• Nuclear Engineering and Technology
• /
• v.48 no.1
• /
• pp.55-63
• /
• 2016

Calculation of the core neutronic parameters is one of the key components in all nuclear reactors. In this research, the energy spectrum and spatial distribution of the neutron flux in a uranium target have been calculated. In addition, sensitivity of the core neutronic parameters in accelerator-driven subcritical advanced liquid metal reactors, such as electron beam energy ($E_e$) and source multiplication coefficient ($k_s$), has been investigated. A Monte Carlo code (MCNPX_2.6) has been used to calculate neutronic parameters such as effective multiplication coefficient ($k_{eff}$), net neutron multiplication (M), neutron yield ($Y_{n/e}$), energy constant gain ($G_0$), energy gain (G), importance of neutron source (${\varphi}^*$), axial and radial distributions of neutron flux, and power peaking factor ($P_{max}/P_{ave}$) in two axial and radial directions of the reactor core for four fuel loading patterns. According to the results, safety margin and accelerator current ($I_e$) have been decreased in the highest case of $k_s$, but G and ${\varphi}^*$ have increased by 88.9% and 21.6%, respectively. In addition, for LP1 loading pattern, with increasing $E_e$ from 100 MeV up to 1 GeV, $Y_{n/e}$ and G improved by 91.09% and 10.21%, and $I_e$ and $P_{acc}$ decreased by 91.05% and 10.57%, respectively. The results indicate that placement of the Np-Pu assemblies on the periphery allows for a consistent $k_{eff}$ because the Np-Pu assemblies experience less burn-up.

• Journal of Advanced Navigation Technology
• /
• v.21 no.6
• /
• pp.593-600
• /
• 2017

This paper analyzes the performances of direction finding, interference cancellation, and beamforming performance by array antenna pattern measurement distance between the center of array antenna and reference emitter. Array antenna is widely adopted for example as wireless communications, radar, and sonar. In order to use array antenna, array antenna pattern must be known and it can be measured in anechoic chamber. However, the size of anechoic chamber is generally limited. So measurement error of array antenna can be occurred and this could effect performance decrease of direction finding, interference cancellation, and beamforming. It is verified by computer simulation that the performances of direction finding, interference cancellation, and beamforming by array antenna pattern measurement distance.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.35 no.8
• /
• pp.959-967
• /
• 2011

An importance of design that considers the characteristics of fashion that plays a role of a medium that communicates with customers (and is not simply clothes or products by adding the particular culture factors of a local country to the development of glocalism) is discussed. While the cultural consumption becomes a core key word, the survey of customers is conducted to develop a party-wear design that applies a Korean image suitable for the party culture industry magnified by the young generation's cultural trends. Based on it, we suggest a party-wear design that applies Dancheong's lotus and derive the followed results. The first, one-piece and accessory coordination was the highest by 49.3% for the party-wear coordination and design. In addition, Dancheong was the highest by 16.5% for the traditional pattern (thought to be representative for Korean image). Among the traditional patterns, for a pattern suitable for party-wear, the case applying flowers such as the Japanese apricot flower, lotus flower, and peony was the highest. The second, among the several patterns used Dancheong that was represented by a Korean image of a lotus flower pattern because of the characteristics of strong vitality and blooming in dirty mud was often used for the pattern of clothes. The third, under the motive of the results of the survey and Dancheong's lotus flower pattern, we developed 2 methods of one piece and accessory coordination, 2 methods of top and skirt coordination, and 1 method of jacket and one piece coordination as the party-wear.

• Journal of the Korean Regional Science Association
• /
• v.6 no.2
• /
• pp.123-147
• /
• 1990

This paper examines the changing geography of producer service industries in the 1980s. The foci of this study are to analyze the regional distribution of each producer services, and to reveal the spatial linkage of producer services. Further this paper asserts the potential role of producer services for reducing the potential endogenous development in the periphery. During the 1981-86 period, producer service industries grew more rapidly than other service sectors and manufacturing sector. The main reason of the raid growth of producer services is attributable to an increase in demand for intermediate services from manufacturing firms. In order to compete an increasingly complex business environment, firms have expanded the amount of effort devoted to activities such as planning, coordination and control, and consequently have increased their use of producer services. The most distinctive feature of the location of producer services is spatial concentration into Seoul and surrounding region. Especially the degree of the concentration o business services into the Capital Region has been accelerating during the 1990s. The pattern of employment growth and regional distribution of producer services show a clear core / periphery disparity. Much of the regional inequality in producer services is largely due to variation in demand associated with the pattern of corporation headquarters with the pattern of corporation headquarters and branch plants location with large manufacturing firms. The analysis of spatial division of labor reflects that producer services are related to the location of headquarters in manufacturing industry. Headquarters in manufacturing firms and business service firms tend to cluster each other. Most of the headquarters spatially separated from branch offices are clustered heavily in Seoul. Especially headquarters of business services and insurance services are overwhelmingly concentrated into Seoul. The firms whose headquarters are located in Seoul have a linkage pattern on a nationwide scale. It is viewed have little potential for generating local multiplier effects and regional development. In the light of the result of this study, producer services are not likely to disperse soon to peripheral regions. Consequently the absence of policies directed at enhancing producer sevice in the periphery, concentration tendency would continue to reinforce the core's dominance at the expense of peripheral regions. From a regional perspective, the quality of a region's producer service sector is a key determinant of economic growth, since manu industrial location decisions are influenced by the differential availability of producer services among regions. Poor performance of producer services in peripheral regions seemed to be linked to the region's manufacturing base. Low-wage, standardized branch plants are not likely to induce the growth in knowledge intensive services associated with high-technology corporate headquarters. Producer services may help to create and attract new business including manufacturing firms, and also to enhance the productivity and competitiveness of local firms. Therefore the provision of service producing activities would be lead not only to generate and retain endogenous development but also to attract external firms, especially small and medium sized firms which have a lower propensity of internalized services. Hence, it may be more efficient to create and expanse new locally owned producer services rather than to attract branch plants of mult-locational firms in order to make indigenous economic development.

• The Journal of Korean Academy of Prosthodontics
• /
• v.42 no.5
• /
• pp.535-543
• /
• 2004

Purpose: The purpose of this study is to compare the effect of two fiber post systems and one metal cast post system on the fracture strength and fracture pattern of crowned, endodontically treated teeth with 2 mm-height of the reamining tooth structure. Materials and methods: A total of 36 recently extracted sound human mandibular premolars were selected Each tooth structure of the crown portion except 2mm-height of the one above the cementoenamel junction was removed. After being endodontically treated, they were randomly distributed into 3 groups: group 1, restored with quarts fiber post(D.T. Light-Post), group 2, with glass fiber post(FRC Postec), and group 3, metal cast post and core. All teeth were fully covered with nonprecious metal crowns. Each specimen was embedded in an acrylic resin block and then secured in a universal load-testing machine. A compressive load was applied at a 130 degree angle to the long axis of the tooth until fractured, at a crosshead speed 20mm/min. The highest fracture loads were measured and recorded as the fracture strength of each specimen. Fracture areas were measured on the mid-buccal and mid-lingual point from the crown margins. One-way analysis of variance and Turkey test were used to determine the statistic significance of the different fracture loads and areas among the groups (p<0.05). Results: The mean fracture loads were $1391{\pm}$425N(group 1), $1458{\pm}476N$(group 2) and $1301{\pm}319N$(group 3). The fracture loads among the three groups had no statistically signifiant difference (p>.05). The mean fracture area of the fiber post was closer to the crown margin than that of the metal cast post and core(p<.05). The metal cast post showed unrestorable and catastrophic fracture patterns. Conclusion: Within the limitations of this study, fracture loads with any statistically significant difference were not recorded for endodontically treated teeth restored with two fiber posts and the metal cast post. But teeth restored with the fiber posts typically showed the fracture pattern close to the crown margin, which was almost restorable.

• Journal of the Korean Magnetics Society
• /
• v.11 no.6
• /
• pp.239-244
• /
• 2001

Recently, RF inductor having researched by many workers, we fabricated and investigated properties of RF inductors. In order to improve the Q-factor (Quality), we try to apply the patterned Fe$_{78.81}$Ta$_{8.47}$N$_{12.71}$ soft magnetic thin film of 5000 which shows magnetic anisotropy of 30 Oe. Thus, patterned magnetic film was artificially increased magnetic anisotropy lead to increasing of ferro-magnetic resonance frequency up to GHz band. Coil as part of inductor was fabricated by lift off process. The dimension of RF inductor was designed 47un, rectangular shape, and measured properties. In the case of Ti/Ag air core type inductor shows Q of 9, inductance of 8.4 nH at 2 GHz. Magnetic film employed inductor shows inductance of 9 nH and FMR resonance frequency was 700 MHz.

• Ocean and Polar Research
• /
• v.32 no.1
• /
• pp.15-22
• /
• 2010

Calcium carbonate ($CaCO_3$) content was measured from 3 box core (BC060301, BC060303, BC070301) sediments, in addition to pilot core (PC313) sediments, from deep waters within the Western Pacific Ocean. At the two collection sites (BC060301, PC313) located close to the equator, downcore variation exhibited low $CaCO_3$ content during the interglacial period and high $CaCO_3$ content during the glacial period. Variation of coarse fraction (>$63\;{\mu}m$) content also followed changes in $CaCO_3$ content, indicating that dissolution effect of bottom water decreased during the glacial period. Such variation pattern is typical of the Pacific Ocean. However, downcore variation at the two collection sites (BC060303, BC070301) in the Philippine Sea contrasted the trend of the previous two cores (i.e., high $CaCO_3$ content during the interglacial period and low during the glacial period). This pattern is typical of the Atlantic Ocean. Such results may be attributed to the increasing dilution effect, initiated possibly by the increased transportation of terrigenous materials from nearby continent and archipelago during the glacial period when sea level was low. Alternatively, it is possible that the non-carbonate biogenic particles may have been responsible for dilution. Because of these uncertainties, the record of $CaCO_3$ variation in the deep Western Pacific Ocean is not regionally consistent.

• Journal of the Korea Society of Computer and Information
• /
• v.14 no.4
• /
• pp.87-99
• /
• 2009

The top-down method for SOA delivery is recommended as a best way to take advantage of SOA. The core step of SOA delivery is the step of service modeling including service analysis and design based on ontology. Most enterprises know that the top-down approach is the best but they are hesitant to employ it because it requires them to invest a great deal of time and money without it showing any immediate results, particularly because they use well-defined component based systems. In this paper, we propose a service identification method to use a well-defined components maximally as a bottom-up approach. We assume that user's inputs generates events on a GUI and the approximate business process can be obtained from concatenating the event paths. We first find the core GUIs which have many outgoing event calls and form event paths by concatenating the event calls between the GUIs. Next, we adapt sequential pattern mining algorithms to find the maximal frequent event paths. As an experiment, we obtained business services with various granularity by applying a cohesion metric to extracted frequent event paths.

• Journal of KIISE:Software and Applications
• /
• v.35 no.9
• /
• pp.562-571
• /
• 2008

For the purpose of building domain ontology, this paper proposes a methodology for building core ontology first, and then enriching the core ontology with the concepts and relations in the domain thesaurus. First, the top-level concept taxonomy of the core ontology is built using domain dictionary and general domain thesaurus. Then, the concepts of the domain thesaurus are classified into top-level concepts in the core ontology, and relations between broader terms (BT) - narrower terms (NT) and related terms (RT) are classified into semantic relations defined for the core ontology. To classify concepts, a two-step approach is adopted, in which a frequency-based approach is complemented with a similarity-based approach. To classify relations, two techniques are applied: (i) for the case of insufficient training data, a rule-based module is for identifying isa relation out of non-isa ones; a pattern-based approach is for classifying non-taxonomic semantic relations from non-isa. (ii) For the case of sufficient training data, a maximum-entropy model is adopted in the feature-based classification, where k-NN approach is for noisy filtering of training data. A series of experiments show that performances of the proposed systems are quite promising and comparable to judgments by human experts.

• The Journal of Advanced Prosthodontics
• /
• v.1 no.3
• /
• pp.129-135
• /
• 2009

STATEMENT OF PROBLEM. Zirconia-based restorations have the common technical complication of delamination, or porcelain chipping, from the zirconia core. Thus the shear bond strength between the zirconia core and the veneering porcelain requires investigation in order to facilitate the material's clinical use. PURPOSE. The purpose of this study was to evaluate the bonding strength of the porcelain veneer to the zirconia core and to other various metal alloys (high noble metal alloy and base metal alloy). MATERIAL AND METHODS. 15 rectangular ($4\times4\times9mm$) specimens each of zirconia (Cercon), base metal alloy (Tillite), high noble metal alloy (Degudent H) were fabricated for the shear bond strength test. The veneering porcelain recommended by the manufacturer for each type of material was fired to the core in thickness of 3mm. After firing, the specimens were embedded in the PTFE mold, placed on a mounting jig, and subjected to shear force in a universal testing machine. Load was applied at a crosshead speed of 0.5mm/min until fracture. The average shear strength (MPa) was analyzed with the oneway ANOVA and the Tukey's test ($\alpha$= .05). The fractured specimens were examined using SEM and EDX to determine the failure pattern. RESULTS. The mean shear strength ($\pm\;SD$) in MPa was 25.43 ($\pm\;3.12$) in the zirconia group, 35.87 ($\pm\;4.23$) in the base metal group, 38.00 ($\pm\;5.23$) in the high noble metal group. The ANOVA showed a significant difference among groups, and the Tukey' s test presented a significant difference between the zirconia group and the metal group. Microscopic examination showed that the failure primarily occurred near the interface with the residual veneering porcelain remaining on the core. CONCLUSION. There was a significant difference between the metal ceramic and zirconia ceramic group in shear bond strength. There was no significant difference between the base metal alloy and the high noble metal alloy.