• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.55-61
• /
• 2021

In this paper, we proposed and implemented defect detection methods of polarized film with half-wave phase retardation plates. We investigated the principles of phase retardation compensation and optical principle of half-wave phase retardation plates. We analyzed of samples of polarized film with half-wave phase retardation plates. The optical defect detection methods are proposed and the performance is validated with experiments.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.4 no.2
• /
• pp.7-14
• /
• 1985

An experiment to investigate the rate of change of phase angle of eddy current output signal caused by outer surface defect of nonferromagnetic tube by variation of standard depth of penetration and variation of percent of tube wall penetration was carried out. The results of the experiment show that the phase angle of defect signal is increased with decreasing the standard depth of penetration or the depth of defect. The results also show that the phase angle is decreased with increasing the skin effect of eddy current, and that the resolution is decreased with decreasing the depth of defect.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.4
• /
• pp.321-327
• /
• 2007

In lock-in thermography, a phase difference between the defect area and the healthy area indicates the qualitative location and size of the defect. To accurately estimate these parameters, the shearing-phase technique has been employed which gives the shearing-phase distribution. The shearing-phase distribution has maximum, minimum, and zero points that help determine quantitatively the size and location of the subsurface defect. In experiment, the proposed technique is verified with artificial specimen and these related factors are analyzed.

• The KIPS Transactions:PartD
• /
• v.15D no.3
• /
• pp.313-320
• /
• 2008

A typical software development life cycle consists of a series of phases, each of which has some ability to insert and detect defects. To achieve desired quality, we should progress the defect removal with the all phases of the software development. The well-known model of phase-based defect profile is Gaffney model. This model assumes that the defect removal profile follows Rayleigh curve and uses the parameters as the phase index number. However, these is a problem that the location parameter cannot present the peak point of removed defects when you apply Gaffney model to the actual situation. Therefore, Gaffney model failed to represent the actual defect profile. This paper suggests two different models: One is modified Gaffney model that introduce the parameter of Putnam's SLIM model to replace of the location parameter, the other is the growth function model because the cumulative defect profile shows S-shaped. Suggested model is analyzed and verified by the defect profile sets that are obtained from 5 different software projects. We could see from the experiment, the suggested model performed better result than Gaffney model.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.10
• /
• pp.2000-2004
• /
• 2009

In general, for the condition monitoring of a power transformer using the UHF PD measuring technique, detection of any partial discharge, identifying the defect in the transformer and locating the insulation defect are necessary. In this paper one of the most frequent detects which can result in turn to turn fault in power transformer was examined for identifying the defect. In order to model the defect, as a discharge source, a partial discharge cell was used for experimental activity. Magnitude of electromagnetic wave signals and corresponding amount of apparent discharge were measured simultaneously against phase of applied voltage to the discharge cell. Frequency range and phase resolved partial discharge signals were measured and analyzed. The results will be contributed to build the defect database of power transformer and to decrease the occurrence of transformer faults.

• Journal of the Korean Ceramic Society
• /
• v.41 no.5
• /
• pp.406-409
• /
• 2004

A blue phosphor(ZnS:Cu) is manufactured by solid state reaction for ACPEL(AC powder EL). The effect of artificial defect on phosphor surface on the ZnO phase conversion and resulting luminescence have been studied. It was found that ZnS:Cu could converse to cubic phase more easily due to the formation of artificial defect on 1st fired phosphor by ball-milling process, resulting in improvement of luminescence of phosphor phosphors under the driven EL condition. We found out an optimized ball-mill condition through considering effect of each ball-mill conditions such as milling time and milling rpm on defect. Also we determined relationship between emission luminescence and phase of phosphor based on analyses of crystal structures of phosphors. A significant improvement above 30% was observed in electroluminescence by the artificial defect on ZnS:Cu phosphors compared to non-treated phosphors.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.1
• /
• pp.40-45
• /
• 2013

The purpose of this study was to detect the pin hole defect of dental composite restoration using lock-in thermography method. Amplitude and phase images of the composite resin specimens were analyzed according to the lock-in frequency and the diameter of defect area. Through the amplitude image analysis, at lock-in frequency of 0.05 Hz, defect diameters 2-5 mm exhibited the highest amplitude contrast value between defective area and sound area. The lock-in frequency range of 0.3-0.5 Hz provided good phase angle contrast for the defect area. At lock-in frequency range of 0.5 Hz, defect diameter of 5 mm exhibited the highest phase contrast value. It is concluded that the infrared lock-in thermography method verified the effectiveness for detecting the pin hole defect of dental composite restoration.

• Journal of the Optical Society of Korea
• /
• v.19 no.6
• /
• pp.619-628
• /
• 2015

In this paper, we consider a method for estimating a stripe-type defect and the reconstruction of a defect-free L/S type mask used in lithography. Comparing diffraction patterns of defected and defect-free masks, we derive equations for the estimation of the location and size of the defect. We construct an analytical model for this problem and derive closed form equations to determine the location and size using phase retrieval problem solving techniques. Consequently, we develop an algorithm that determines a defect-free mask pattern. An example shows the validity of the equations.

• Clinical and Experimental Reproductive Medicine
• /
• v.30 no.1
• /
• pp.15-21
• /
• 2003

Objective : Clomiphene citrate is one of the most commonly used drugs in the treatment of infertility, but the pregnancy rate achieved with clomiphene citrate is significantly lower than the ovulation rate due to its antiestrogenic effect on the endometrium. Endometrial prolactin is considered to be a marker and an inducer of predecidualization that is characteristic of secretory endometrium. The purpose of this study was to evaluate the association of clomiphene citrate and unsatisfactory endometrial differentiation to secretory endometrium by examining the endometrial expression of prolactin in clomiphene citratetreated infertile women with luteal phase defect. Methods : The endometrial samples from infertile women with luteal phase defect (n=27) were examined. Five cases during secretory phase and six cases during proliferative phase were obtained by biopsy. Sixteen cases were obtained by biopsy during secretory phase after clomiphene citrate treatment. By immunohistochemical staining for prolactin, all obtained endometrial tissues were examined. The differences in the endometrial expression of prolactin were evaluated between proliferative phase and secretory phase, and between clomiphene citrate treated group and no treatment group during secretory phase. Results: The staining of endometrial prolactin was significantly more intense in the glandular epithelial cells and stromal cells in the secretory endometrium than in the proliferative endometrium. The glandular expression of prolactin in the secretory endometrium was not significantly different between the clomiphene citrate-treated group and no treatment group (p=0.719), but the staining of prolactin in the stromal cells was significantly less intense in the clomiphene citrate-treated group than no treatment group (p=0.019). Conclusion: In this investigation, we demonstrated that the endometrial stromal expression of prolactin in the secretory phase was significantly lower in the clomiphene citrate-treated group campared with no treatment group in infertile women with luteal phase defect. And our finding suggests that clomiphene citrate may have an adverse effect on the endometrial predecidualization in infertile women.

• Journal of Korean Society for Quality Management
• /
• v.37 no.3
• /
• pp.83-93
• /
• 2009

This study proposes a stepwise approach to product safety management(PSM), of which roadmap consists of five phases. ISO 9001 QM model is assumed as the first-phase model and each higher-phase model is built by adding a corresponding module to the lower one. In the phase order, those modules are CCMS, a failure to warn, manufacturing defect and design defect. The progress in PSM of a domestic food company is discussed.