• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1558-1560
• /
• 2001

네트워크 분석기를 이용하여 GIS용 UHF 부분방전 검출장치가 CIGRE 권고안을 만족시킴을 보일 수 있는 방법을 제안하였다. 이 방법은 운전중인 GIS에서도 활용이 가능하며 주파수 영역에서 GIS 내 부분방전신호의 감쇠율을 정확히 측정할 수 있고 측정 시스템의 개별부품에 대한 교정이 필요치 않다. 또한 측정한 GIS의 구간별 감쇠율을 이용해 센서의 종류와 부분방전검출장치 및 GIS의 구성에 따라 센서의 위치를 손쉽게 결정할 수 있다.

• Proceedings of the KIEE Conference
• /
• 2000.07e
• /
• pp.52-55
• /
• 2000

In this paper, the coupled and the non-coupled vibration mode AE sensor for GIS were simulated by finite element analysis and manufactured, and characterized. The maximum sensitivity was 64.3 dB when the resonant frequency of the coupled vibration mode AE sensor was 166 kHz and the maximum sensitivity was 58.9 dB when the resonant frequency of the non-coupled mode AE sensor was 265 kHz. The coupled vibration mode AE sensor responded higher than the non-coupled vibration mode AE sensor at the partial discharge detection in GIS.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1528-1530
• /
• 1998

In this work, a possible new PD detection technique, based on the Michelson Interferometer, has been proposed. Laser beam transmitted by optical fiber is spliced into two-laser beam by 50/50 coupler, one is reflected on diaphragm, which is vibrated by ultrasonic sound, and then modulated. The other one is reference beam. They are collected into 50/50 coupler making interferenced beam which could be detected by photo detector.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1714-1716
• /
• 2002

Optical fiber sensor is a subject which has been attracted considerable attention in recent year. Especially, it is being developed for the detection and location of partial discharge in oil-filled transformers. In this paper, we propose and experimentally demonstrate directivity and sensitivity of a hollow cylindrical mandrel sensor. The sound source is a PZT actuator of hollow cylinder type. Several layers of the fiber laminated around the mandrel surface and experiments were performed on three axis modes. The experimental results can be applied to analyze detected signals optimally.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.1081-1083
• /
• 1999

The capacitive coupling technique has been used as conventional method for PD detection on the power cable line. Recently, however PD measurement using by high frequency is known to have an excellent sensitivity comparison with low frequency on-site. In this paper, the high frequency characteristic of two type of metal foil sensor was studied and the technique was proved to be more effective diagnostic method than conventional method for qualification of EHV cable and accessories.

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.516-518
• /
• 2000

정상 상태의 gas-insulated switchgear (CIS) 내부에서 발생한 부분방전 신호를 검출 할 수 있는 UHF 부분방전 검출 센서를 실험용 362 kV GIS에 적용하였다. GIS 내부에 알루미늄 이물질을 투입한 다음 120 - 180 kVrms 전압을 단계적으로 인가하고 장시간 인가전압 위상에 대한 UHF 부분방전 신호를 측정하였다. 인가전압을 높일수록 검출된 방전신호의 간격이 늘어났으며, 이물질로 사용한 알루미늄선의 길이가 길어질수록 이물질의 상승고도는 증가하였다. GIS 내부에서 이물질의 운동에 대한 간단한 계산에서도 비슷한 경향을 보임을 확인하였다.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2434-2437
• /
• 1999

In order to detect the ultrasonic that is generated by the partial discharge of the heavy electric machinery, a Laser Doppler Vibrometer (LDV) was developed. A Michelson type interferometer which employed heterodyne signal process technique was built to measure the frequency and amplitude of vibration. The output signal of the fast photodetector was a frequency modulated signal centered at 40 MHz. The signal from the detector was amplified and downconverted to intermediate frequency centered at 1 MHz after mixing process. The voltage output that was proportional to the velocity of the moving surface(PZT) was obtained using PLL. The spectrum of the FM signal was analyzed and integration method was introduced to obtain amplitude information. This LDV can be used to measure the vibration of MEMS devices, automobiles, HDD and CDP.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.447-451
• /
• 2009

Metropolitan rapid transit has been used by one of a main transport service for several decades, but there are no monitoring system for electrical equipment condition which can cause enormous economic loss and social problem if fault occurs. Recently, necessity of condition monitoring system for electrical equipment fault came to the fore, we became carrying out a research project for a design of electrical equipment lifetime estimation system for metropolitan rapid transit. In this paper, basic design result of condition monitoring system and specification of transformer partial discharge detection system are presented, which are part of entire lifetime estimation system. Definition of target apparatus and monitoring method determined by analysis of user requirement from each railway company and, each railway company's opinions and requests were collected sufficiently by surveys and discussion.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.8
• /
• pp.343-349
• /
• 2005

The gas in oil analysis of transformer is the most widely used technology for diagnosis of transformer in the world. It has brought excellent results to prevention of transformer failure. The criteria for maintenance and judgement, however, is still required continuous supplement to improve the accuracy of the diagnosis on the basis of accumulated data of gas analysis and investigations in the transformer In this study, the relationship between the detection rate of the defects and the source of troubles are analyzed according to the investigation in the transformer, which was conducted by KEPCO in 2004. As a result, the validity of the criteria being used at present was examined thoroughly.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.285-288
• /
• 1998

Ultrasonic signal characteristics related with the growth of electrical trees in epoxy resin are examined under 67[Hz] ac voltage application along with a CCD camera and PD current method. The ultrasonic sensor with a resonant frequency of 200[Hz] supported by a mechanical spring is attached directly to the lower-side of plane electrode. The magnitude of Partial discharge and count rate of ultrasonic signals have been measured according to the tree growth from a needle tip in an epoxy sample.