• Journal of the Korean Physical Society
• /
• v.73 no.11
• /
• pp.1703-1707
• /
• 2018

Ferromagnetic ${\tau}-phase$ $Mn_{54}Al_{46}C_{2.44}$ particles were synthesized, and its composites with commercial $Sm_2Fe_{17}N_3$ and synthesized $Fe_{65}Co_{35}$ powders were fabricated. Smaller grain size than the single domain size of the $Mn_{54}Al_{46}C_{2.44}$ without obvious grain boundaries and secondary phases is the origin for the low intrinsic coercivity. It was confirmed that the magnetic properties of the $Mn_{54}Al_{46}C_{2.44}$ can be enhanced by magnetic exchange coupling with the hard magnetic $Sm_2Fe_{17}N_3$ and soft magnetic $Fe_{65}Co_{35}$. The high degrees of the exchange coupling were verified by calculating first derivative curves. Thermo-magnetic stabilities of the composites from 100 to 400 K were measured and compared. It was demonstrated that the $Mn_{54}Al_{46}C_{2.44}$ based composites containing $Sm_2Fe_{17}N_3$ and $Fe_{65}Co_{35}$ could be promising candidates for future permanent magnetic materials with the proper control of purity, magnetic properties, etc.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.427-427
• /
• 2016

Organic-inorganic hybrid perovskite have attracted significant attention as a new revolutionary light absorber for photovoltaic device due to its remarkable characteristics such as long charge diffusion lengths (100-1000nm), low recombination rate, and high extinction coefficient. Recently, power conversion efficiency of perovskite solar cell is above 20% that is approached to crystalline silicon solar cells. Planar heterojunction perovskite solar cells have simple device structure and can be fabricated low temperature process due to absence of mesoporous scaffold that should be annealed over 500 oC. However, in the planar structure, controlling perovskite film qualities such as crystallinity and coverage is important for high performances. Those controlling methods in one-step deposition have been reported such as adding additive, solvent-engineering, using anti-solvent, for pin-hole free perovskite layer to reduce shunting paths connecting between electron transport layer and hole transport layer. Here, we studied the effect of alkali metal halide to control the fabrication process of perovskite film. During the morphology determination step, alkali metal halides can affect film morphologies by intercalating with PbI2 layer and reducing $CH3NH3PbI3{\cdot}DMF$ intermediate phase resulting in needle shape morphology. As types of alkali metal ions, the diverse grain sizes of film were observed due to different crystallization rate depending on the size of alkali metal ions. The pin-hole free perovskite film was obtained with this method, and the resulting perovskite solar cells showed higher performance as > 10% of power conversion efficiency in large size perovskite solar cell as $5{\times}5cm$. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and inductively coupled plasma optical emission spectrometry (ICP-OES) are analyzed to prove the mechanism of perovskite film formation with alkali metal halides.

• Journal of Pharmaceutical Investigation
• /
• v.22 no.4
• /
• pp.267-279
• /
• 1992

Microencapsulations of amoxicillin and cephalexin, using Eudragit RS, RL, E, S and L were investigated. The microcapsules were prepared by the solvent evaporation process in liquid paraffin phase, which is based on dispersion of acetone/isopropanol containing the drug in liquid paraffin. Aluminium tristearate was used as an additive for the preparation of microcapsules. The size distribution, dissolution test and observation by SEM were examined. Good reproducibility in microcapsule preparation was observed. The microcapsules obtained were spherical and free-flowing particles. The dissolution rates of amoxicillin and cephalexin from the microcapsules were considerably decreased as compared with those from amoxicillin and cephalexin powder, respectively. As the dispersing agents (aluminium tristearate) increased, the particle size of microcapsules decreased and the dissolution rate increased. In order to control the release rate of drugs, microcapsules were prepared by mixing Eudragit RS/RL or Eudragit S/L. As Eudragit RL ratio in microcapsule of Eudragit RS/RL increased, the dissolution rate increased. As Eudragit L ratio in microcapsule of Eudragit S/L increased, the dissolution rate increased. Furthermore, the release rates of drugs from Eudragit RS/L or RS/polyelthylene glycol 1540 (PEG 1540) were examined. The dissolution rate of drugs increased with increasing of Eudragit L or PEG 1540 ratio. In conclusion, the release rates of drugs from Eudragit RS/RL or RS/PEG 1540 microcapsule could be controlled, and these microcapsules will be convenient for reducing frequency of administration.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.379-383
• /
• 2011

This paper presents the synthesis of one-dimensional spinel $LiMn_2O_4$ nanostructures using a facile and scalable two-step process. $LiMn_2O_4$ nanorods with average diameter of 100 nm and length of 1.5 ${\mu}m$ have been prepared by solid-state lithiation of hydrothermally synthesized ${\beta}$-$MnO_2$ nanorods. $LiMn_2O_4$ nanowires with diameter of 10 nm and length of several micrometers have been fabricated via solid-state lithiation of ${\beta}$-$MnO_2$ nanowires. The precursors have been lithiated with LiOH and reaction temperature and pressure have been controlled. The complete structural transformation to cubic phase and the maintenance of 1-D nanostructure morphology have been evaluated by XRD, SEM, and TEM analysis. The size distribution of the spinel $LiMn_2O_4$ nanorods/wires has been similar to the $MnO_2$ precursors. By control of reaction pressure, cubic 1-D spinel $LiMn_2O_4$ nanostructures have been fabricated from tetragonal $MnO_2$ precursors even below $500^{\circ}C$.

• Journal of Power Electronics
• /
• v.18 no.1
• /
• pp.300-308
• /
• 2018

An online estimation method for wireless power transfer (WPT) systems is presented without using any measurement of the secondary side or the load. This parameter estimation method can be applied with a controlling strategy that removes both the receiving terminal controller and the wireless communication. This improves the reliability of the system while reducing its costs and size. In a wireless power transfer system with an LCCL impedance matching circuit under a rectifier load, the actual load value, voltage/current and mutual inductance can be reflected through reflected impedance measuring at the primary side. The proposed method can calculate the phase angle tangent value of the secondary loop circuit impedance via the reflected impedance, which is unrelated to the mutual inductance. Then the load value can be determined based on the relationships between the load value and the secondary loop impedance. After that, the mutual inductance and transfer efficiency can be computed. According to the primary side voltage and current, the load voltage and current can also be detected in real-time. Experiments have verified that high estimation accuracy can be achieved with the proposed method. A single-controller based on the proposed parameter estimation method is established to achieve constant current control over a WPT system.

• Journal of the Korea Concrete Institute
• /
• v.27 no.4
• /
• pp.443-450
• /
• 2015

This paper presents an investigation of the mechanical and microstructural properties of Class F fly ash based geopolymer containing sodium sulfate as an additive. Sodium sulfate was used as an chemical additive at the dosage levels of 0, 2, 4, and 6wt% of fly ash. Sodium hydroxide and sodium silicate solutions were used to activate fly ash. The compressive strengths of geopolymer pastes were measured at the age of 28 days. The microstructures of the geopolymer pastes were examined using XRD, MIP and SEM tests. The additions of 2wt% and 4wt% sodium sulfate produced geopolymers with high strength, while increasing the dosage of levels to 6% resulted in almost no changes in strength, comparing with the control geopolymer. The optimum increase in strength was obtained with the addition of 4wt% sodium sulfate. As the amount of sodium sulfate is increased, no additional crystalline phase was detected and no change of amorphous phase indicated despite the change in the strength development. The increase in the strength was due to the change of pore size distribution in samples. As addition of sodium sulfate altered the morphologies of reactive productions and Si/Al ratios of the reaction products, the strengths were thus affected. It was found that the strengths of geopolymer were larger for lower Si/Al ratios of reaction products formed in samples. The optimal amount of sodium sulfate in the fly ash based geopolymer helps to improve mechanical properties of the geopolymer, on the other hand, the high percentage of sodium sulfate could exist as an impurity in the geopolymer and hinder the geopolymer reaction.

• Polymer(Korea)
• /
• v.27 no.4
• /
• pp.370-376
• /
• 2003

Poly(DL-lactide-co-glycolide) nanoparticles were prepared by the modified spontaneous emulsification solvent diffusion method. Polymer solution was prepared by two water-soluble organic solvents, such as ethanol and acetone. Because of its biocompatible nature, PEG-PPG diblock copolymer was used as surfactant and stabilizer. The influence of several preparative variables on the nanoparticle formation, such as type and concentration of stabilizing agent, stirring methods, water/oil phase ratio and polymer concentration were investigated in order to control and optimize the process. After preparation of nanoparticles, particle size and distribution were evaluated by the light scattering particle analyzer. As results, the particle size was 50-200 nm and dispersibility was monodisperse. It was found that the appropriate selections of binary solvent mixtures and polymeric concentrations in both organic and aqueous phases could provide a good yield and favorable physical properties of PLGA nanoparticles.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.20 no.3
• /
• pp.177-184
• /
• 1987

The quantitative mechanics on the sideways walking of the crabs may provide a basic solution for entanglements of the walking legs in gillnets. The gaiting behaviour of the crabs on the flat board and the nettings 10, 16 and 23 mm in mesh size were experimented concerning about stepping positions and times in the laboratory using video set on July, 1984, It was found that the irregular movements of walking crabs in stepping positions and patterns were appeared on the nettings due to the absence of mechanical contact in spite of neural control of compensating, while on the flat surface evolved systematic leg movements. The mean stride length and walking velocity, which were increased with the carapace width on the flat board, as well as the step period and forward by backward stroke time were greater than those values on the netting, not associated with the carapace or the mesh size. Also, the step period and the Phase difference on the nettings revealed larger fluctuation than on the flat board. The joint angles of the walking legs, on the nettings in meropodite-carporodite and thorax-meropodite, which joint was varied especially up to below horizon because of the falling legs through the netting twine, were virtually wider than those on the flat substrate.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.553-558
• /
• 2003

The boundary estimation problem is used to estimate the shape of organic depend on the phase of the cardiac cycle or interested in the detection of the location and size of anomalies with resistivity values different from the background tissues such as nuclear reactor. And we can use the method to solve the optimal solution such as modified Newton raphson, kalman filter, extended kalman filter, etc. But, this method consumes much time and is sensitive to the initial value and noise in the estimation of the unknown shape. In the paper, we propose that multi-layer neural networks estimate the boundary of the unknown object using Fourier coefficient. This method can be used at the real time estimation and have strong characteristics at the noise and initial value. It uses voltage change; difference the homogeneous voltage to the non-homogeneous voltage, and change of Fourier coefficient change to train multi-layer neural network. After train, we can have real time estimation using this method.

• Progress in Superconductivity and Cryogenics
• /
• v.9 no.4
• /
• pp.24-27
• /
• 2007

The purpose of this work is to develop, integrate, and implement an optical characterization method to evaluate physical properties in coated conductors and investigate the local distribution of the causes of degraded performance. The method that we selected at this moment is Raman scattering spectroscopy, which is accompanied with measurements of local supercurrent transport, phase composition, microstructure, and epitaxy quality for coated conductors that range in size up to multi-meter-length tapes and that embrace the entire tape embodiment (substrate through cap layer). The establishment of Raman spectroscopy as an on-line process monitoring tool is our eventual goal of research, but it requires very robust and cost-effective equipments. We analyzed $YBa_2Cu_3O_7(YBCO)$ thin films grown at various substrate temperatures by using Raman spectroscopy. YBCO films were grown by a high-rate electron-beam co-evaporation method. Raman spectra of YBCO films with lower-transport properties exhibit additional phonon modes at ${\sim}300cm^{-1}$, ${\sim}600cm^{-1}$ and ${\sim}630cm^{-1}$, which are related to second-phases such as $Ba_2Cu_3O_{5.9}$ and $BaCuO_2$. We propose a new method to characterize Raman spectra of coated conductors for an in-line quality control.