the tube surface by the sol-gel process to increase the surface area, and consequently to increase photodegradation efficiency of organic compounds. The UV light with the wavelength of 365 nm was used as a light source for photocatalytic reactions. The photodegradation efficiency of the organic compounds was strongly dependent on the flux of the solution, the microstructure of the membrane (sol pH), and the amount of $O_2$ supplied. The effects of the primary oxidant such as $H_2O_2$ and dopants such as $Nb_2O_5$ on the photodegradation efficiency were also investigated. The results showed that more than 80% of formic acid could be degraded using membrane coated with a $TiO_2$ sol of pH 1.45. The photodegradation efficiency could be improved by about 20% when adding $H_2O_2$ in feed solution or doping $TiO_2$ membranes with $Fe_2O_3$.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.3
• /
• pp.316-322
• /
• 2006

The current study evaluated the technical feasibility of the application of $TiO_2$ photocatalysis for the removal of nocotine which has well known as a representative material of environmental tobacco smoke(ETS). Four different preliminary experiments were performed for the evaluation of nicotine removal using photocatalyst-coated construction materials. The photocatalytic removal of nicotine was investigated for five parameters: dry condition of coating tiles, type of coating sol, number of coatings, relative humidity(RH), and input concentrations. Prior to performing the parameter tests, adsorption of nicotine onto the current experimental system was surveyed. All the variables tested in the present study exhibited to influence the photocatalytic decomposition of Nicotine. A dry condition of high temperature and short dry period presented higher photocatalytic oxidation(PCO) efficiency compared to that of low temperature and long dry period. ST-KO3 sol showed higher decomposition efficiency than E-T Sol. The PCO efficiency increased as the number of coating increased. High humidity and low input concentrations exhibited higher PCO efficiency. Consequently, it is noted that the five parameters tested in the present study should be considered for the application of photocatalyst-coated construction materials in cleaning nicotine in ETS.

• Journal of Korean Society on Water Environment
• /
• v.35 no.6
• /
• pp.459-469
• /
• 2019

The ozonation of sulfamethoxazole (SMX) was performed at 20℃ using a pilot scale countercurrent bubble column reactor. Ozonation systems were combined with UV irradiation and TiO₂ addition. As the oxidation reaction proceeded in each treatment system, the pH of the sample decreased and in the O₃/UV/TiO₂ system, the pH change was the largest from 4.54 to 2.02. Under these experimental conditions, the scavenger impact of carbonate is negligible. The highest COD and TOC removal rate was observed in the O₃/UV/TiO₂ system due to the UV irradiation and the photocatalytic effect of TiO₂. Also, the highest mineralization ratio(ε) value is 0.2 in the O₃/UV/TiO₂ system, which means theoxidation capacity of the systems. The highest SMX degradation rate constants calculated by COD and TOC values (COD and TOC) were 2.15 × 10^-4 sec^-1 and 1.00 × 10^-4 sec^-1 in the O₃/UV/TiO₂ system, respectively. The activation energy (E_a) of ozone treatment follows the Arrhenius law. It was calculated based on _COD and _TOC. Each activation energy decreased in order of single O₃> O₃/TiO₂> O₃/UV > O₃/UV/TiO₂ system. The result showed that ΔH^≠ is more effective than ΔS^≠ in each SMX ozontaionsystem, that is characteristic of the common oxidation reaction.

• Korean Journal of Materials Research
• /
• v.18 no.11
• /
• pp.583-591
• /
• 2008

In this study, two series of CNT/$TiO_2$ electrodes were prepared. The decrease of surface area compared with that of the pristine carbon nanotubes (CNTs) indicated the blocking of micropores on the surface of the CNTs; was further supported by scanning electron microscopy (SEM) and field emission SEM (FE-SEM) observations. The X-ray diffraction (XRD) results showed that the CNT/$TiO_2$ composites contained a mix of anatase and rutile forms of $TiO_2$ particles when the precursor was $TiO_2$ powder, whereas when the precursor was Ti ($OC_4H_7$) (TNB), the composites contained only the typical single and clear anatase $TiO_2$ particles. The energy dispersive X-ray spectroscopy (EDX) spectra showed the presence of C, O and Ti peaks for all samples. It was found that catalytic decomposition of methylene blue (MB) solution could be attributed to synthetic effects between the $TiO_2$ photocatalysis and electro-assisted CNTs network, and that photoelectrocatalytic oxidation increased with an increase of CNT composition. It was also found that the photoelectrocatalytic oxidation efficiency for MB is higher than that of photocatalytic oxidation. Moreover, the CNT/$TiO_2$ composites catalyst prepared by the impregnation method demonstrates higher photoelectrocatalytic activity than the mechanical mixture with the same CNT content.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.141-141
• /
• 2018

Copper is one of the most abundant metals on earth. Its oxide (CuO) is an intrinsically p-type metal-oxide semiconductor with a bandgap ($E_g$) of 1.2-2.0 eV 1. Copper oxide nanomaterials are considered as promising materials for a wide range of applications e.g., lithium ion batteries, dye-sensitized solar cells, photocatalytic hydrogen production, photodetectors, and biogas sensors 2-7. Recently, high-density and uniform CuO nanostructures have been grown on Cu foils in alkaline solutions 3. In 2011, T. Soejima et al. proposed a facile process for the oxidation synthesis of CuO nanobelt arrays using $NH_3-H_2O_2$ aqueous solution 8. In 2017, G. Kaur et al. synthesized CuO nanostructures by treating Cu foils in $NH_4OH$ at room temperature for different treatment times 9. The surface treatment of Cu in alkaline aqueous solutions is a potential method for the mass fabrication of CuO nanostructures with high uniformity and density. It is interesting to compare the gas sensing properties among CuO nanomaterials synthesized by this approach and by others. Nevertheless, none of above studies investigated the gas sensing properties of as-synthesized CuO nanomaterials. In this study, CuO nanowalls versus nanoparticles were synthesized via the oxidation process of Cu foil in NH4OH solution at $50-70^{\circ}C$. The gas sensing properties of the as-prepared CuO nanoplates were examined with $C_2H_5OH$, $CH_3COCH_3$, and $NH_3$ at $200-360^{\circ}C$.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1993.10a
• /
• pp.39-39
• /
• 1993

반도성 세라믹 광촉매 막 반응기 (membrane reactor)에 의한 난분해성 유독 유기물질의 분해공정을 개발하기 위한 기초연구로서 $TiO_2$ 막 반응기의 formic acid 및 trichloromethane에 대한 광분해 효율이 연구되었다. 막 반응기는 용액의 정밀여과 (microfiltration)는 물론 유기물의 광분해를 동시에 수행할 수 있도록 다공성 $TiO_2$ 튜브 (평균기공 : $0.2 \mu m$)를 이용한 새로운 타입으로 ㅐㄱ발되었으며 광원으로는 365 nm 파장을 갖는 UV를 사용하였다. 또한 반응기의 광분해 효율을 증진시키기 위하여 슬립케스팅법으로 제조한 $TiO_2$ 튜브표면을 $TiO_2$ 졸로 코팅하였다.