• Journal of Welding and Joining
• /
• v.33 no.5
• /
• pp.47-52
• /
• 2015

In this study, it was tried to analyze the effects of welding parameters on the weld penetration and aspect ratio when a STS316L pipe was welded in a horizontal position by GTAW. Experiments were systematically designed using a L18 orthogonal array, and the effects of welding parameters were statistically analyzed by ANOVA(Analysis of Variance). The shielding gas type has the largest effect on both the penetration and aspect ratio. The welding current type and shielding gas flow rate have a little effect on the penetration, whereas the electrode tip angle has a little effect on the aspect ratio. When welded at a selected welding condition, which is composed of He shielding gas, pulse current of 300/45 A, electrode tip angle of 90o, and shielding gas flow rate of 30 l/min, the estimated interval at least 95 % confidence was $1.99{\pm}0.18mm$ for the penetration and $0.31{\pm}0.04$ for the aspect ratio. From the confirmation experiments, the average penetration and aspect ratio were well agreed with the estimation as 1.96 mm and 0.30, respectively. Additionally, the effects of the welding speed and welding current on the penetration and aspect ratio were experimented and analyzed by linear regression. The penetration was linearly increased with the decrease of the welding speed and with the increase of the welding current, but the aspect ratio showed a tendency to a little decrease with the increase of both the welding speed and current.

• Journal of Welding and Joining
• /
• v.26 no.6
• /
• pp.42-47
• /
• 2008

TIG welding enables to produce high quality weldment. However it has some problems such as shallow penetration and large distortion due to low penetration aspect ratio after welding. In order to overcome those problems, there are many ongoing studies on A-TIG welding, which use active flux. In this study, the effect of arc length and shield gas on penetration aspect ratio with melt-run welding on STS 304 6t, on which active flux was spreaded, was investigated. Arc length was changed from 1mm to 3mm, and aspect ratio became higher as arc length was decreased in this range. 100% Ar gas, Ar-$H_2$ mixed gas, Ar-He mixed gas, and 100% He gas were used as shield gas in this study. When Ar-$H_2$ mixed gas, Ar-He mixed gas, and 100% He gas were applied, penetration and melting efficiency were both increased as compared with 100% Ar gas. Aspect ratio was the highest with Ar-2.5% $H_2$ mixed gas.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.18 no.2
• /
• pp.154-159
• /
• 2015

This paper deals with the effect of concrete target size on penetration of projectiles. We investigated the penetration depth and residual velocity of projectiles using the 2-D axial symmetric model. Most analysis were conducted with 13 kg projectile (striking velocity: 456.4 m/s) and concrete target with compressive strength of 39 MPa. This paper provided penetration depth (or residual velocity) versus ratio D/d (target diameter, D and projectile diameter, d). When the bottom of concrete cylinder was constrained, penetration depth converged to limit depth more than the ratio D/d of 36. The residual velocity of projectile with thin concrete target were investigated. The residual velocity was converged to specific velocity more than the ratio D/d of 16.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.34 no.3
• /
• pp.25-31
• /
• 2002

The purpose of this study was to analyze how the fiber properties and mixing ratio of softwood and hardwood pulp affect on roundness of printed image. Softwood pulp and hardwood pulp were refined to 400 and 600ml CSF by Valley beater and handsheets of 70 g/$m^2$ basis weight were made at different mixing ratios of hardwood and softwood pulp. The roundness, dot area, and shape of the printed dot were measured by Image Analyzer. The depths and shapes of the acridine orange penetration into paper were measured by CLSM. With higher mixing ratio of hardwood pulp, the paper showed higher air-permeability and better formation, especially at lower freeness. The roundness of the printed image became better and the dot size became smaller when the amount of hardwood pulp increased. Penetration depth of acridine orange by CLSM became greater and roundness increased to real circle when the amount of hardwood pulp increased. It was thought that higher mixing ratio of hardwood fibers resulted in efficient penetration by better formation with uniform micro-pore distribution and it increased roundness. It was thought that fiber properties and mixing ratio affected the structure of paper and the shape of the printed dot. This study showed that the measurement of depth of the liquid penetration into paper without destruction and contact was feasible. Moreover, this method showed that the shape of the liquid penetration was measurable.

• Restorative Dentistry and Endodontics
• /
• v.1 no.1
• /
• pp.11-17
• /
• 1975

This study is to determine the penetration of various medicaments such as Howe's ammoniacal silver nitrate and methyleneblue, to root canal dentin within given time (5,10,30 sec.) Followings are the results obtained from this study. 1) The dye stuff is more deeply penetrated according to the time elapsed. 2) According to the increase of age, the penetration ratio is decreased accordingly. 3) The penetration ratio of Howe's ammoniacal silver nitrate is higher than that of methyleneblue. 4) The permeability of the root canal dentin is gradually reduced as access to the apex.

• Geomechanics and Engineering
• /
• v.9 no.6
• /
• pp.743-755
• /
• 2015

It is well known that the quality of sample significantly determines the accuracy of soil parameters for laboratory testing. Although sampling disturbance has been studied over the last few decades, the theoretical investigation of soil disturbance due to sampling penetration has been rarely reported. In this paper, an analytical solution for estimating the soil disturbance due to sampling penetration was presented using cavity expansion method. Analytical results in several cases reveal that the soil at different location along the sample centerline experiences distinct phases of strain during the process of sampling penetration. The magnitude of induced strain is dependent on the position of the soil element within the sampler and the sampler geometry expressed as diameter-thickness ratio D/t and length-diameter ratio L/D. Effects of sampler features on soil disturbance were also studied. It is found that the induced maximum strain decreases exponentially with increasing diameter-thickness ratio, indicating that the sampling disturbance will reduce with increasing diameter or decreasing wall thickness of sampler. It is also found that a large length-diameter ratio does not necessarily reduce the disturbance. An optimal length-diameter ratio is suggested for the further design of improved sampler in this study.

• Korean Journal of Computational Design and Engineering
• /
• v.18 no.5
• /
• pp.367-373
• /
• 2013

In this study, the penetration characteristic from the cubic and cylindrical penetrator consisting of tungsten material with the velocity of 2,300 m/s is evaluated and the penetration possibility into the target is confirmed. The design of shape and size of penetrator is directly related to space and weight of the warhead. AUTODYN-3D simulation is used to study the penetration effect of penetrator. The purpose of numerical analysis is to verify the penetration characteristic with various L/D penetrator. The penetration performance of penetrator with identical weight due to the shape is also confirmed. The cylindrical and cubic penetrator has enough penetration energy on constant target body. Because the possibility of 2'nd penetration is important factor after 1'st penetration into target body, residual velocity of residual mass must be existed as much as possible. As geometrical shape ratio increases, penetration performance is confirmed to improve.

• Journal of the Korean Institute of Gas
• /
• v.4 no.1 s.9
• /
• pp.33-39
• /
• 2000

Stress intensity factor after penetration was discussed experimentally using long surface pre-cracked specimens of aluminum alloy 5083. The propagation behavior evaluation of long surface crack by equation proposed at penetration of short surface crack could be need modification to evaluate precisely because the error was high as aspect ratio is little. The modification of stress intensity factor with consideration of aspect ratio at penetration of long surface crack can be analyzed the behavior of crack penetration quantitatively.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 1996.04a
• /
• pp.333-336
• /
• 1996

This paper is an exploratory study aimed at finding factors that influence the penetration of cellular mobile telecommunications which have seen rapid development since 1980s. The paper tries to find economy and policy variables to influence the penetration by means of the multiple regression analysis. This paper shows a model that explain the penetration ratio of cellular service. The model is based on data from 39 upper middle income and 39 high income countries. The result shows that GDP per capita and the service period of the cellular mobile telecommunication have influenced on the penetration ratio positively, and the tariff of the service negatively. But, it is the open area to study the impact of the telecommunications policy changes on penetration, and to set a model which could explain the nation-specific characteristics.

• Journal of Construction Engineering and Project Management
• /
• v.7 no.1
• /
• pp.26-29
• /
• 2017

This paper represents the experimental investigation of chloride penetration into plain concretes and reinforced concretes. The main objective of this work is to study the main influencing parameters affecting corrosion of steel in concrete. Plain cement concrete and reinforced cement concrete with different water-cement ratios and different cover depth were subjected to ponding test. Ponding of specimens were done for different periods into 10% NaCl solution. Depth of penetration of chloride solution into specimens was measured after ponding. Specimens were crushed and reinforcements were washed using $HNO_3$ solution and weight loss due to corrosion was calculated accordingly. There was a linear relationship between depth of penetration and water-cement ratio. It was also observed that, corrosion of reinforcing steel increases with chloride ponding period and with water-cement ratio. Corrosion of steel in concrete can be minimized by providing good quality concrete and sufficient concrete cover over the reinforcing bars. Water-cement ratio has to be low enough to slow down the penetration of chloride salts into concrete.