• Composites Research
• /
• v.32 no.6
• /
• pp.382-387
• /
• 2019

A single frequency strain mode test, a stress relaxation mode test, and a creep test using RH-DMA were performed to investigate the effects of relative humidity and temperature on the viscous properties of PET film. The relative humidity was 10%, 30%, 50%, 70%, and 90%. The temperature was considered to be 30~95℃ for single frequency strain mode tests, 30℃ and 70℃ for stress relaxation mode test, and 5~95℃ for creep test. According to the results, higher relative humidity results in lower storage modulus and loss modulus, but the maximum value of the loss modulus is not significantly affected by changes in relative humidity and is almost constant. Relaxation modulus decreases rapidly at the beginning and becomes constant, and as the temperature increases, it is susceptible to changes in relative humidity. Strain recovery also increases rapidly at the beginning and is susceptible to changes in relative humidity as the temperature increases. In addition, as the temperature increases, the degree of increase in creep compliance increases, and as the temperature rises above the glass transfer temperature, the degree of increase becomes very large. The master curve determined by the time-temperature superposition provides the information to predict the long-term performance under operating conditions such as relative humidity and temperature.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.29 no.3
• /
• pp.17-30
• /
• 2011

The polarizer is an important optical element used in a variety of applications. Nano-wire grid polarizers in the form of sub-wavelength metallic gratings are an attractive alternative to conventional polarizers, because they provide high extinction ratio. This study has been carried out to fabrication of the 17inch area size nano-wire grid polarizer(NWGP) The master for NWGPs with a pitch of 200nm and the area size $730mm{\times}450mm$ were fabricated using laser interference lithography and aluminum sputtering and wet etching. And The NWGP fabrication process was using by the Roll to-Roll UV imprinting and was applied to flexible PET film. The results were a transmission of light (Tp) 46.7%, reflectance (Rs) 40.1% and Extinction ratio of above 16 for the visible light range.

• Proceedings of the Korea Contents Association Conference
• /
• 2009.05a
• /
• pp.175-178
• /
• 2009

In this paper, we describe about interactive electronic book utilizing tabletop display interface and digi-pet. Because of this system can define a lot of gestures using touch point of finger, help that user experiences electronic book effectively more than existent input device. Also, support 1 users in 1 input device in existent mode, but this system can expect various effect because support Multi-user. The digi-pet(digital pet) is physical tools that convey emotion between tabletop display platform and user. And this shows various results acting as assistance because becomes master of story of imagination and participate directly on talk and makes change of story. In this paper, we described about oriented electronic book system the future that combines tabletop display and Digi-pet. This system is expected that the usefulness is increased by leaps and bounds along with technology development forward.

• The Korean Journal of Nuclear Medicine
• /
• v.38 no.5
• /
• pp.338-343
• /
• 2004

Purpose: The purpose of this study was to develop a small animal PET using dual layer phoswich detector to minimize parallax error that degrades spatial resolution at the outer part of field-of-view (FOV). Materials and Methods: A simulation tool GATE (Geant4 Application for Tomographic Emission) was used to derive optimal parameters of small PET, and PET was developed employing the parameters. Lutetium Oxyorthosilicate (LSO) and Lutetium-Yttrium Aluminate-Perovskite(LuYAP) was used to construct dual layer phoswitch crystal. $8{\times}8$ arrays of LSO and LuYAP pixels, $2mm{\times}2mm{\times}8mm$ in size, were coupled to a 64-channel position sensitive photomultiplier tube. The system consisted of 16 detector modules arranged to one ring configuration (ring inner diameter 10 cm, FOV of 8 cm). The data from phoswich detector modules were fed into an ADC board in the data acquisition and preprocessing PC via sockets, decoder block, FPGA board, and bus board. These were linked to the master PC that stored the events data on hard disk. Results: In a preliminary test of the system, reconstructed images were obtained by using a pair of detectors and sensitivity and spatial resolution were measured. Spatial resolution was 2.3 mm FWHM and sensitivity was 10.9 $cps/{\mu}Ci$ at the center of FOV. Conclusion: The radioactivity distribution patterns were accurately represented in sinograms and images obtained by PET with a pair of detectors. These preliminary results indicate that it is promising to develop a high performance small animal PET.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.9
• /
• pp.722-727
• /
• 2013

Medical treatment for animals is very difficult as the opinions of pets' masters take priority over treatment regardless of the seriousness of pets' disease or the needs of medical treatment. In case that a pet has heart disease, especially, it is difficult to get the direct answer from the pet's master on the decision or confirmation of treatment. For those reasons, it is almost impossible to predict and treat the pet before an emergency like the heart failure or an unexpected death happens. Using stethoscope can be the first diagnosis method to check the heart or any kinds of disease inside the body. High-tech equipments like CT, X-ray or Ultrasound can be used, but they can only be used as a second choice of diagnosis method since it requires professional skills and its high price. That's why stethoscope is still the best diagnostic tool when one makes the first diagnosis. In this study, we give a detailed account of digital diagnosis system in which veterinarians can analyze the sound from stethoscope without bringing it to their ears and make a diagnosis wherever they are. And we suggest a new concept of diagnosis system surrounding, which shows the relativeness of disease through Level Crossing Rate(LCR) and energy level from the stethoscope sound made in this system.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2011.03a
• /
• pp.86-86
• /
• 2011

나노소재기술은 기존 소재로는 얻을 수 없는 새로운 기능 및 특성을 나타낼 수 있어 산업전반에 적용할 수 있는 최첨단집적기술이다. 그러나 나노입자를 섬유에 첨가하여 기능성 섬유를 생산하는 경우 응집이 발생하는 등의 다양한 문제점이 발생하는데 이를 극복하기 위해서는 사이즈 분포를 제어하는 기술, 표면처리를 통해 분산성을 향상시키는 기술, 나노입자와 섬유와의 상용성을 개선하는 기술 등이 해결되어야 한다. 본 연구에서는 고기능성 및 고부가가치 경편파일 니트 원단을 개발하기 위해 은(Silver) 나노입자가 균일하게 분산된 M/B(Master Batch)를 제조하였으며, 이를 PET와의 용융 혼합 방사함으로써 0.5denier(75D/144F)급 원사에 99.9%의 영구적인 항균/소취 기능을 부여하였다. 또한 개발된 극세사를 이용하여 다양한 경편파일 원단을 설계하고, 기모, 염색 및 날염 등의 공정을 거쳐 나노기술융합형 화학섬유소재를 이용한 기능성 침장 제품을 개발하였다.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1833-1836
• /
• 2008

Recently as the micro surface features become higher and diverse in their shapes, the releasing of the molded features becomes more crucial for manufacturing of the micro patterned products. The higher aspect ratio of the features or more complex shape of the features results in larger releasing force, elongation or cohesive failure of the features during the releasing. Another issue would be the uniformity of the released surface features after molding, especially for applications with large area surface. The micro patterned optical film, one of typical applications for micro surface features, consists of two layers, the thermoplastic base film and the micro formed UV resin layer. Therefore two interfaces are typically involved during the forming of this micro featured film; one is between the base film and the UV resin and another is between the resin and the pattern master. To improve the releasing of the molded surface features, the adhesive characteristic was investigated at these two interfaces. A PET film was used as a base film and two UV curable resins with different surface energy were prepared for different adhesiveness. Also the two different pattern masters were employed; one is made from brass-copper alloy and fabricated with PMMA. The adhesiveness at each interface was measured for some combinations of these base film, UV resins and the masters and the effect of this adhesiveness on the releasing was investigated.