• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.5
• /
• pp.1200-1207
• /
• 1996

The paper presents and analyzes two efficient burst-level bandwidth reservation protocols for multi-hop ATM Local Area Networks. With the tell-and-wait (TNW) protocol and the tell-and-go (TNG) protocol[6], a negative acknowledgmen(NACK) message representing the bandwidth starvation on a switch on the source-destnation path can be always sent by a destination. We note that the protocols waste more bandwidth as the round-trip delay increases, since the switches on the path must reserve the bandwidth until the NACK will arrive. Based on this pitfall, the proposed protocols allow and ATM node, rather than a destination node to send a NACK. This allowance can save the needless bandwidth wastage. Using the thinned load approximation method, we show the proposed protocols have good performance and practical simplicity. Thus, the proposed protocols may be candidates for the ABR service in multi-hop ATM LANs and ATM WANs.

• Journal of Power Electronics
• /
• v.15 no.4
• /
• pp.920-928
• /
• 2015

Transformerless solar inverters have a higher efficiency than those with an isolation link. However, they suffer from a leakage current issue. This paper proposes a family of single phase six-switch transformerless inverter topologies with an ac bypass circuit to solve the leakage current problem. These circuits embed two unidirectional freewheeling current units into the midpoint of a full bridge inverter, to obtain a freewheeling current path, which separates the solar panel from the grid in the freewheeling state. The freewheeling current path contains significantly fewer devices and poor performance body diodes are not involved, leading to a higher efficiency. Meanwhile, it is not necessary to add a voltage balancing control method when compared with the half bridge inverter. Simulation and experiments are provided to validate the proposed topologies.

• Journal of Power Electronics
• /
• v.19 no.4
• /
• pp.1011-1019
• /
• 2019

In this paper, a buck-flyback (fly-buck) stand-alone photovoltaic (PV) system for charge balancing with a differential power processor (DPP) circuit is proposed. Conventional feed-back DPP converters draw differential feed-back power from the output of a string converter. Therefore, the power is always through the switches and diodes of the string converter. Because of the returning conduction path, there are always power losses due to the resistance of the switch and the forward voltage of the diode. Meanwhile, the proposed feed-back DPP converter draws power from the magnetically-coupled inductor in a string converter. This shortens the power path of the DPP converter, which reduces the power losses. In addition, the extra winding in the magnetically-coupled inductor works as a charge balancer for battery-stacked stand-alone PV systems. The proposed system, which uses a single magnetically-coupled inductor, can control each of the PV modules independently to track the maximum power point. Thus, it can overcome the power loss due to the power path. It can also achieve charge balancing for each of the battery modules. The proposed topology is analyzed and verified using 120W hardware experiments.

• Journal of Power Electronics
• /
• v.19 no.2
• /
• pp.403-412
• /
• 2019

Aiming at the problems of large dv/dt and di/dt in traditional single-ended converters and high electromagnetic interference (EMI) noise levels, a single-ended isolated converter using the secondary resonance technique is proposed in this paper. In the proposed converter, the voltage stress of the main power switch can be reduced and the voltage across the output diode is clamped to the output voltage when compared to the conventional flyback converter. In addition, the peak current stress through the main power switch can be decreased and zero current switching (ZCS) of the output diode can be achieved through the resonance technique. Moreover, the EMI noise coupling path and an equivalent model of the proposed converter topology are presented through the operational principle of the proposed converter. Analysis results indicate that the common mode (CM) EMI noise and the differential mode (DM) EMI noise of such a converter are deduced since the frequency spectra of the equivalent controlled voltage sources and controlled current source are decreased when compared with the traditional flyback converter. Furthermore, appropriate parameter selection of the resonant circuit network can increase the equivalent impedance in the EMI coupling path in the low frequency range, which further reduces the common mode interference. Finally, a simulation model and a 60W experimental prototype of the proposed converter are built and tested. Experimental results verify the theoretical analysis.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.6
• /
• pp.584-597
• /
• 2011

In this paper, low-loss and high-power RF SP6T switch chips are designed, fabricated and measured for GSM/EGSM/DCS/PCS applications using WIN Semiconductors 0.5 ${\mu}m$ pHEMT process. We utilized a combined configuration of series and series-shunt structures for optimized switch performance, and a common transistor structure on a receiver path for reducing chip area. The gate width and the number of stacked transistors are determined using ON/OFF input power level of the transceiver system. To improve the switch performance, feed-forward capacitors, shunt capacitors and parasitic FET inductance elimination due to resonance are actively used. The fabricated chip size is $1.2{\times}1.5\;mm^2$. S-parameter measurement shows an insertion loss of 0.5~1.2 dB and isolation of 28~36 dB. The fabricated SP6T switch chips can handle 4 W input power and suppress second and third harmonics by more than 75 dBc.

• International Journal of Highway Engineering
• /
• v.10 no.3
• /
• pp.79-86
• /
• 2008

This paper proposed the appropriate installation angle of skewed sensors for measuring vehicle wandering data, which are collected to figure out the location of dynamic weight of a moving vehicle on roadways. We developed a device using tape-switch sensors and a computer program and collected vehicle wandering data with the device and probe vehicles. As a result, the steeper the skewed sensor was installed, the lower the error was shown. However, we could not collect proper data when a skewed sensor was set up higher than $30^{\circ}$ due to tandem axle. Therefore, this study suggested the appropriate angle of skewed sensors as a degree of $20^{\circ}$ to $25^{\circ}$ for gathering wandering data.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.2
• /
• pp.6-12
• /
• 2001

When CBR source traffics are loaded to ATM switch and broadband network termination, CTD values of ATM switch and broadband network termination are measured and then the values of CTD in the domestic region arc estimated. The estimation values of CTD satisfy the objective of CTD in the domestic region allocated by allocation rules of 1.356. The peak-to-peak CDV allocation method based On Chernoff accumulation method is proposed and applied to the nodes of national portion. From the result of numerical analysis, the proposed method is more accurate than the equal allocation method for peak -to-peak CDV in case that the CDVs at each node and the number of ATM nodes on the path increase.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.511-519
• /
• 2016

This paper proposes a CMOS 6-bit phase shifter with low RMS phase and amplitude errors for an X-band phased array antenna. The phase shifter combines a switched-path topology for coarse phase states and a switch-filter topology for fine phase states. The coarse phase shifter is composed of phase shifting elements, single-pole double-throw (SPDT), and double-pole double-throw (DPDT) switches. The fine phase shifter uses a switched LC filter. The phase coverage is $354.35^{\circ}$ with an LSB of $5.625^{\circ}$. The RMS phase error is < $6^{\circ}$ and the RMS amplitude error is < 0.45 dB at 8-12 GHz. The measured insertion loss is < 15 dB, and the return losses for input and output are > 13 dB at 8-12 GHz. The input P1dB of the phase shifter achieves > 11 dBm at 8-12 GHz. The current consumption is zero with a 1.2-V supply voltage. The chip size is $1.46{\times}0.83mm^2$, including pads.

• The Transactions of the Korea Information Processing Society
• /
• v.6 no.3
• /
• pp.722-728
• /
• 1999

When one link failure happens in BSHR/2 networks, it is possible to restore all traffics by following the ITU-T G.841 rules. However, when a node that is currently executing a ring switch receives a long-path ring bridge request for an higher priority, it shall drop its bridge and switch immediately, then enter full pass-through. Even through link connection between two nodes exists, it is impossible to restore the service. In this paper, when multi-link failures happen, the services through connected link can be restored by exchanging messages through DCC(Data Communication Channel). Partially reconstructing the ring map that is unable to restore services because of multi-link failures made it possible to restore these kinds of traffic pattenrs. This paper shows that the services through connected link can be restored by using proposed method.

• Smart Media Journal
• /
• v.13 no.1
• /
• pp.52-59
• /
• 2024

This paper proposes a plan to improve the reception radio environment of the mobile terminal and maintain a constant reception electric field by using small cells in a small closed environment. In order to configure an efficient communication infrastructure for small cells, both ends of wireless transmission and reception of an Ethernet-based wireless video recording system are connected using an L2 switch. The small cell connected to the receiving side L2 switch shares the wireless network section of the wireless video recording system and connects to the transmitting side L2 switch. After that, when it is normally linked to FMS, a management system for small cells, through the Internet network, the output of small cells is checked. In order to verify the results, a proposed network is formed on the elevator inside the building with a poor radio wave environment, and the radio wave environment is measured before and after the small cell application in the section where the elevator operates. As a result, the main parameters of the radio wave environment in all sections of the elevator are improved, as well as a constant receiving electric field strength within the moving elevator.