• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.2
• /
• pp.585-594
• /
• 2013

In this study, laboratory experiments and numerical simulations were conducted to test the performance of resonance power buoy system proposed by Kweon et al.(2010). The system is composed of a linear generator and a mooring buoy. The mover of the linear generator mainly has heave motion driven by vertical oscillation of the buoy. In this system, the velocity discrepancy between the mover and the buoy makes electricity. However, ocean wave energy as a natural resource around Korean peninsula is comparatively small and the driving force for producing electricity is not enough for commercialization. Therefore, it is necessary that the buoy motion be amplified by using resonance characteristics. In order to verify the resonance effects on the test power buoy, the experimental investigations were conducted in the large wave flume (length of 110 m, width of 8 m, maximum depth of 6 m) equipped with regular and random plunger wave generator. The resonance draft of test power buoy is designed for the corresponding period of incident wave, 1.96 sec. Regular wave test results show that the heave response amplitude operator(RAO) by a test buoy has the amplification of 5.66 times higher compared to the wave amplitude at the resonance period. Test results of random waves show that the buoy has the largest spectrum area of 20.73 times higher at the point of not the resonance period but the shorter one of 1.85 sec. Therefore this study suggests the resonance power buoy for wave power generation for commercial application in the case of the coastal and oceanic area with smaller wave energy.

• Journal of Advanced Navigation Technology
• /
• v.25 no.1
• /
• pp.68-77
• /
• 2021

In this paper, a GPS/MEMS IMU integrated navigation receiver module capable of operating in a high dynamic environment is designed and fabricated, and the results is confirmed. The designed module is composed of RF receiver unit, inertial measurement unit, signal processing unit, correlator, and navigation S/W. The RF receiver performs the functions of low noise amplification, frequency conversion, filtering, and automatic gain control. The inertial measurement unit collects measurement data from a MEMS class IMU applied with a 3-axis gyroscope, accelerometer, and geomagnetic sensor. In addition, it provides an interface to transmit to the navigation S/W. The signal processing unit and the correlator is implemented with FPGA logic to perform filtering and corrrelation value calculation. Navigation S/W is implemented using the internal CPU of the FPGA. The size of the manufactured module is 95.0×85.0×.12.5mm, the weight is 110g, and the navigation accuracy performance within the specification is confirmed in an environment of 1200m/s and acceleration of 10g.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.26 no.3
• /
• pp.29-38
• /
• 2022

In this study, the shaking table tests were carried out on six types of non-structural elements installed on a full-scale two-story steel structure. The shaking table tests were performed for non-structural elements with and without seismic isolators. In this study, the seismic performance of Uninterruptible Power Supply (UPS) specimens was tested and investigated. Non-seismic details were composed of conventional channel section steel beams, and the seismic isolators were composed of high damping rubber bearing (HDRB) and wire isolator. The input acceleration time histories were artificially generated to satisfy the requirements proposed by the ICC-ES AC156 code. Based on the test results, the damage and dynamic characteristics of the UPS with the seismic isolator were investigated in terms of the natural frequency, damping ratio, acceleration time history responses, dynamic amplification factors, and relative displacements. The results from the shaking table showed that the dynamic characteristics of the UPS including the acceleration response were significantly improved when using the seismic isolator.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.35 no.6
• /
• pp.375-380
• /
• 2022

High-speed railway bridges carry a risk of dynamic response amplification due to resonance caused by train loads, and running safety and riding comfort must therefore be reviewed through dynamic analysis in accordance with design codes. The running safety and ride comfort calculation procedure, however, is time consuming and expensive because dynamic analyses must be performed for every 10 km/h interval up to 110% of the design speed, including the critical speed for each train type. In this paper, a deep-learning-based prediction system that can predict the running safety and ride comfort in advance is proposed. The system does not use dynamic analysis but employs a deep learning algorithm. The proposed system is based on a neural network trained on the dynamic analysis results of each train and speed of the railway bridge and can predict the running safety and ride comfort according to input parameters such as train speed and bridge characteristics. To confirm the performance of the proposed system, running safety and riding comfort are predicted for a single span, straight simple beam bridge. Our results confirm that the deck vertical displacement and deck vertical acceleration for calculating running safety and riding comfort can be predicted with high accuracy.

• Food Science and Preservation
• /
• v.30 no.3
• /
• pp.483-491
• /
• 2023

This study aimed to compare the bioactive compounds in Centella asiatica (C. asiatica) cultivated in a smart farm and a field and their effects on human keratinocyte cells. C. asiatica was collected in Jeju-do, Korea, and cultured in a smart farm and a field. The main bioactive compounds in the two differentially cultured C. asiatica were identified, and their activation in keratinocytes were assessed. Amplification and sequencing of the internal transcribed spacer (ITS) DNA in the nucleus and psbA-H DNA in the chloroplast were performed for species analysis. A comparison of DNA of plants reported in the NCBI GenBank was performed. The ITS DNA and psbA-H DNA sequences of C. asiatica cultivated in a smart farm and a field were consistent with No. MH768338.1 and No. JQ425422.1, respectively. Analysis of the triterpenes was performed using high performance liquid chromatography (HPLC) and as a result, C. asiatica cultured in a smart farm had more triterpenes than those cultured in a field. The effects of C. asiatica grown in a smart farm on cell proliferation and scratch recovery in HaCaT cells were greater than those grown in a field. These results suggest that C. asiatica cultivated in a smart farm can be effectively utilized as a health functional food.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.4
• /
• pp.9-21
• /
• 2008

In this paper, we propose a GNSS-based RF receiver, A high precision localization architecture, and a high sensitivity localization architecture in order to solve the satellite navigation system's problem mentioned above. The GNSS-based RF receiver model should have the structure to simultaneously receive both the conventional GPS and navigation information data of future-usable Galileo. As a result, it is constructed as the multi-band which can receive at the same time Ll band (1575.42MHz) of GPS and El band (1575.42MHz), E5A band (1207.1MHz), and E4B band (1176.45MHz) of Galileo This high precision localization architecture proposes a delay lock loop with the structure of Early_early code, Early_late code, Prompt code, Late_early code, and Late_late code other than Early code, Prompt code, and Late code which a previous delay lock loop structure has. As we suggest the delay lock loop structure of 1/4chips spacing, we successfully deal with the synchronization problem with the C/A code derived from inaccuracy of the signal received from the satellite navigation system. The synchronization problem with the C/A code causes an acquisition delay time problem of the vehicle navigation system and leads to performance reduction of the receiver. In addition, as this high sensitivity localization architecture is designed as an asymmetry structure using 20 correlators, maximizes reception amplification factor, and minimizes noise, it improves a reception rate. Satellite navigation system repeatedly transmits the same C/A code 20 times. Consequently, we propose a structure which can use all of the same C/A code. Since this has an adaptive structure and can limit(offer) the number of the correlator according to the nearby environment, it can reduce unnecessary delay time of the system. With the use of this structure, we can lower the acquisition delay time and guarantee the continuity of tracking.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.5
• /
• pp.25-33
• /
• 2011

This work proposes a skinny-type 10b 50MS/s 0.13um CMOS three-step pipeline ADC for CIS applications. Analog circuits for CIS applications commonly employ a high supply voltage to acquire a sufficiently acceptable dynamic range, while digital circuits use a low supply voltage to minimize power consumption. The proposed ADC converts analog signals in a wide-swing range to low voltage-based digital data using both of the two supply voltages. An op-amp sharing technique employed in residue amplifiers properly controls currents depending on the amplification mode of each pipeline stage, optimizes the performance of op-amps, and improves the power efficiency. In three FLASH ADCs, the number of input stages are reduced in half by the interpolation technique while each comparator consists of only a latch with low kick-back noise based on pull-down switches to separate the input nodes and output nodes. Reference circuits achieve a required settling time only with on-chip low-power drivers and digital correction logic has two kinds of level shifter depending on signal-voltage levels to be processed. The prototype ADC in a 0.13um CMOS to support 0.35um thick-gate-oxide transistors demonstrates the measured DNL and INL within 0.42LSB and 1.19LSB, respectively. The ADC shows a maximum SNDR of 55.4dB and a maximum SFDR of 68.7dB at 50MS/s, respectively. The ADC with an active die area of 0.53$mm^2$ consumes 15.6mW at 50MS/s with an analog voltage of 2.0V and two digital voltages of 2.8V ($=D_H$) and 1.2V ($=D_L$).

• Food Science of Animal Resources
• /
• v.29 no.1
• /
• pp.108-113
• /
• 2009

Apolipoprotein E (APOE) is a plasma lipoprotein in mammals and plays an important role in the transport and metabolism of lipids such as phospholipids and triglycerides. Therefore, the APOE gene could be a candidate gene controlling lipid metabolism in beef cattle. This study was performed to identify single nucleotide polymorphisms (SNP) in the APOE gene and to investigate the effects of SNP genotype on the carcass traits such as meat quantity and quality in Korean cattle. For PCR amplification, pooled DNA made from unrelated 60 individuals was prepared and primer pairs were designed based on the cDNA sequence of exon 4 region of the bovine APOE gene. A SNP was identified at position 2034 (T/C substitution) of the exon 4 region in the APOE gene. PCR-RFLP procedure with restriction enzyme ACC I was developed for determining the SNP genotype for each of a total of 309 animals with pedigree information and performance records through the national progeny testing program. The frequencies of the genotypes TT, TC and CC were 10.9, 46.9 and 42.2%. Gene frequencies were 0.344 for T allele and 0.656 for C allele. The g.2034T>C SNP genotype showed a significant effect (p<0.05) on dressing percentage and meat color, respectively. Animals with the TT genotype showed higher dressing percentage than those with the CC genotype, and TT genotype had desirable meat color compared with CC genotype. These results suggest that the g.2034T>C SNP genotype of the APOE gene may be useful as a DNA marker for meat quantity index and dressing percentage in Korean cattle.

• Journal of Life Science
• /
• v.27 no.11
• /
• pp.1276-1289
• /
• 2017

This study isolated and purified the antimicrobial peptide McSSP-31 from an acidified hemocyte extract of a Mytilus coruscus. The antimicrobial peptide was purified by using a $C_{18}$ reversed-phase high-performance liquid chromatography (HPLC). The peptide was determined to be 3330.549 Da by matrix assisted-laser desorption ionization time-of-flight mass spectrophotometer (MALDI-TOF/MS). The N-terminus of a 14 amino-acid sequence was identified as P-S-P-T-R-R-S-T-S-R-S-K-S-R by Edman degradation method. The acquired sequence showed a 93% similarity with the sperm-specific protein Phi-1, which is from M. californianus. The identified open-reading frame (ORF) of peptide was 306 bp encoding 101 amino acids, which was analyzed by rapid amplification of cDNA ends (RACE), cloning and sequencing analysis. We compared the full sequence with other known proteins that reveal the sperm-specific protein Phi-1 (93.5%) of M. californianus. Synthesized antimicrobial peptide (McSSP-31) showed antibacterial activity against gram-positive bacteria including B. subtilis, S. mutans, S. aureus and gram-negative bacteria including E. coli, K. pneumoniae, P. mirabilis, P. aeruginosa and fungi, C. albicans. Also, synthesized peptide showed strong antibacterial activity against antibiotic-resistant strains, including S. aureus. The cytotoxicity of the peptide was determined by using the HUVEC human cell line. The peptide did not exhibit any significant cytotoxic effects on the normal human cell line, and it had very low hemolytic activity with flounder hemoglobin. The results demonstrated that peptide purified from the hemocyte of a M. coruscus exhibits antibacterial activity against various bacteria and has the potential to be an alternative antibiotic agent.

• Annals of Clinical Microbiology
• /
• v.21 no.4
• /
• pp.86-91
• /
• 2018

Background: The PANA RealTyper HPV kit (PANAGENE, Korea; PANA RealTyper) was developed to genotype human papillomavirus (HPV) and was based on multiplex real-time PCR amplification and melting curve analysis. In this study, we compared PANA RealTyper to the AdvanSure HPV GenoBlot assay (LG Life Sciences, Korea; AdvanSure assay) and attempted to evaluate the performance of PANA RealTyper. Methods: A total of 60 cervical specimens were collected from women undergoing routine cervical cancer screening. The AdvanSure assay and PANA RealTyper kit identified the same 20 high-risk genotypes. However, the AdvanSure assay identified 15 low-risk genotypes, while the PANA RealTyper kit identified only 2 but detected 18 low-risk genotypes. Results: Among the total 60 specimens, 54 high-risk genotypes (40 specimens) and 20 low-risk genotypes (18 specimens) were detected. The agreement rates of the assays ranged from 94.4 to 100% for high-risk genotypes. Among 9 genotypes that were positive in the PANA RealTyper kit but negative in the AdvanSure assay, 7 were confirmed as true positive (HPV genotypes 16 (n=1), 39 (n=1), 52 (n=1), 58 (n=2), 68 (n=2)). Among 4 genotypes that were negative in the PANA RealTyper kit but positive in the AdvanSure assay, 3 were confirmed as HPV genotype 59. Among the 19 low-risk genotypes positive in the AdvanSure assay, there were 2 cases of HPV 6 and 1 case of HPV 11. In comparison, only 1 positive case of HPV 6 was determined by the PANA RealTyper kit. Conclusion: The PANA RealTyper kit was comparable with the AdvanSure assay. The PANA RealTyper kit would be useful and suitable for HPV genotyping in the clinical laboratory.