• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.4
• /
• pp.181-186
• /
• 2011

Thermal stability of the $TiO_2$ SCR catalyst with W03 loading was investigated in terms of structural and morphological analyses. The $TiO_2$ catalysts with 10 w% $WO_3$ content and without $WO_3$ were prepared. which were heat-treated at $800^{\circ}C$ for 5 h. It was found that the catalytic acidity was decreased by thermal degradation in the $WO_3-TiO_2$ specimen that relatively less than the $TiO_2$ specimen from FT-IR analysis. The phase transition of the $TiO_2$ catalyst from anatase to rutile was increased by heal-treatment, and the percentage of the rutile phase was 28.4 % in the $WO_3-TiO_2$ and 22.9 % in the $TiO_2$. A shell region of $WO_3$ distinguished from a $TiO_2$ particle was also observed in the grain boundary region, and the $WO_3$ led to the suppression of grain growth. It could be confirmed that the suppression of grain growth can contribute to the improvement of catalytic properties for thermal stability more than the increase of anatase-rutile phase transformation which cause the reduction of the catalytic activity in the $TiO_2$ SCR catalyst by the presence of $WO_3$.

• Journal of the Korea Concrete Institute
• /
• v.18 no.5 s.95
• /
• pp.687-693
• /
• 2006

The Stone Powder Sludge(below SPS) is the by-product from the process that translates stone power of 8mm under as crushed fine aggregate. It is the sludge as like cake that has average particle size of $7{\mu}m$, absorbing water content of 20 to 60%, and $SiO_2$ content of 60% over. Because of high water content of SPS, it is not only difficult to handle, transport, and recycle, but also makes worse the economical efficiency due to high energy consuming to drying. This study is aim to recycle SPS as it is without drying. Target product is the lightweight foamed concrete that is made from the slurry mixed with pulverized mineral compounds and foams through hydro-thermal reaction of CaO and $SiO_2$. Although in the commercial lightweight foamed concrete CaO source is the cement and $SiO_2$ source is high purity silica powder with $SiO_2$ of 90%, we tried to use the SPS as $SiO_2$ source. From the experiments with factors such as foam addition rate and replacement proportion of SPS, we find that the lightweight foamed concrete with SPS shows the same trends as the density and strength of lightweight foamed concrete increases according to decrease of foam addition rate. But in the same condition, the lightweight foamed concrete with SPS is superior strength and density to that with high purity silica. This trends is distinguished according to increase of replacement proportion of SPS, also the analysis of XRF shows that the hydro thermal reaction translates SPS to tobermorite. Although SPS has low $SiO_2$ contents, the lightweight foamed concrete with SPS has superior strength and density, because it reacts well with CaO due to extremely fine particles. We conclude that it is possible to replace the high purity silica as SPS in the lightweight foamed concrete experimentally.

• Korean Chemical Engineering Research
• /
• v.43 no.4
• /
• pp.503-510
• /
• 2005

In this research, composite alumina was prepared to add the various promoters by sol-gel method and examined its thermal stability. After sintering at $1,200^{\circ}C$, the thermal stability resulted in following order, $Si{\fallingdotseq}La$ > Ti > $Ba{\fallingdotseq}Ce$ > Y > $Zr{\fallingdotseq}Mg$, in accordance with adding the promoters. Especially in case of silica-added alumina, a phase transformation temperature to ${\alpha}$-alumina increased about $150^{\circ}C$ and after sintering at $1,200^{\circ}C$, it showed to maintain in ${\gamma}$-form and ${\delta}$-form alumina phase. Also it showed an increase of surface area from $3m^2/g$ to $71m^2/g$ compared with pure ${\alpha}$-alumina. In the case of silicaadded alumina, the characterization change of this alumina particle resulted in a delay of phase transformation because Si-O-Al bond was increased when sintered at high temperature. In case of lanthanum-added alumina, there was a sintering delay phenomenon in inter-particles as $LaAlO_3$ structure existed. The existence of lanthanum structure was confirmed by XRD and XPS analysis. It appeared on the alumina surface as $La_2O_3$ structure when it was sintered under $1,000^{\circ}C$, as the perovskite structure of $LaAlO_3$ at above $1,000^{\circ}C$ and as the magneto-plumbite structure of $LaAl_{11}O_{18}$ at above $1,300^{\circ}C$.

• Research in Plant Disease
• /
• v.17 no.2
• /
• pp.191-195
• /
• 2011

This experiment was attempted to investigate a cause of the scion death in green pepper grafting system. A tobamovirus particle examined in the rootstock of the sample but not in the scion showing necrosis. The virus isolated from the rootstock was identified as Pepper mild mottle virus (PMMoV), pepper tobamovirus pathotype P1.2. (PMMoV-2), by nucleotide sequence analysis and host plant reaction. The virus isolate infected systematically in 6 commercial rootstock varieties using for green pepper grafting seedling production. Green pepper varieties 'Long green mart' and 'Daechan' represented resistance to the virus showing local lesions only on the inoculated leaves and 'Manitda' was systematically infected. In the experiment with grafting 'Long green mart' or 'Daechan' onto the those rootstocks, the upper leaves of the scions first showed vein necrosis and wilt symptoms 7 days after inoculation with PMMoV-2 on the cotyledon of the rootstock, following to the scion stem necrosis and then only the scion death. The virus was detected in the rootstock but not in the scion. However, 'Manitda' of susceptible variety in the grafting system showed mottle symptom on the leaves of the scion but not necrosis on the plant. PMMoV-3 isolate, pepper tobamovirus pathotype P1.2.3, did not cause the scion death in the grafting system. All of the varieties were susceptible to PMMoV-3. These results suggest that the scion death is caused by infecting with pepper tobamovirus pathotype P1.2. in the green pepper grafting system combined with the susceptible rootstock and the resistance scion to the virus pathotype.

• Journal of Environmental Impact Assessment
• /
• v.24 no.6
• /
• pp.578-592
• /
• 2015

To investigate characteristics and seasonal variations of carbonaceous species for $PM_{2.5}$ in Seoul metropolitan area, Korea, we measured organic carbon (OC) and elemental carbon (EC) from January 2014 to December 2014 using a semi-continuous OC/EC Analyzer (Model-4, Sunset Lab.). Mean concentrations of OC and EC were estimated $4.1{\pm}2.7{\mu}g/m^3$ and $1.6{\pm}1.0{\mu}g/m^3$, respectively. The annual averaged OC/EC ratio was $2.9{\pm}2.7$. Concentrations of OC and EC comprised 13% and 5% of $PM_{2.5}$ and the mass fraction of both was the highest in fall. OC and EC showed similar trend in seasonal variations. Concentrations of those showed a clear seasonal variation with the highest in winter and the lowest in summer. The correlations between the two were the best during the winter ($r^2=0.88$). As results of carbonaceous species analysis, the dominant factor in view of fine particle ($PM_{2.5}$) is primary emission source such as mobile, fossil fuel combustion during commute time(08:00~10:00 or 17:00~21:00) and winter season. Continuous monitoring of atmospheric carbonaceous species is essential to provide the science-based data to policy-maker establishing the air quality improvement policy.

• Journal of Wetlands Research
• /
• v.19 no.1
• /
• pp.30-36
• /
• 2017

SS(Suspended Solid) concentration by soil erosion into river at normal and flood season should be measured. However, to present the variation of SS due to various development project such as EIA(Environmental Impact Assessment), River Master Plan, and so on, it is necessary to estimate not measure SS, but there are not exist how to estimate SS. In the present study, therefore, we propose the hydrologic method of estimating SS concentration using the results of particular frequency flood discharge and sediment discharge by RUSLE method. SS consists of silty and clay soil and colloid particle etc. However, in the present study, silty and clay soils of sediment discharge except send set up SS standards. The flow discharge to estimate SS concentration are 1~2 years for normal season, 30~100 years for flood season. Meanwhile, analysis software for probable rainfall uses Fard2006, probable rainfalls under 2-year frequency are estimated using rainfall data and frequency factor of Gumbel distribution. The results of estimating SS concentration using runoff volume by sediment and flow discharges of silty and cray soils as above method show that reliable level of SS concentration is considered in predevelopment of natural condition and under development of barren condition. Especially, SS concentration takes notice that the value of sediment discharge makes a huge difference according to channel slope, it was confirmed that the value obtained by dividing the SS concentration by the channel slope is relatively constant even though the topographical factors are different. Therefore, if the present study will be proceeded for various watersheds, it will be developed as estimation method of SS concentration.

• Korean Journal of Ecology and Environment
• /
• v.33 no.3 s.91
• /
• pp.187-196
• /
• 2000

This paper describes a simple method that uses differences among Carlson's (1977) trophic state index (TSI) values based on total phosphorus (TP), chlorophyll a (CHL) and Secchi depth (SD) to draw inferences regarding the factors that are limiting to phytoplankton growth and the composition of lake seston. Examples are provided regarding seasonal and spatial patterns in a large subtropical lake (Lake Okeechobee, Florida, USA) and inter- and intra-lake variations from a multilake data set developed from published studies. Once an investigator has collected routine water quality data and established TSI values based on TP, CHL, and SD, a number of inferences can be made. Additional information can be provided where it also is possible to calculate a TSI based on total nitrogen (TN). Where TSI (CHL)<>TSI (SD), light attenuating particles are large (large filaments or colonies of algae), and the phytoplankton may be limited by zooplankton grazing. Other limiting conditions are inferred by different relationships between the TSI values. Results of this study indicate that the analysis is quite robust, and that it generally gives good agreement with conclusions based on more direct methods (e.g., nutrientaddition bioassays, zooplankton size data, zooplankton removal experiments). The TSI approach, when validated periodically with these more costly and time-intensive methods, provides an effective, low cost method for tracking long-term changes in pelagic structure and function with potential value in monitoring lake ecology and responses to management.

• Korean Journal of Soil Science and Fertilizer
• /
• v.38 no.6
• /
• pp.301-306
• /
• 2005

Asian dust was collected in Korea and soils in the arid area of northern China were analysed for its physical and chemical properties, and mineral compositions for in order to interpret the origin of Aeolian soils and estimate the effect of dust wind on the soil environment in Korea. Asian dust was collected at Suwon in Korea from 2002 to 2004. Soil samples were collected from the desert and Loess plateaus around Gobi desert in China. As a result of analysis of desert soil distributed on northern region and Loess soils in China, it was observed that soil pH was about 9, organic matter 11 to $23g\;kg^{-1}$, and CEC 7.1 to $18.4cmolc\;kg^{-1}$, showing a high spatial variation among different sampling locations. About 62 to 80% of particles were composed of quartz and feldspars, 2 to 14% calcite ($CaCO_3$) and dolomite [$Ca{\cdot}Mg(CO_3)_2$], and trace other clay minerals. All the dust particles in Korea were below 50 m in diameter, and the mineral compositions were quartz, mica, feldspar and some clay minerals. Major components of clay mineral of Asian dust was mainly illite as compared to the kaolin of soils in Korea. The base saturation of exchangeable Ca, Mg, K and Na in the Asian dust was above 250% due to the high content calcite. Most of upland soil in Suwon was thin and sharp type, but Asian dust in Korea was the spherical shape. Asian dusts in Suwon, Korea, did not show a definite mineralogical variation of the dust during the collection period. Difference between the Asian dust collected in Korea and the soils in arid area of China was observed in the physical and chemical properties, especially for particle size distribution, cations such as Ca, Mg, K and Na. However, some similarities were found on the mineral compositions and chemical properties between Asian dust collected in Korea and the loess of China.

• Korean Journal of Food Science and Technology
• /
• v.46 no.6
• /
• pp.750-756
• /
• 2014

This study was performed to understand the effect of cultivation periods on the physicochemical characteristics of the starch of five sweetpotato cultivars, cultivated in Muan, Korea. Starch, protein, and ash contents increased with increased cultivation period, whereas amylose content decreased. Rapid viscosity analysis showed that the pasting temperature, peak viscosity, breakdown, setback and final viscosity increased with increased cultivation period. However, trough and final viscosity decreased. Although the onset temperature and peak temperature values increased, the conclusion temperature did not show any consistent patterns by differential scanning calorimetry. X-ray diffraction showed that the starch samples had C-type crystallinity irrespective of the cultivation period and cultivar. The starch granules were dominantly round and oval, or polygonal irrespective the cultivation period. The bigger the particle size was, the longer the cultivation period was.

• Journal of Periodontal and Implant Science
• /
• v.24 no.1
• /
• pp.131-143
• /
• 1994

For maintenance of exposed implant in healthy state, it is necessary to treat the surface of implant fixture and provide the surface adjustable to surrounding tissues. Variable techniques have been introduced such as citric acid and air-abrasive system to treat the failed implant. Although when the rough surface of HA coated implant was exposed to oral environment, the surface treatment method with citric acid or air-abrasive system is effective for removal of bacterial endotoxin, it is unsuccessful to prevent plaque deposition due to difficulty in removal of rough surface of HA coated implant. Thus, in this study the method that removes bacterial endotoxin and makes smooch surface without alteration of surface characteristics was studied. HA coated disc manufactured by IMZ Co. Was treated with high speed diamond bur, low speed diamond bur, stone bur, rubber point, jetpolisher. And then its surface state was examined with profilometer and SEM to evaluate the surface smoothness, and its surface component was analyzed with EDX to evaluate wheter the surface characteristics were altered or not. As a result, following results were obtained. When the surface roughness of each implant disc was measured by profilometer, the group I showed a $R_{max}\;2.11{\mu}m$ and the group II, III, IV, V showed a $R_{max2}\;4.17{\mu}m$, $7.28{\mu}m$, $8.61{\mu}m$ and $39.44{\mu}m$ respectively. That is, surface smoothness was highest in the group I and it has been gradually decreased in the group II, III, IV and V. Under the SEM examination, the group I showed relatively smooth surface and the group II showed slightly rougher surface than the group I due to partially remaining HA particles while most HA particle was removed. The group III and IV showed rough topography due to HA particles that was not grinded, and HA coated surface in group V showed very irregular surface with deep groove and prominence. In cross-sectional view, the group I showed uniform surface, and the group III, IV showed rough surface due to remaining HA particles but the thickness of HA coating was remarkably reduced. The group II has similar pattern in group I, and the group V showed about $40{\mu}m$ thickness although it was not constant. By analysis of surface component with EDX, the group II in which the grinding was effective showed a small quantity of calcium and phosphorous and the group III, IV, in which the grinding was incomplete showed calcium and phosphorus peak. In all experimental group, no other than titanium, aluminum, calcium, phosphorus was observed.