• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.249-252
• /
• 2002

we have studied the characteristics of PHEMT's with gate recess etching method. The DC characterization of PHTMT fabricated with the wide single recess methods is a maximum drain current density of 319.4 ㎃/mm and a peak transconductance of 336.7 ㎳/mm. The RF measurements were obtained in the frequency range of 1~50GHz. At 50GHz, 3.69dB of 521 gain were obtained and a current gain cut-off frequency(f$_{T}$) of 113 CH and a maximum frequency of oscillation(f$_{max}$) of 172 Ghz were achieved from this device. On the other hand, a maximum drain current of 367 mA/mm, a peak transconduclancc of 504.6 mS/mm, S$_{21}$ gain of 2.94 dB, a current gain cut-off frequency(f$_{T}$) of 101 CH and a maximum frequency of oscillation(f$_{max}$) of 113 fa were achieved from the PHEMT's fabricated by the .narrow single recess methods.methods.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.04a
• /
• pp.188-191
• /
• 2001

Generally, main factors of tool damage are cutting speed, feed rate and depth of cut. The increase of those factors can cause tool breakage or worsen product quality such as machining accuracy deterioration. Those three factors are concerned with cutting force. Cutting force reaches at its maximum value when cutter blade cuts away the object directly, and it is the time when tool damages are at high probability. In this study, we detect the maximum cutting force affecting tool damage and control the maximum cutting force based on the measured peak force.

• Explosives and Blasting
• /
• v.20 no.2
• /
• pp.7-19
• /
• 2002

The cut is placed high up in the section, the 1st sloping holes below the cut, and divided all the holes located below the 1st sloping holes into a certain area with longitudinal section, to lower pollution made from tunnel blasting. With the sequential blasting machine, after I first blasted holes around the cut holes by a pre-splitting method, blasted the cut area and the 1st sloping holes. The 1st and 2nd sloping holes divided areas are initiated gradually to free face upwards made by the cut. Especially, I pre-splinted contour holes previous blast the before sloping holes from the contours. The ground vibration from the earth surface just over the advance face decreased about 42.0% compare with the down blasting method under the condition of equal charge weight per delay. I controlled the crack and over break of the mother rock by pre-splitting contour holes before blast the first sloping holes from the contours. The peak values of noise and air blast by blasting decreased about 10dB more than the down blasting method. the noise and air blast diminished gradually as a round. The throw distance of the fly rock was decreased about 55%.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.406-410
• /
• 2000

Using the hot-wall epitaxy method, we grew a $Hg_{1-x}Cd_xTe$ (MCT) thin film in-situ after growing (111) CdTe of 9 $mu \textrm{m}$ as a buffer layer. The value of FWHM of double crystal x-ray diffraction rocking curve was 125 arcsec and the surface morphology was clean with a small roughness of 10 nm. From measuring the photocurrent of the grown MCT thin film, the maximum peak wavelength and the cut-off wavelength were 1.1050 $\mu\textrm{m}$ (1.1220 eV) and 1.2632 $\mu\textrm{m}$ (0.9815 eV), respectively. This peak wavelength corresponds to the peak of the band gap due to the intrinsic transition of the photoconductor. Therefore, the MCT thin film could be used as the photoconducting detector sensing a near-IR wavelength band from 1.0 to 1.6 $\mu\textrm{m}$.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.9
• /
• pp.1260-1268
• /
• 2012

Recently, lack of power reserve margin was observed quite often. In this paper, we studied the method to secure power source for a short time, to cut the utility power peak load, and to reduce the users electricity bills. Emergency diesel generator of an office building is to be converted into a dual-fuel engine generator which is responsible for a portion of the peak load. Compared to the conventional diesel fuel generator, the proposed dual-fuel engine is able to reduce the generation power cost by dual-fuel combustion, and it also mitigates the building's utility power peak load by charging the building's peak load. If the dead resources (a group of emergency dual-fuel engine generators), as a Virtual Power Plant, are operating in peak time, we can significantly reduce future large power development costs. We investigated the current general purpose electricity bills as well as the records of the building electric power usage, and calculated diesel engine generator renovation costs, generation fuel costs, driving conditions, and savings in electricity bills. The proposed dual-fuel engine generation method reduces 18.1% of utility power peak load, and turned out to be highly attractive investment alternative which shows more than 27% of IRR, 76 million won of NPV, and 20~53 months of payback periods. The results of this study are expected to be useful to developing the policy & strategy of the energy department.

• Journal of Digital Convergence
• /
• v.12 no.11
• /
• pp.309-316
• /
• 2014

In this paper, we propose an efficient detph map creation method using Graph Cut and Discrete Wavelet Transform. First, we have segmented the original image by using Graph Cut to process with its each areas. After that, the information which describes segmented areas of original image have been created by proposed labeling method for segmented areas. And then, we have created four subbands which contain the original image's frequency information. Finally, the depth map have been created by frequency map which made with HH, HL subbands and depth information calculation along the each segmented areas. The proposed method can perform efficient depth map creation process because of dynamic allocation using depth information. We also have tested the proposed method using PSNR(Peak Signal to Noise Ratio) method to evaluate ours.

• Journal of the Korean Society of Floral Art and Design
• /
• no.42
• /
• pp.145-156
• /
• 2020

The purpose of this study was to investigate status survey on flower products with high sales by item and peak season. The survey was implemented for 103 people who are running flower shop and are members of association for Engineer Floral Design who are acquired Craftsman Floral Design and Engineer Floral Design. The result of this study, the peak season for the sale of flower product is showed May (52.0%) and February (24.3%). The reason for the selection was in May, month of family, teacher's day, etc. in February, personnel transfer and graduation ceremony. As a result of researching flower products with high sales volume by category, Cut flowers were ranked the first place of bouquet (51.5%%, 40.3%) and the second place of basket (28.8%, 37.5%) on annual and peak season. And also, Corsage, which was 6^th (1.8%) in the annual sales volume survey, increased to 3^rd (8.0%) during peak season. Pot plants were ranked 1st of foliage plant (50.6%, 51.3%) and 2nd tropical orchid·oriental orchids (27.4%, 28.3%) on annual and peak season. And also, Charcoal and bonsai, which were unresponsive in the annual sales survey, increased sales volume to 0.7% and 2.6%, respectively, during peak season. Processed flowers were highest ranked dry flower (45.3%, 39.5%), preserved flower (27.7%, 37.2%) on both non peak season and peak season. And then followed by artificial flower, pressed flower and collage.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.2
• /
• pp.59-66
• /
• 2015

The production of high value-added products requires efficient processing and this constant demand for complex shape processing has led to the need for hybrid processing. In this study, the surface characteristics of hybrid machining, which combines wire-cut E.D.M and vibration, are examined. The selected experimental parameters are verticality, waveform, amplitude, peak current and frequency. The experimental results provide a guideline for selecting reasonable machining parameters. Surface roughness was improved by increasing the amplitude of the vibration.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.1
• /
• pp.81-88
• /
• 2016

Recently, high-efficiency machining in the production of high-value products with complex shapes has constantly been required along with the need for hybrid machining. In this study, in addition to wire-cut Electric Discharge Machining (EDM) and vibration, we present the possibility of a hybrid process by carrying out an experiment with aluminum alloy, and the hybrid process determines the nature of the surface. The selected experimental parameters are waveform, amplitude, peak current, and two-dimensional (2D) vibration. The experimental results give the guideline for selecting reasonable machining parameters. The surface roughness was improved about 20% with increases in the amplitude of the vibration.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.4
• /
• pp.100-107
• /
• 2015

Recently, high-efficiency machining in the production of high-value products with a complex shape has constantly been required with the need for hybrid machining. In this study, in addition to the wire-cut E.D.M. and vibration used to present the possibility of a hybrid process by carrying out the aluminum alloy experiment, the hybrid process determines the nature of the surface. The selected experimental parameters are horizontality, waveform, amplitude, peak current, and frequency. The experimental results give guidelines for selecting reasonable machining parameters. The surface roughness was improved by about 20% with increases in the amplitude of the vibration.