• Journal of Powder Materials
• /
• v.16 no.4
• /
• pp.243-248
• /
• 2009

Carbon-coated Cu nanopowders with core/shell structure have been successfully fabricated by pulsed wire evaporation (PWE) method, in which a mixed gas of Ar/$CH_4$ (10 vol.%) was used as an ambient gas. The characterization of the samples was carried out using x-ray diffraction (XRD), scanning electron microscope (SEM), and high resolution transmission electron microscope (HRTEM). It was found that the nanoparticles show a spherical morphology with the size ranging of 10-40 nm and are covered with graphite layers of 2-4 nm. When oxygen-passivated Cu nanopowders were annealed under flowing argon gas (600 and 800$^{\circ}C$), the crystallinity of $Cu_2O$ phase and the particle size gradually increased. On the other hand, carbon-coated Cu nanopowders remained similar to as-prepared case with no additional oxide or carbide phases even after the annealing, indicating that the metal nanoparticles are well protected by the carbon-coating layers.

• Journal of Pharmaceutical Investigation
• /
• v.34 no.5
• /
• pp.363-368
• /
• 2004

In order to investigate the effect of bovine serum albumin (BSA), as a pore former, on the controlled release of an antibiotic from a biodegradable polymeric device, polycaprolactone (PCL)-cefadroxil matrices were prepared by the solvent casting method. The amount of cefadroxil released from various formulations at $37^{\circ}C$ was measured by HPLC. The duration of antimicrobial activity of matrices against S. aureus was evaluated by measuring the diameters of the inhibition zone. The morphology of the matrices was investigated by scanning electron microscopy (SEM). The release rate and extent of cefadroxil from PCL matrix increased as the loading dose and particle size of BSA/cefadroxil mixture powder increased. Cefadroxil released from the matrix exhibited antibacterial activity for up to 4 days. SEM of the cross-section of matrix showed the typical channel formation after 3 days of release study. Thus, a biodegradable polymeric matrix loaded with antibiotic/BSA mixture can effectively prevent bacterial infection on its surface, thereby bringing about an enhancement of biocompatibility of biomaterials.

• Analytical Science and Technology
• /
• v.13 no.3
• /
• pp.332-337
• /
• 2000

The study on the nitrogen adsorption, surface properties and water adsorption capacity of the carbonaceous desiccants derived from phenolic resin was carried out. In the nitrogen adsorption study on the carbonaceous desiccants, Type II isotherm for each sample was obtained. Furthermore, the adsorbed volume decrease with water washing of the desiccant. The $S_{BET}$ of the carbonaceous desiccants was $648.7m^2/g$ before washing and $189.3m^2/g$ after washing, respectively. The morphology of needlelike formation before washing and spherical particle after washing with water were observed from SEM micrographs. Finally, from the water adsorption effects, the percentage of the water loading capacity was 25-63%, and the capacity was good at relatively low humidity.

• Journal of Korean Society for Atmospheric Environment
• /
• v.29 no.2
• /
• pp.152-162
• /
• 2013

The physico-chemical characteristics and nanostructure of the aerosol samples from a coal-fired power plant, a charcoal kiln and diesel vehicles were investigated with focusing on black carbon (BC). Aerosols from the coal-fired power plant were mostly comprised of mineral ash spheres which are heterogeneously mixed. The main components of the aerosols from coal-fired power plant were calcium compounds, iron oxide, alumino-silicate without BC. The typical combustion-generated BC which shows the shape of bunch of grapes with 20~50 nm particles which were detected in aerosol particles from diesel vehicles. The nanostructure of each BC particle shows the shape of concentric circles which is comprised of closely-packed graphene layers. Aerosols from charcoal kiln were likely condensed organic carbon generated from the low-temperature combustion process.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.1
• /
• pp.50-55
• /
• 1999

To develop a new form of controlled release dosage for administering for indomethacin (IND), two formulations of IND-loaded nanoparticles were designed based on polysaccharide (guar) derivatives. Nanoparticles prepared by the dialysis method were characterized with respect to morphology, size distribution, drug content, and in vitro drug release. Morphological studies by scanning electron microscopy (SEM) indicated that guar acetate (GA) nanoparticles were spherical in shape and had a smooth surface. The particle size distributions of formulation I (40mg of GA) and formulation II (80mg of GA) were shown to be $250.78\pm185.13nm$ and $718\pm145.90nm$ in distilled water ($20$^{\circ}C$), respectively. The drug loading efficiencies of nanoparticles were approximately 26% and 31% for formulations I and II, respectively. The differential scanning calorimetry (DSC) results indicated that the IND was perfectly distributed within GA nanoparticles. We also found, from the X-ray diffractometry analysis, that a decrease in the degree of crystallinity of the drug occurred in the nanoparticles. No changes between the original IND and the released IND from GA nanoparticles were detected by FT-IR. Using guar acetate, it is possible to design nanoparticles which allow the controlled release of IND over an extended period of time.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.18 no.3
• /
• pp.219-225
• /
• 2005

To investigate the effects of slurry temperature on the chemical mechanical polishing(CMP) performance of oxide film with silica and ceria slurries, we have studied slurry properties as a function of different slurry temperature. Also, the effects of each input parameter of slurry on the oxide CMP characteristics were investigated. The pH showed a slight tendency of decrease, the conductivity in slurries showed an increased tendency, the mean particle size in slurry decreased, and the zeta potential of slurry decreased with temperature. The removal rates significantly increased and maintained at the specific levels over 4$0^{\circ}C$. The better surface morphology of oxide films could be obtained at 40 $^{\circ}C$ of silica slurry and at 90 $^{\circ}C$ of ceria slurry. It is found that the CMP performance of oxide film could be significantly improved or controlled by change of slurry temperature.

• Korean Journal of Materials Research
• /
• v.16 no.5
• /
• pp.285-291
• /
• 2006

Copper powders have been widely used in electrically conductive coatings, electrode materials et al. and are very prospective since they are cheaper than noble metal powders such as silver or palladium. In this study, copper powders for metal filler of EMI shielding have been prepared using a solvothermal process from $CuSO_4$, NaOH, Glucose, mixed solvent ($H_2O$: Ethanol) and hydrazine which was used as a reducing agent at various reaction conditions. The prepared copper powders showed finely dispersed spherical shape without agglomerate, uniform morphology, narrow size distribution, high purity and were about 400-700 nm in size. The prepared powders were characterized using XRD, SEM, TGA, XPS, particle size measurement and EMI shielding efficiency.

• Proceedings of the Polymer Society of Korea Conference
• /
• 2006.10a
• /
• pp.262-262
• /
• 2006

Biodegradable and amphiphilic di-block and tri-block copolymers, prepared with monomethoxy poly ethylene glycol (MPEG) and ${\varepsilon}-caprolactone\;({\varepsilon}-CL)$, were used for the application of W1/O/W2 multi- emulsion capsules. The effects of topology and the ratio of hydrophilic moiety of PCL-based polymers on the encapsulation efficiency of the $W_{1}/O/W_{2}$ multi-emulsion capsules containing Ascorbic Acid-2-Glucoside (AA-2-G) were investigated. The ratio of PEG and PCL was 1:0.5, 1:0.75, 1:1, and 1:1.25. PEG-PCL block copolymers were added to the first step of the preparation of $W_{1}/O$ emulsions. The dispersion stability, the particle size, the morphology of the $W_{1}/O/W_{2}$ multi-emulsion capsules were observed using an on-line turbidity meter, dynamic light scattering (DLS), a confocal microscopy (with FITC) and an optical microscopy. Biodegradable behavior of the PEG-PCL block copolymers and release behavior of AA-2-G were also observed by Gel Permeation Chromatography (GPC) and High Performance Liquid Chromatography (HPLC).

• Polymer(Korea)
• /
• v.37 no.3
• /
• pp.356-361
• /
• 2013

Microcapsules of two different self-healing agents, 5-ethylidene-2-norbornene (ENB) and ENB with a crosslinker, surrounded by a melamine-urea-formaldehyde shell were manufactured. In this work, a red dye was incorporated into the self-healing agents as a tracer for better visual observations. It revealed that the incorporation of a red dye into self-healing agents did not disturb the formation of microcapsules from the examination of thermal resistance, particle size/size distribution and morphology of the resulting microcapsules. Releasing of self-healing liquid into the induced crack from ruptured microcapsules and filling between crack planes were observed using an optical microscope. Also observed was the reaction of filled healing agent with embedded Grubbs' catalyst in an epoxy coating layer.

• Tribology and Lubricants
• /
• v.13 no.4
• /
• pp.60-65
• /
• 1997

The tungsten disulfide $(WS_2)$ solid lubricant was synthesized by two different reaction processes, i.e., the reaction between $CS_2$ gas phase and solid $WO_3$powder, and the vapour phase transport method of tungsten and sulfur in a high vacuum. The chemical and physical characteristics of synthesized $WS_2$powder were analyzed in terms of the average particle size, morphology, crystalline phase etc. in comparison with those of commercial $WS_2$powder. The solid $WO_3$ powder with the average size of 0.2 ${\mu}{\textrm}{m}$ was reacted with $CS_2$gas flowed with$N_2$or 96%$N_2{\times}4%H_2$forming gas for 36 h and 24 h at 90$0^{\circ}C$ respectively. $WS_2$ crystalline phase was then formed through the intermediate phase of .$W_{20}O_{58}$ In the case of vapour phase transport method, the 3.5 wt% iodine was added as a vapour transport reagent into the composition of tungsten and sulfur powders maintaining a constant molar ratio of W:S=1:2.2. The mixture was then heat treated at 85$0^{\circ}C$ for 2 weeks in vacuum. The reaction product obtained showed the average size of 12 ${\mu}{\textrm}{m}$ and the hexagonal plate shape of typical solid lubricant with 2H-$WS_2$crystalline phase.